Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2016.08
RM25T0E _51 Engine / Hybrid System _029758 1GR-FE ENGINE CONTROL _0135343 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0443  Evaporative Emission Control System Purge Control Valve Circuit  


DESCRIPTION

To reduce HC emissions, evaporated fuel from the fuel tank is routed through a charcoal canister to the intake manifold for combustion in the cylinders.

The ECM changes the duty signals to the purge VSV so that the intake amount of HC emissions is appropriate for driving conditions (engine load, engine speed, vehicle speed, etc.) after the engine is warmed up.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0443 Evaporative Emission Control System Purge Control Valve Circuit Both of the following conditions (a) and (b) are met (1 trip detection logic):

(a) The target control value and actual control value do not match for 10 seconds or more.

(b) The target control value and actual control value do not match for 80 times or more.


·

Open or short in purge VSV circuit

·

Purge VSV

·

ECM


Comes on DTC stored

WIRING DIAGRAM

A182400E13
5.719,3.219 6.073,3.406 0.354,0.188 10 false ECM 5.573,2.344 5.813,2.531 0.24,0.188 10 false E1 5.208,1.156 5.531,1.323 0.323,0.167 10 false 108 5.583,1.26 5.948,1.448 0.365,0.188 10 false PRG 3.729,1.76 4.448,2.021 0.719,0.26 10 false Purge VSV 3.729,1.604 4.167,1.781 0.438,0.177 10 false C104 4.438,1.146 4.563,1.333 0.125,0.188 10 false 2 5.281,2.219 5.563,2.406 0.281,0.188 10 false 81 3.646,1.146 3.76,1.313 0.115,0.167 10 false 1 2.25,1.417 2.979,1.615 0.729,0.198 10 false EFI NO. 2 0.646,1.25 1.656,1.594 1.01,0.344 10 false from EFI MAIN Relay 5.719,3.031 6.688,3.208 0.969,0.177 10 false C39

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE VSV FOR EVAP CONTROL)
a.
A225197C02
2.583,1.844 0.406,0.708 true 1.688,0.708 1.063,0.25 true 0.854,0.177 1.031,0.344 0.177,0.167 10 *1 0.208,0.615 0.385,0.781 0.177,0.167 10 *2
*1 Purge VSV
*2 Fuel Vapor Feed Hose Assembly (to Canister)


Connect the GTS to the DLC3.


b.

Remove the vacuum hose of the purge VSV from the canister.


c.

Start the engine and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Evap Control.

Powertrain > Engine and ECT > Active Test
Tester Display
Activate the VSV for Evap Control
50004 234 6

e.

When the purge VSV is operated using the GTS, check whether the disconnected hose applies suction to your finger.

OK:
GTS Operation Specified Condition
VSV is ON Disconnected hose applies suction to finger
VSV is OFF Disconnected hose applies no suction to finger



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT PURGE VSV (RESISTANCE)
2.INSPECT PURGE VSV (RESISTANCE)

Result:
Proceed to
OK
NG



OK

3.INSPECT PURGE VSV (POWER SOURCE VOLTAGE)

NG

3.INSPECT PURGE VSV (POWER SOURCE VOLTAGE)
a.
A182261C03
1.479,1.375 1.927,1.625 0.448,0.25 1.604,2.26 1.167,2.615 true 0.219,0.365 0.49,0.573 0.271,0.208 10 false *a 1.542,1.427 1.927,1.646 0.385,0.219 10 false C104 0.958,2.667 1.271,2.865 0.313,0.198 10 false +B
*a Front view of wire harness connector
(to Purge VSV)


Disconnect the purge VSV connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C104-1 - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (PURGE VSV - EFI MAIN)

4.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM)
a.

Disconnect the purge VSV connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C104-2 - C39-108 (PRG) Always Below 1 Ω
C104-2 or C39-108 (PRG) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR