Home › Engine / Hybrid System › 1VD-FTV (INTAKE / EXHAUST) › INTAKE MANIFOLD (w/ DPF) › 2016.08–2022.09
RM25T0E _51 Engine / Hybrid System _029894 1VD-FTV INTAKE / EXHAUST _0290060 INTAKE MANIFOLD(w/ DPF) A

1VD-FTV INTAKE / EXHAUST  INTAKE MANIFOLD(w/ DPF)  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 51442 3.REMOVE NO. 2 ENGINE UNDER COVER

Hide 87246A 5.DISCONNECT HEATER WATER HOSE

Hide 17940D 6.REMOVE INTERCOOLER ASSEMBLY

Hide 26100G 9.REMOVE DIESEL THROTTLE BODY ASSEMBLY (for Bank 1)

Hide 26100G 10.REMOVE DIESEL THROTTLE BODY ASSEMBLY (for Bank 2)

Hide 15301 11.REMOVE ENGINE OIL LEVEL DIPSTICK

Hide 12142 12.REMOVE NO. 2 ENGINE OIL LEVEL DIPSTICK GUIDE

a.
A391796

Remove the bolt and No. 2 engine oil level dipstick guide.


b.

Remove the O-ring from the No. 2 engine oil level dipstick guide.


Hide 23271H 13.DISCONNECT NO. 1 AND NO. 2 FUEL HOSES

Hide 44769 14.REMOVE VACUUM RESERVOIR CONNECT TUBE

A391798

a.

Slide the 2 clamps and disconnect the 2 vacuum hoses.


b.

Remove the 4 bolts and vacuum reservoir connect tube.


Hide 82122 15.DISCONNECT NO. 2 ENGINE WIRE

A391831

a.

Remove the 3 bolts and disconnect the No. 2 engine wire.


Hide 44761 16.REMOVE VACUUM PUMP TO CONNECTOR TUBE

A391830

a.

Disconnect the engine wire clamp.


b.

Disconnect the No. 2 vacuum transmitting hose assembly.


c.

Slide the 2 clamps and disconnect the 2 vacuum hoses.


d.

Remove the 3 bolts and vacuum pump to connector tube.


Hide 25850 17.REMOVE ELECTRIC VACUUM REGULATING VALVE ASSEMBLY

a.
A391828

Disconnect the electric vacuum regulating valve connector.


b.

Disconnect the 2 vacuum hoses.


c.

Remove the 2 bolts and electric vacuum regulating valve assembly.


Hide 16288 18.REMOVE NO. 4 WATER BY-PASS PIPE

A391829

a.

Slide the 3 clamps and disconnect the inlet water hose, No. 4 water by-pass hose and No. 12 water by-pass hoses.


b.

Remove the 2 bolts, nut and No. 4 water by-pass pipe.


c.

Slide the clamp and remove the No. 2 water by-pass pipe.


Hide 25800 19.REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY

Hide 23243C 20.DISCONNECT FUEL PUMP MOTOR WIRE

a.
A163641

Remove the bolt and No. 1 fuel pump bracket.


b.

Disconnect the fuel pump motor connector.


Hide 82121 21.DISCONNECT ENGINE WIRE

a.
A391794

RH Side:

i.

Disconnect the 6 connectors.


ii.

Disconnect the 4 fuel injector connectors.


iii.

Remove the 4 bolts and nut.


iv.

Detach the 2 clamps and disconnect the engine wire.



b.
A391795

LH Side:

i.

Disconnect the 6 connectors.


ii.

Disconnect the 4 fuel injector connectors.


iii.

Remove the 3 bolts.


iv.

Detach the 2 clamps and disconnect the engine wire.



c.
A391786

Rear Side:

i.

Remove the 2 bolts and disconnect the 2 ground wires.


ii.

Detach the clamp from the No. 3 intercooler support bracket.


iii.

Remove the 2 bolts and disconnect the 2 wire harness brackets.



Hide 23265 22.REMOVE NO. 1 GAS FILTER

a.
A391787

Disconnect the hose from the intake pipe.


b.

Remove the No. 1 gas filter.


Hide 17947B 23.REMOVE NO. 3 INTERCOOLER SUPPORT BRACKET

a.
A391788

Remove the 2 bolts and No. 3 intercooler support bracket.


Hide 23706 24.REMOVE NO. 6 INJECTION PIPE SUB-ASSEMBLY

A391832

NOTICE:

After removing the fuel pipe, to prevent dirt or foreign objects from entering the pipe inlet, cover the common rail with electrical tape. Also protect the injector inlets with electrical tape or plastic bags.


a.

Remove the 2 nuts and 2 injection pipe clamps.


b.

Using a 17 mm union nut wrench, loosen the union nuts and remove the injection pipe.


Hide 25.REMOVE INJECTION PIPE RH

A391789

NOTICE:

After removing the fuel pipe, to prevent dirt or foreign objects from entering the pipe inlet, cover the common rail with electrical tape. Also protect the injector inlets with electrical tape or plastic bags.


a.

Using a 17 mm union nut wrench, loosen the union nuts and remove the 4 injection pipes.


Hide 26.REMOVE INJECTION PIPE LH

A391790

NOTICE:

After removing the fuel pipe, to prevent dirt or foreign objects from entering the pipe inlet, cover the common rail with electrical tape. Also protect the injector inlets with electrical tape or plastic bags.


a.

Using a 17 mm union nut wrench, loosen the union nuts and remove the 4 injection pipes.


Hide 23763 27.REMOVE NO. 3 NOZZLE LEAKAGE PIPE

a.
A395573

Remove the 2 injector hollow screws, 3 bolts, No. 3 nozzle leakage pipe and 2 gaskets.


Hide 23812D 29.REMOVE NO. 2 FUEL PIPE SUB-ASSEMBLY

NOTICE:

After removing an injection pipe, to prevent dirt or foreign objects from entering the common rail holes, cover the holes with protective tape.


a.
A391833

Disconnect the No. 4 fuel hose from the fuel filter to injection pump fuel pipe sub-assembly.


b.

Remove the union bolt and gasket.


c.

Remove the bolt and No. 2 fuel pipe sub-assembly.


Hide 23765 30.REMOVE NO. 5 NOZZLE LEAKAGE PIPE

Hide 23801L 31.REMOVE FUEL FILTER TO INJECTION PUMP FUEL PIPE SUB-ASSEMBLY

a.
A267233

Remove the bolt and No. 2 injection pipe clamp.


b.

Disconnect the fuel hose.


c.

Remove the union bolt, nut, bolt, fuel filter to injection pump fuel pipe sub-assembly and gasket.


Hide 23705 32.REMOVE NO. 5 INJECTION PIPE SUB-ASSEMBLY

a.
A391838

Using a union nut wrench, remove the No. 5 injection pipe.

NOTICE:

After removing an injection pipe, to prevent dirt or foreign objects from entering the common rail hole or injection pump hole, cover the holes with protective tape.



Hide 23820A 33.REMOVE COMMON RAIL RH

Hide 23810A 34.REMOVE COMMON RAIL LH

Hide 17114D 35.REMOVE NO. 3 INTAKE MANIFOLD

A391784

a.

Remove the 16 bolts, 2 gaskets and No. 3 intake manifold.


Hide 23901H 37.REMOVE FUEL TUBE SUB-ASSEMBLY

a.
A392041

Disconnect the 2 fuel tube connectors (See page Engine / Hybrid System>1VD-FTV (FUEL)>FUEL SYSTEM(w/ DPF)>PRECAUTION).


b.

Remove the No. 2 check valve.


c.

Detach the 3 clamps and remove the fuel tube.


Hide 16268 38.REMOVE NO. 1 WATER BY-PASS PIPE

A392042

a.

Remove the union bolt and gasket.


b.

Remove the bolt and No. 1 water by-pass pipe.


Hide 23841C 39.REMOVE NO. 1 FUEL PIPE CLAMP

a.
A267241C01
0.083,0.083 0.375,0.333 0.292,0.25 10 true *a 0.083,2.521 0.271,2.677 0.188,0.156 10 false *b
*a RH Side
*b LH Side


Remove the 2 bolts and 2 No. 1 fuel pipe clamps.


Hide 40.REMOVE STARTER HOSE BRACKET SUB-ASSEMBLY

a.
A287055

Disconnect the 2 starter hoses from the starter assembly and starter hose bracket sub-assembly.


b.
A395574

Remove the 2 bolts and starter hose bracket sub-assembly.


Hide 17111 41.REMOVE NO. 1 INTAKE MANIFOLD

a.
A395575

Remove the 8 bolts, No. 1 intake manifold and gasket.


Hide 17112 42.REMOVE NO. 2 INTAKE MANIFOLD

A164180

a.

Remove the 9 bolts, No. 2 intake manifold and gasket.


Hide 43.REPLACE STUD BOLT

HINT:

If a stud bolt is deformed or its threads are damaged, replace it.


a.
A392047C01
0.719,0.323 1.115,0.323 1.115,0.323 1.521,0.74 true 1.125,0.323 1.188,0.552 false 0.542,0.229 0.854,0.385 0.313,0.156 10 false *1 2.396,0.885 2.708,1.042 0.313,0.156 10 false *a 3.177,0.802 3.375,1.052 0.198,0.25 10 false *b 3.198,1.271 3.385,1.531 0.188,0.26 10 false *c
*1 Stud Bolt
*a 42 mm (1.65 in.)
*b 20 mm (0.787 in.)
*c 13 mm (0.512 in.)


For No. 3 Intake Manifold:

i.

Using an E8 "TORX" wrench, replace the stud bolts.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)



Hide 44.REPLACE RING PIN

HINT:

It is not necessary to remove a ring pin unless it is being replaced.


a.
A177321C01
1,2.656 1.313,2.813 0.313,0.156 10 false *a
*a Protrusion height


For No. 1 and No. 2 Intake Manifold:

Replace the ring pins.

Standard protrusion:

4.4 to 5.6 mm (0.173 to 0.222 in.)