Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › 2017.01–2021.07
RM25T0E _53 Suspension _062777 TIRE PRESSURE MONITORING _0306275 TIRE PRESSURE WARNING SYSTEM J

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  Tire Pressure Warning Light Circuit  


DESCRIPTION

If the tire pressure warning ECU and receiver detects a disconnected connector or an open circuit between the tire pressure warning ECU and receiver and combination meter assembly, the tire pressure warning light blinks for 1 minute, and then remains on after the ignition switch is turned to on.

WIRING DIAGRAM

C171956E22
5.604,0.875 5.75,1.042 0.146,0.167 10 false 5 5.906,1.021 6.302,1.198 0.396,0.177 10 false IND 5.375,1.802 7.156,2.281 1.781,0.479 10 false Tire Pressure Warning ECU and Receiver 1.563,0.833 1.813,0.99 0.25,0.156 10 false 5 0.354,1.875 2.302,2.198 1.948,0.323 10 false Combination Meter Assembly 5.375,1.563 6.927,1.771 1.552,0.208 10 false S30*1, Y7*2, U5*3 0.354,1.677 0.667,1.865 0.313,0.188 10 false L25 1.052,0.99 1.417,1.156 0.365,0.167 10 false TIRE 2.854,1.708 4.26,1.875 1.406,0.167 10 false *1: for Single Cab 2.865,2.031 5.615,2.229 2.75,0.198 10 false *2: for Double Cab 2.885,2.344 5.26,2.563 2.375,0.219 10 false *3: except Single and Double Cabs

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the tire pressure warning ECU and receiver, read the transmitter IDs stored in the old ECU using the GTS and write them down before removal.

·

It is necessary to perform initialization Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION after registration Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION of the transmitter IDs into the tire pressure warning ECU and receiver if the ECU has been replaced.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - TIRE PRESSURE WARNING ECU AND RECEIVER)
a.

Turn the ignition switch off.


b.

Disconnect the S30*1, Y7*2 or U5*3 tire pressure warning ECU and receiver connector.

*1: for Single Cab

*2: for Double Cab

*3: except Single and Double Cabs



c.

Disconnect the L25 combination meter assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S30-5 (IND) - L25-5 (TIRE)*1
Y7-5 (IND) - L25-5 (TIRE)*2
U5-5 (IND) - L25-5 (TIRE)*3
Always Below 1 Ω
S30-5 (IND) or L25-5 (TIRE) - Body ground*1
Y7-5 (IND) or L25-5 (TIRE) - Body ground*2
U5-5 (IND) or L25-5 (TIRE) - Body ground*3
Always 10 kΩ or higher


*1: for Single Cab

*2: for Double Cab

*3: except Single and Double Cabs



Result:
Proceed to
OK
NG



OK

2.CHECK OPERATION OF TIRE PRESSURE WARNING LIGHT (ACTIVE TEST)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK OPERATION OF TIRE PRESSURE WARNING LIGHT (ACTIVE TEST)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / Combination Meter / Active Test.


f.

Check the condition of the tire pressure warning light by using the GTS.

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Indicat. Tire Pressure Warning System Tire pressure warning light OFF or ON Confirm that the vehicle is stopped with the engine idling.
Body Electrical > Combination Meter > Active Test
Tester Display
Indicat. Tire Pressure Warning System
50004 122 57
OK:

The tire pressure warning light turns on or off in accordance with the GTS operation.


Result:
Proceed to
OK
NG




OK

NG