There may be a short circuit between the CAN bus lines when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 53 Ω.
| Symptom | Trouble Area |
|---|---|
| The resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 53 Ω. |
·
Short between CAN bus lines
·
ECM
·
Brake actuator assembly (skid control ECU)
·
Spiral with sensor cable sub-assembly (steering angle sensor)
·
Airbag sensor assembly
·
Combination meter assembly
·
No. 6 CAN junction connector
·
DLC3 CAN branch wire or connector |
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the Precaution in the SRS.
When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the infomation stored in it will not match the infomation from the vehicle and a DTC may be stored.
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.
Disconnect the No. 6 CAN junction connectors.
| *1 | No. 6 CAN Junction Connector | - | - |
| *a | Rear view of wire harness connector (to No. 6 CAN Junction Connector) |
- | - |
| No. 6 CAN Junction Connector | Wiring Color | Connect to |
|---|---|---|
| I119-1 (CANH) | G | Combination meter assembly |
| I119-2 (CANL) | W | |
| I120-1 (CANH) | L | DLC3 |
| I120-2 (CANL) | W | |
| I121-1 (CANH) | R | Spiral with sensor cable sub-assembly (steering angle sensor) |
| I121-2 (CANL) | W | |
| I122-1 (CANH) | G | ECM |
| I122-2 (CANL) | W | |
| I123-1 (CANH) | P | Airbag sensor assembly |
| I123-2 (CANL) | W | |
| I124-1 (CANH) | B | Brake actuator assembly (skid control ECU) |
| I124-2 (CANL) | W |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connect to |
|---|---|---|---|
| I119-1 (CANH) - I119-2 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | Combination meter assembly |
| I120-1 (CANH) - I120-2 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | DLC3 |
| I121-1 (CANH) - I121-2 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Spiral with sensor cable sub-assembly (steering angle sensor) |
| I122-1 (CANH) - I122-2 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | ECM |
| I123-1 (CANH) - I123-2 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Airbag sensor assembly |
| I124-1 (CANH) - I124-2 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Brake actuator assembly (skid control ECU) |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (to Combination meter assembly CAN main wire) | B |
| NG (to ECM CAN main wire) | C |
| NG (to DLC3 CAN branch wires) | D |
| NG (ECU or sensor CAN branch wires) | E |
A
B
C
D
E
Reconnect the No. 6 CAN junction connectors.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Front view of wire harness connector (to Combination Meter Assembly) |
Disconnect the combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L26-13 (CANH) - L26-14 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the No. 6 CAN junction connectors.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Front view of wire harness connector (to ECM) |
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I84-41 (CANH) - I84-49 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
for 1GR-FE: Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>ECM>REMOVAL
for 1VD-FTV: Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECM>REMOVAL
NG
| *a | Front view of DLC3 |
Reconnect the CAN junction connector.
Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the short circuited CAN branch wire is connected.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I17-6 (CANH) - I17-14 (CANL) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.
| Proceed to |
|---|
| OK |
| NG |
OK
NG