Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o EGR System) › 2017.01–2017.09
RM25T0E _51 Engine / Hybrid System _029760 1VD-FTV ENGINE CONTROL _0309414 ECD SYSTEM(w/o EGR System) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/o EGR System)  P007C  Charge Air Cooler Temperature Sensor Circuit Low  P007D  Charge Air Cooler Temperature Sensor Circuit High  


DESCRIPTION

A283580E06
3.354,2.271 3.74,1.99 false 2.26,0.406 2.833,0.667 0.573,0.26 10 Fig. 1: 3.292,4.271 4.167,4.5 0.875,0.229 10 Temperature 2.396,0.969 2.771,1.219 0.375,0.25 10 (kΩ) 2.281,1.146 2.521,1.365 0.24,0.219 10 30 2.281,1.583 2.521,1.802 0.24,0.219 10 10 2.354,1.875 2.594,2.094 0.24,0.219 10 5 2.354,2.094 2.594,2.313 0.24,0.219 10 3 2.354,2.26 2.51,2.479 0.156,0.219 10 2 2.344,2.531 2.594,2.75 0.25,0.219 10 1 2.24,2.833 2.479,3.052 0.24,0.219 10 0.5 2.24,3.198 2.479,3.417 0.24,0.219 10 0.2 2.24,3.469 2.479,3.688 0.24,0.219 10 0.1 2.281,1.323 2.531,1.542 0.25,0.219 10 20 2.542,3.823 2.781,4.042 0.24,0.219 10 -20 2.938,3.823 3.177,4.042 0.24,0.219 10 0 3.208,3.823 3.448,4.042 0.24,0.219 10 20 3.521,3.823 3.76,4.042 0.24,0.219 10 40 3.833,3.823 4.073,4.042 0.24,0.219 10 60 4.146,3.823 4.385,4.042 0.24,0.219 10 80 4.385,3.823 4.625,4.042 0.24,0.219 10 100 2.583,4 2.823,4.219 0.24,0.219 10 -4 2.896,4 3.135,4.219 0.24,0.219 10 32 3.208,4 3.448,4.219 0.24,0.219 10 68 3.479,4 3.729,4.25 0.25,0.25 10 104 3.792,4 4.125,4.25 0.333,0.25 10 140 4.094,4 4.417,4.25 0.323,0.25 10 176 4.385,4 4.708,4.25 0.323,0.25 10 212 4.677,3.823 5,4.073 0.323,0.25 10 (°C) 4.677,4 5,4.25 0.323,0.25 10 (°F) 3.802,1.896 4.583,2.167 0.781,0.271 10 Acceptable 2.26,0.719 3.083,0.917 0.823,0.198 10 Resistance 2.24,3.021 2.479,3.24 0.24,0.219 10 0.3

The Intake Air Temperature (IAT) sensor detects the IAT after the intake air passes through the intercooler. A built-in thermistor in the sensor changes its resistance value according to the intake air temperature. The lower the intake air temperature, the higher the thermistor resistance value. The higher the intake air temperature, the lower the thermistor resistance value (See Fig. 1).

The sensor is connected to the ECM. The 5 V power source voltage in the ECM is applied to the sensor from terminal THIA via resistor R. Resistor R and the sensor are connected in series. When the resistance value of the sensor changes in accordance with changes in the IAT, the potential at terminal THIA also changes. Based on this signal, the ECM corrects the fuel injection volume to improve driveability with a cold engine.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P007C Charge Air Cooler Temperature Sensor Circuit Low Short in the intake air temperature sensor (turbo) circuit for 0.5 seconds (1 trip detection logic).
·

Short in intake air temperature sensor (turbo) circuit

·

Intake air temperature sensor (turbo)

·

ECM


Comes on DTC stored
P007D Charge Air Cooler Temperature Sensor Circuit High Open in the intake air temperature sensor (turbo) circuit for 0.5 seconds (1 trip detection logic).
·

Open in intake air temperature sensor (turbo) circuit

·

Intake air temperature sensor (turbo)

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P007C Intake Air Temp (Turbo)
P007D

HINT:

If DTC P007C or P007D is stored, the following symptoms may appear:

-

Misfire

-

Combustion noise

-

Black smoke

-

White smoke

-

Lack of power




CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P007C Ignition switch ON for 1 second or more
P007D

WIRING DIAGRAM

A337317E58
0.448,2.813 0.76,3.01 0.313,0.198 10 false C60 5.563,3.01 6.021,3.208 0.458,0.198 10 false C39 5.583,3.208 6.042,3.406 0.458,0.198 10 false ECM 0.438,3.021 2.969,3.24 2.531,0.219 10 false Intake Air Temperature Sensor (Turbo) 5.26,1.333 5.719,1.531 0.458,0.198 10 false THIA 5.26,1.917 5.781,2.115 0.521,0.198 10 false E2 2.198,1.323 2.656,1.521 0.458,0.198 10 false 2 2.208,1.927 2.667,2.125 0.458,0.198 10 false 1 5.01,1.333 5.469,1.531 0.458,0.198 10 false 74 5.021,1.927 5.479,2.125 0.458,0.198 10 false 75 5.906,0.948 6.365,1.146 0.458,0.198 10 false 5 V 5.854,1.219 6.313,1.417 0.458,0.198 10 false R

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR System)>REGISTRATION) and initialization (Click here Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR System)>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (INTAKE AIR TEMPERATURE [TURBO])
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air Temp (Turbo).

Powertrain > Engine and ECT > Data List
Tester Display
Intake Air Temp (Turbo)
50003 61 240

d.

Read the value.

OK:

Same as air temperature near intake manifold


Result:
Result Proceed to
-40°C (-40°F) A
140°C (284°F) or higher B
OK (same as air temperature near intake manifold) C


HINT:
·

If there is an open circuit, the GTS indicates -40°C (-40°F).

·

If there is a short circuit, the GTS indicates 140°C (284°F) or higher.





A

2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)

B

7.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)

C

8.REPLACE INTAKE AIR TEMPERATURE SENSOR (TURBO)
2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)
a.
A239705C06
0.708,1.427 1.021,1.625 0.313,0.198 10 false *1 2.667,1.375 2.979,1.573 0.313,0.198 10 false *2 2.438,0.677 2.979,0.865 0.542,0.188 10 false THIA 2.427,1.042 2.74,1.24 0.313,0.198 10 false E2 1.688,0.698 2.229,0.885 0.542,0.188 10 false THA 1.708,1.073 2.021,1.271 0.313,0.198 10 false E2 0.844,2.781 1.156,2.979 0.313,0.198 10 false *a
*1 Intake Air Temperature Sensor (Turbo)
*2 ECM
*a Front view of wire harness connector
(to Intake Air Temperature Sensor (Turbo))


Disconnect the intake air temperature sensor (turbo) connector.


b.

Connect terminals 1 and 2 of the intake air temperature sensor (turbo) wire harness side connector.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON and turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air Temp (Turbo).

Powertrain > Engine and ECT > Data List
Tester Display
Intake Air Temp (Turbo)
50003 61 240

f.

Read the value.

OK:

140°C (284°F) or higher



g.

Reconnect the intake air temperature sensor (turbo) connector.


Result:
Proceed to
OK
NG



OK

3.CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE INTAKE AIR TEMPERATURE SENSOR (TURBO)

NG

4.CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR - ECM)
3.CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE INTAKE AIR TEMPERATURE SENSOR (TURBO)
a.

Replace the intake air temperature sensor (turbo).

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>INTAKE AIR TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR - ECM)
a.

Disconnect the intake air temperature sensor (turbo) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C60-2 - C39-74 (THIA) Always Below 1 Ω
C60-1 - C39-75 (E2) Always Below 1 Ω



d.

Reconnect the intake air temperature sensor (turbo) connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

5.CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM.

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM.

Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)
a.
A302633C39
0.771,0.25 1.083,0.448 0.313,0.198 10 false *1 2.604,0.25 2.917,0.448 0.313,0.198 10 false *2 2.438,1.031 2.813,1.292 0.375,0.26 10 false THIA 2.479,1.51 3.01,1.813 0.531,0.302 10 false E2
*1 Intake Air Temperature Sensor (Turbo)
*2 ECM


Disconnect the intake air temperature sensor (turbo) connector.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air Temp (Turbo).

Powertrain > Engine and ECT > Data List
Tester Display
Intake Air Temp (Turbo)
50003 61 240

e.

Read the value.

OK:

-40°C (-40°F)



f.

Reconnect the intake air temperature sensor (turbo) connector.


Result:
Proceed to
OK
NG



OK

8.REPLACE INTAKE AIR TEMPERATURE SENSOR (TURBO)

NG

10.CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR (TURBO) - ECM)
8.REPLACE INTAKE AIR TEMPERATURE SENSOR (TURBO)
a.

Replace the intake air temperature sensor (turbo).

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>INTAKE AIR TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 61

c.

Turn the ignition switch off for 30 seconds or more.


d.

Turn the ignition switch to ON for 1 second or more.


e.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


f.

Confirm that the DTC is not output again.

Powertrain > Engine and ECT > Trouble Codes
50001 61

Result:
Proceed to
NEXT



NEXT

END

10.CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR (TURBO) - ECM)
a.

Disconnect the intake air temperature sensor (turbo) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C60-2 or C39-74 (THIA) - Body ground and other terminals Always 10 kΩ or higher



d.

Reconnect the intake air temperature sensor (turbo) connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

11.REPLACE ECM

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
11.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED