Home › Engine / Hybrid System › 1VD-FTV (FUEL) › FUEL SUPPLY PUMP (w/ DPF) › 2016.08–2022.09
RM25T0E _51 Engine / Hybrid System _029770 1VD-FTV FUEL _0290475 FUEL SUPPLY PUMP(w/ DPF) A

1VD-FTV FUEL  FUEL SUPPLY PUMP(w/ DPF)  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

When replacing the injectors (including shuffling the injectors between the cylinders), common rail, cylinder head or intake manifold, it is necessary to replace the injection pipes with new ones.

·

When fuel lines are disconnected, air may enter the fuel lines, leading to engine starting trouble. Therefore, perform forced regeneration and bleed the air from the fuel lines.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, watching time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 11324 6.REMOVE TIMING CHAIN COVER PLATE

A174824

a.

Remove the 4 bolts, timing chain cover plate and gasket.


Hide 23811G 7.REMOVE NO. 1 FUEL PIPE

A392179

a.

Remove the union bolt, No. 1 fuel pipe and 2 gaskets from the fuel supply pump.


Hide 22100 8.REMOVE FUEL SUPPLY PUMP

a.
A181384

Disconnect the fuel temperature sensor connector.


b.
A164270N03
0.813,2.542 0.813,2.927 true 0.698,2.938 1.031,3.115 0.333,0.177 10 true SST

Using SST, fix the crankshaft pulley in place. Then remove the set nut.

SST
09960-10010  (09962-01000, 09963-01000)


c.
A392180C01
2.333,0.24 2.531,0.396 0.198,0.156 10 true *a 2.271,1.583 2.458,1.74 0.188,0.156 10 true *b 0.729,1.135 0.917,1.292 0.188,0.156 10 true *b
*a Bolt
*b Nut


Using a 6 mm hexagon wrench, remove the bolt.


d.

Loosen the 2 nuts.


e.
A181383C01
2.156,3.354 1.104,3.354 true 2.104,0.938 1.719,0.938 true 2.448,2.698 2.792,2.563 true 1.99,3.802 0.938,3.802 true 2.104,0.302 1.698,0.708 true 2.042,0.146 2.271,0.323 0.229,0.177 10 true *1 2.135,0.854 2.5,1.052 0.365,0.198 10 true SST 2.781,2.438 2.958,2.615 0.177,0.177 10 false *1 0.917,3.25 1.094,3.406 0.177,0.156 10 false *a 0.76,3.708 0.938,3.865 0.177,0.156 10 false *a
*1 SST (No. 1 adapter)
*a Service Hole


Disconnect the pump from the supply pump drive gear.

i.

Install SST (No. 1 adapter) to the timing chain cover.

SST
09950-50013  (09951-05010, 09952-05010, 09953-05020, 09954-05031)

NOTICE:

Do not use any tools in this procedure.



ii.

Rotate the supply pump gear so that the service holes are aligned with SST (No. 1 adapter) as shown in the illustration.


iii.

Using SST, disconnect the pump from the supply pump drive gear.

NOTICE:
·

When removing or installing SST, do not push the supply pump gear.

·

Apply lubricant to the threads and tip of SST (center bolt) before using it.





f.
A392183

Remove the 2 nuts.

NOTICE:
·

Do not hold the supply pump by the parts indicated by the arrows in the illustration, as this may result in deformation, damage and fuel leakage.

·

The supply pump must be kept horizontal.


A392181C01
0.708,0.531 1.292,0.677 true 2.198,0.698 2.854,0.542 true 2.323,1.208 2.563,0.917 true 2.677,1.521 3,1.625 true 1.667,1.854 1.229,2.396 true 6.26,1.969 6.573,1.969 true 0.552,0.438 0.865,0.594 0.313,0.156 10 false *1 2.865,0.427 3.177,0.583 0.313,0.156 10 false *2 1.115,2.375 1.427,2.531 0.313,0.156 9 false *a 6.583,1.865 6.896,2.021 0.313,0.156 10 false *b 3.031,1.552 3.344,1.708 0.313,0.156 10 false *a 2.521,0.75 2.833,0.906 0.313,0.156 10 false *a
*1 Fuel Temperature Sensor *2 Suction Control Valve
*a Fuel Pipe *b Drive Shaft




g.

Remove the O-ring from the supply pump.