Steering angle sensor signals are input to the skid control ECU (brake actuator assembly) via the CAN communication system.
When a malfunction occurs in the communication line to the steering angle sensor, U0126 is output.
If a DTC related to the CAN communication line is output, first troubleshoot the CAN communication line.
DTCs may be stored if one of the following occurs:
Steering angle sensor zero point malfunction
Steering angle sensor signal malfunction
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1434 | Steering Angle Sensor Output Malfunction | Normal communication between the skid control ECU and the steering angle sensor and abnormal steering angle sensor zero point. |
·
ECU-B fuse
·
ECU IG fuse
·
Steering angle sensor (Spiral with sensor cable sub-assembly)
·
Skid control ECU (Brake actuator assembly)
·
Wire harness or connector |
Refer to DTC C1432.
Do not remove the steering angle sensor from the spiral with sensor cable sub-assembly.
When replacing the steering angle sensor (spiral with sensor cable sub-assembly), confirm that the replacement part is of the correct specification.
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
When U0073, U0124 and/or U0126 is output together with C1434, inspect and repair the trouble areas indicated by U0073, U0124 and/or U0126 first.
When any of the speed sensors or the yaw rate and acceleration sensor (airbag sensor assembly) has trouble, DTCs for the steering angle sensor (spiral with sensor cable sub-assembly) may be output even when the steering angle sensor (spiral with sensor cable sub-assembly) is normal. When DTCs for the speed sensors or yaw rate and acceleration sensor (airbag sensor assembly) are output together with DTCs for the steering angle sensor (spiral with sensor cable sub-assembly), inspect and repair the speed sensor and yaw rate and acceleration sensor (airbag sensor assembly) first, and then inspect and repair the steering angle sensor (spiral with sensor cable sub-assembly).
Turn the ignition switch off.
Turn the ignition switch to ON again and check that no CAN communication system DTC is output.
for LHD: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for LHD with VSC)>DIAGNOSIS SYSTEM
for RHD: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for RHD with VSC)>DIAGNOSIS SYSTEM
Start the engine.
Drive the vehicle at a speed of 35 km/h (22 mph) and turn the steering wheel to the right and left to check that no speed sensor or yaw rate and acceleration sensor DTCs are output.
If there is a malfunction in any of the speed sensors or the yaw rate and acceleration sensor (airbag sensor assembly), an abnormal value may be output although the steering angle sensor (spiral with sensor cable sub-assembly) sensor is normal.
If speed sensor and yaw rate and acceleration sensor (airbag sensor assembly) DTCs are output simultaneously, repair these two sensors first and inspect the steering angle sensor (spiral with sensor cable sub-assembly).
| Result | Proceed to |
|---|---|
| No CAN communication system, speed sensor, or yaw rate and acceleration sensor DTCs are output | A |
| CAN communication system DTC is output | B |
| Speed sensor or yaw rate and acceleration sensor DTC is output | C |
A
B
for LHD: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for LHD with VSC)>HOW TO PROCEED WITH TROUBLESHOOTING
for RHD: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for RHD with VSC)>HOW TO PROCEED WITH TROUBLESHOOTING
C
Turn the ignition switch off.
Remove the steering wheel and the column cover lower.
Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY>REMOVAL
| *a | Front view of wire harness connector (to Steering Angle Sensor [Spiral with Sensor Cable Sub-assembly]) |
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
Disconnect the L47 steering angle sensor (spiral with sensor cable sub-assembly) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L47-6 (BAT) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch to ON.
| *a | Front view of wire harness connector (to Steering Angle Sensor [Spiral with Sensor Cable Sub-assembly]) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| L47-5 (IG) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
| *a | Front view of wire harness connector (to Steering Angle Sensor [Spiral with Sensor Cable Sub-assembly]) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L47-2 (ESS) - Body ground | Always | Below 1 Ω |
If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step.
| Proceed to |
|---|
| OK |
| NG |
OK
NG