Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › 2017.01–2021.07
RM25T0E _53 Suspension _062777 TIRE PRESSURE MONITORING _0306275 TIRE PRESSURE WARNING SYSTEM J

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  ECU Power Source Circuit  


DESCRIPTION

This is the power source for the tire pressure warning ECU and receiver.

WIRING DIAGRAM

C252619E17
1,0.563 3.292,0.76 2.292,0.198 10 false from IG1 Circuit 3.51,0.74 4.771,1 1.26,0.26 10 false ECU IG 5.156,0.563 5.469,0.76 0.313,0.198 10 false IG 4.927,0.458 5.26,0.656 0.333,0.198 10 false 1 5.135,1.292 6.667,1.49 1.531,0.198 10 false GND 4.875,1.125 5.208,1.323 0.333,0.198 10 false 12 4.333,1.719 6.167,1.917 1.833,0.198 10 false S30*1, Y7*2, U5*3 4.333,1.917 6.906,2.281 2.573,0.365 10 false Tire Pressure Warning ECU and Receiver 0.469,1.698 3.219,1.896 2.75,0.198 10 false *1: for Single Cab 0.49,2.01 3.24,2.208 2.75,0.198 10 false *2: for Double Cab 0.479,2.323 2.865,2.552 2.385,0.229 10 false *3: except Single and Double Cabs

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the tire pressure warning ECU and receiver, read the transmitter IDs stored in the old ECU using the GTS and write them down before removal.

·

It is necessary to perform initialization Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION after registration Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION of the transmitter IDs into the tire pressure warning ECU and receiver if the ECU has been replaced.



HINT:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ECU - BATTERY AND BODY GROUND)
a.

Turn the ignition switch off.


b.
E198671C40
0.219,1.188 0.635,1.458 0.417,0.271 0.219,0.823 0.635,1.094 0.417,0.271 0.219,0.49 0.635,0.76 0.417,0.271 1.24,1.427 0.5,1.583 0.5,1.583 0.5,1.75 true 2.063,1.625 2.49,1.667 true 0.083,0.083 0.396,0.281 0.313,0.198 10 false *a 0.448,1.771 0.76,1.969 0.313,0.198 10 false IG 2.573,1.594 3.313,1.771 0.74,0.177 10 false GND 0.302,1.229 0.76,1.427 0.458,0.198 10 false U5 0.292,0.885 0.75,1.083 0.458,0.198 10 false Y7 0.271,0.542 0.729,0.74 0.458,0.198 10 false S30 0.688,0.542 1,0.74 0.313,0.198 10 false *A 0.667,0.854 0.979,1.052 0.313,0.198 10 false *B 0.688,1.25 1,1.448 0.313,0.198 10 false *C
*A for Single Cab
*B for Double Cab
*C except Single and Double Cabs
*a Front view of wire harness connector
(to Tire Pressure Warning ECU and Receiver)


Disconnect the S30*1, Y7*2 or U5*3 tire pressure warning ECU and receiver connector.

*1: for Single Cab

*2: for Double Cab

*3: except Single and Double Cabs



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
S30-1 (IG) - Body ground*1
Y7-1 (IG) - Body ground*2
U5-1 (IG) - Body ground*3
Ignition switch ON 10 to 16 V
Ignition switch off Below 1 V


*1: for Single Cab

*2: for Double Cab

*3: except Single and Double Cabs



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S30-12 (GND) - Body ground*1
Y7-12 (GND) - Body ground*2
U5-12 (GND) - Body ground*3
Always Below 1 Ω


*1: for Single Cab

*2: for Double Cab

*3: except Single and Double Cabs


Result:
Proceed to
OK
NG




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR