When replacing an injector (including interchanging injectors between cylinders) or common rail, replace the corresponding injection pipes with new ones.
When fuel lines are disconnected, air may enter the fuel lines, leading to engine starting trouble. Therefore, perform forced regeneration and bleed the air from the fuel lines.
1.CHECK INJECTOR COMPENSATION CODE
Check that the injector compensation code registered in the injector assembly installed on each cylinder matches the one registered in the engine ECM.
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION
If the code does not match, follow the procedures below to correct the registration details and recheck the symptom.
Correct the registration details by following the procedures in "Register Injector Compensation Code".
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION
After correcting the registration details, check if the symptom that occurred when the vehicle was brought in recurs.
If it does not occur, the symptom may be caused by errors in the injector compensation code registration.
2. PRECAUTION
After turning the ignition switch off, watching time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
4.DRAIN ENGINE COOLANT
17940D 5.REMOVE INTERCOOLER ASSEMBLY
23810A 6.REMOVE COMMON RAIL
23801L 7.REMOVE FUEL FILTER TO INJECTION PUMP FUEL PIPE SUB-ASSEMBLY
8.DISCONNECT NO. 2 ENGINE WIRE
27148B 9.REMOVE CONNECTING WIRE
Detach the 2 clamps and remove the connecting wire.
23763 10.REMOVE NO. 3 NOZZLE LEAKAGE PIPE
| *a | Injector Hollow Screw |
| *b | Bolt |
Remove the 2 injector hollow screws, 3 bolts, No. 3 nozzle leakage pipe and 2 gaskets.
When removing the nozzle leakage pipe, place a cushion under the pipe.
Be careful not to deform or scratch the union seal surface.
After removing the nozzle leakage pipe, put it in a plastic bag to prevent foreign matter from contaminating its injector inlet.
23761A 11.REMOVE NO. 1 NOZZLE LEAKAGE PIPE
| *a | Injector Hollow Screw |
| *b | Bolt |
| *c | No. 2 Check Valve |
| *d | Union Bolt |
Remove the 4 injector hollow screws and 4 gaskets.
Remove the bolt.
Remove the No. 2 check valve from the fuel tube and No. 1 nozzle leakage pipe.
Remove the union bolt and No. 1 nozzle leakage pipe.
When removing the nozzle leakage pipe, place a cushion under the pipe.
Be careful not to deform or scratch the union seal surface.
After removing the nozzle leakage pipe, put it in a plastic bag to prevent foreign matter from contaminating its injector inlet.
12.REMOVE FUEL INJECTOR RH
Remove the 4 bolts, 4 washers, 4 nozzle holder clamps, 4 nozzle holder seals and 4 fuel injectors.
Arrange the fuel injectors, holder clamps, washers and bolts in the correct order.
Remove the O-ring from each fuel injector.
Remove the fuel injector seal from each fuel injector.
Remove the 4 injection nozzle seats from the cylinder head sub-assembly.
23762B 13.REMOVE NO. 2 NOZZLE LEAKAGE PIPE
| *a | Injector Hollow Screw |
| *b | Bolt |
Remove the 4 injector hollow screws and 4 gaskets.
Remove the 2 bolts and No. 2 nozzle leakage pipe.
When removing the nozzle leakage pipe, place a cushion under the pipe.
Be careful not to deform or scratch the union seal surface.
After removing the nozzle leakage pipe, put it in a plastic bag to prevent foreign matter from contaminating its injector inlet.
14.REMOVE FUEL INJECTOR LH
Remove the 4 bolts, 4 washers, 4 nozzle holder clamps, 4 nozzle holder seals and 4 fuel injectors.
Arrange the fuel injectors, holder clamps, washers and bolts in the correct order.
Remove the O-ring from each fuel injector.
Remove the fuel injector seal from each fuel injector.
Remove the 4 injection nozzle seats from the cylinder head sub-assembly.