Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › 2017.01–2021.07
RM25T0E _53 Suspension _062777 TIRE PRESSURE MONITORING _0306275 TIRE PRESSURE WARNING SYSTEM C

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  C2198/98  Initialization Switch (for Test Mode DTC)  


DESCRIPTION

During test mode, when the tire pressure warning reset switch is on, the tire pressure warning light comes on and when the tire pressure warning reset switch is off, the tire pressure warning light blinks at 0.125 second intervals.

DTC No. Detection Item DTC Detection Condition Trouble Area
C2198/98 Initialization Switch (for Test Mode DTC) Test mode procedure is performed.
·

Tire pressure warning reset switch

·

Wire harness or connector

·

Tire pressure warning ECU and receiver



WIRING DIAGRAM

C249283E44
4.333,3.052 6.833,3.406 2.5,0.354 10 false Tire Pressure Warning ECU and Receiver 1.885,1.563 4.271,1.844 2.385,0.281 10 false Tire Pressure Warning Reset Switch 1.885,1.354 2.365,1.521 0.479,0.167 10 false L56 2.292,0.875 2.396,1.052 0.104,0.177 10 false 2 3.427,0.875 3.531,1.052 0.104,0.177 10 false 1 4.354,2.802 5.75,2.979 1.396,0.177 10 false S30*1, Y7*2, U5*3 5.229,0.844 5.344,1 0.115,0.156 10 false 7 5.448,1.021 5.885,1.177 0.438,0.156 10 false CLSW 2.51,0.865 2.708,1.083 0.198,0.219 10 false E 3.104,0.865 3.375,1.125 0.271,0.26 10 false INT 1.521,2.646 4.271,2.844 2.75,0.198 10 false *1: for Single Cab 1.542,2.969 4.292,3.167 2.75,0.198 10 false *2: for Double Cab 1.542,3.302 3.906,3.573 2.365,0.271 10 false *3: except Single and Double Cabs

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the tire pressure warning ECU and receiver, read the transmitter IDs stored in the old ECU using the GTS and write them down before removal.

·

It is necessary to perform initialization Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION after registration Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION of the transmitter IDs into the tire pressure warning ECU and receiver if the ECU has been replaced.



PROCEDURE

1.INSPECT TIRE PRESSURE WARNING RESET SWITCH
a.

Turn the ignition switch off.


b.

Remove the tire pressure warning reset switch.

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING RESET SWITCH>REMOVAL


c.

Inspect the tire pressure warning reset switch.

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING RESET SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (TIRE PRESSURE WARNING RESET SWITCH - TIRE PRESSURE WARNING ECU AND RECEIVER)

NG

REPLACE TIRE PRESSURE WARNING RESET SWITCH

2.CHECK HARNESS AND CONNECTOR (TIRE PRESSURE WARNING RESET SWITCH - TIRE PRESSURE WARNING ECU AND RECEIVER)
a.

Disconnect the L56 tire pressure warning reset switch connector.


b.

Disconnect the S30*1, Y7*2 or U5*3 tire pressure warning ECU and receiver connector.

*1: for Single Cab

*2: for Double Cab

*3: except Single and Double Cabs



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S30-7 (CLSW) - L56-1 (INT)*1
Y7-7 (CLSW) - L56-1 (INT)*2
U5-7 (CLSW) - L56-1 (INT)*3
Always Below 1 Ω
S30-7 (CLSW) or L56-1 (INT) - Body ground*1
Y7-7 (CLSW) or L56-1 (INT) - Body ground*2
U5-7 (CLSW) or L56-1 (INT) - Body ground*3
Always 10 kΩ or higher
L56-2 (E) - Body ground Always Below 1 Ω


*1: for Single Cab

*2: for Double Cab

*3: except Single and Double Cabs


Result:
Proceed to
OK
NG




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR