Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR AXLE HUB BOLT › from 2016.08
RM25T0E _52 Drivetrain _029907 AXLE AND DIFFERENTIAL _0138020 REAR AXLE HUB BOLT A

AXLE AND DIFFERENTIAL  REAR AXLE HUB BOLT  REPLACEMENT  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.REMOVE REAR WHEEL

Hide 2.REMOVE REAR DISC BRAKE CYLINDER ASSEMBLY LH (for Disc Type)

a.
C271675

Remove the 2 bolts and rear disc brake cylinder assembly.


Hide 42431 3.REMOVE REAR DISC (for Disc Type)

Hide 42403 4.REMOVE REAR BRAKE DRUM SUB-ASSEMBLY (for Drum Type)

Hide 42312E 5.REMOVE REAR AXLE HUB BOLT LH

a.
C305883C02
2.354,1.031 2.594,0.656 2.594,0.656 2.875,0.656 true 1.427,1.604 0.302,1.604 0.302,1.604 1.292,1.104 true 0.125,1.563 0.438,1.719 0.313,0.156 10 false *1 2.823,1.594 3.135,1.75 0.313,0.156 10 false *a 1.198,1.958 1.51,2.115 0.313,0.156 10 false *b 2.958,0.604 3.313,0.802 0.354,0.198 10 false SST
*1 Nut
*a Turn
*b Hold


Temporarily install 2 nuts to the hub bolts as shown in the illustration.


b.

Using SST and a brass bar or equivalent to hold the axle shaft, remove the hub bolt.

SST
09650-17011  


Hide 42312E 6.INSTALL REAR AXLE HUB BOLT LH

a.
C305884C02
3.156,1.958 3.156,1.74 3.156,1.74 3.094,1.656 true 2.833,1.26 2.833,0.365 2.833,0.365 3.031,0.365 true 1.156,1.281 0.333,1.438 0.333,1.438 1.052,0.927 true 0.146,1.396 0.458,1.552 0.313,0.156 10 false *1 3.083,0.25 3.396,0.406 0.313,0.156 10 false *2 2.156,1.115 2.469,1.271 0.313,0.156 10 false *a 0.99,1.635 1.302,1.792 0.313,0.156 10 false *b 3.052,2 3.365,2.156 0.313,0.156 10 false *1
*1 Nut
*2 Washer
*a Turn
*b Hold


Install a plate washer and nut to a new hub bolt as shown in the illustration.


b.

Using a brass bar or equivalent to hold the axle shaft, install the hub bolt by tightening the nut.


c.

Remove the 2 nuts from the hub bolts.


Hide 42431 7.INSTALL REAR DISC (for Disc Type)

Hide 8.INSTALL REAR DISC BRAKE CYLINDER ASSEMBLY LH (for Disc Type)

a.

Install the rear disc brake cylinder assembly with the 2 bolts.

Torque:
100 N*m (1020 kgf*cm, 74 ft.*lbf)


Hide 42403 9.INSTALL REAR BRAKE DRUM SUB-ASSEMBLY (for Drum Type)

Hide 10.ADJUST REAR BRAKE SHOE (for Drum Type)

Hide 11.INSTALL REAR WHEEL