The ECM opens and closes the throttle valve using a rotary solenoid type actuator. Due to opening and closing the valve, the exhaust gas recirculation volume can be properly controlled. Also, engine vibration and noise will be reduced by closing the valve when the engine is stopped.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0488 | Exhaust Gas Recirculation Throttle Position Control Range / Performance | When either condition below is met:
·
When throttle valve (for Bank 1) remains closed despite ECM's signal to open valve (1 trip detection logic)
·
When throttle valve (for Bank 1) remains open despite ECM's signal to close valve (1 trip detection logic) |
·
Throttle valve (for Bank 1) stuck
·
Throttle valve (for Bank 1) does not move smoothly
·
Open or short in throttle valve (for Bank 1) circuit
·
ECM |
Comes on | DTC stored |
| P213B | Exhaust Gas Recirculation Throttle Position Control (Range / Performance) | When either condition below is met:
·
When throttle valve (for Bank 2) remains closed despite ECM's signal to open valve (1 trip detection logic)
·
When throttle valve (for Bank 2) remains open despite ECM's signal to close valve (1 trip detection logic) |
·
Throttle valve (for Bank 2) stuck
·
Throttle valve (for Bank 2) does not move smoothly
·
Open or short in throttle valve (for Bank 2) circuit
·
ECM |
Comes on | DTC stored |
| Condition | Throttle Valve Position |
|---|---|
| Moment when accelerator pedal is further depressed or released at 3000 rpm | Opening angle varies smoothly |
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P0488 | Perform the following repeatedly for 1 minute: gradually raise the engine speed to 3000 rpm from idling over approximately 10 seconds, and then release the accelerator pedal to return to an idling state. |
| P213B |
The ECM opens and closes the throttle valve by adjusting the current flowing to the rotary solenoid with a duty ratio. If the throttle valve does not move smoothly or is stuck, the duty ratio used during valve movement control increases or decreases greatly. The ECM will determine that the throttle valve is malfunctioning and the ECM illuminates the MIL.
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR System)>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR System)>INITIALIZATION).
After warming up the engine, DTC P0488 and P213B can be set if 1 second or more passes after quickly accelerating the engine from idling.
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Engine and ECT / Active Test / Diesel Throttle Target Angle or Diesel Throttle Target Angle #2.
| Tester Display |
|---|
| Diesel Throttle Target Angle |
| Tester Display |
|---|
| Diesel Throttle Target Angle #2 |
While continuously changing the Active Test value to 0, 30, 60, 90, 60, 30 and 0%, check that "Actual Throttle Position" or "Actual Throttle Position #2" smoothly changes to the set opening amount.
Value smoothly changes to set opening amount.
| Proceed to |
| OK |
| NG |
OK
NG
Visually check for deposits in the diesel throttle body assembly. If there are deposits, clean the diesel throttle body assembly.
| Proceed to |
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Engine and ECT / Active Test / Diesel Throttle Target Angle or Diesel Throttle Target Angle #2.
| Tester Display |
|---|
| Diesel Throttle Target Angle |
| Tester Display |
|---|
| Diesel Throttle Target Angle #2 |
While continuously changing the Active Test value to 0, 30, 60, 90, 60, 30 and 0%, check that "Actual Throttle Position" or "Actual Throttle Position #2" smoothly changes to the set opening amount.
Value smoothly changes to set opening amount.
| Proceed to |
| OK |
| NG |
OK
NG
Clear the DTCs.
Turn the ignition switch off and wait for 30 seconds.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Start the engine.
Over a period of 10 seconds or more, slowly raise the engine speed to 3000 rpm and lower it.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Display | Proceed to |
|---|---|
| P0488 or P213B is output | A |
| No DTC is output | B |
A
B
Replace the ECM.
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
| NEXT |
NEXT
Connect the GTS to the DLC3.
Clear the DTCs.
Turn the ignition switch off and wait for 30 seconds.
Start the engine.
Over a period of 10 seconds or more, slowly raise the engine speed to 3000 rpm, and then lower it.
Confirm that the DTC is not output again.
Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.
Enter the following menus: Engine and ECT / Utility / All Readiness.
| Tester Display |
|---|
| All Readiness |
Input DTC P0488 and P213B.
Check that STATUS is NORMAL. If STATUS is INCOMPLETE or N/A, over a period of 10 seconds or more, slowly raise the engine speed to 3000 rpm again, and then idle the engine for 5 minutes.
| Proceed to |
| NEXT |
NEXT
When DTC P0488 is output
Replace the diesel throttle body assembly (for bank 1).
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>DIESEL THROTTLE BODY>REMOVAL
When DTC P213B is output
Replace the diesel throttle body assembly (for bank 2).
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>DIESEL THROTTLE BODY>REMOVAL
| Proceed to |
| NEXT |
NEXT
| *A | for Bank 1 |
| *B | for Bank 2 |
| *a | Front view of wire harness connector (to Throttle Control Motor) |
Disconnect the throttle control motor connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C58-2 (VCR) - Body ground | Ignition switch ON | 11 to 14 V |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C61-2 (VCR) - Body ground | Ignition switch ON | 11 to 14 V |
Reconnect the throttle control motor connector.
| Proceed to |
| OK |
| NG |
OK
NG
Disconnect the throttle control motor connector.
Remove the MAIN relay and MAIN2 relay from the engine room relay block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C58-2 (VCR) - MAIN relay terminal 3 | Always | Below 1 Ω |
| C58-2 (VCR) or MAIN relay terminal 3 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C61-2 (VCR) - MAIN2 relay terminal 3 | Always | Below 1 Ω |
| C61-2 (VCR) or MAIN2 relay terminal 3 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
| OK |
| NG |
OK
NG
Disconnect the throttle control motor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C58-1 (VTAR) - C39-42 (LUSL) | Always | Below 1 Ω |
| C58-3 (E2R) - Body ground | Always | Below 1 Ω |
| C58-1 (VTAR) or C39-42 (LUSL) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C61-1 (VTAR) - C39-84 (LUS2) | Always | Below 1 Ω |
| C61-3 (E2) - Body ground | Always | Below 1 Ω |
| C61-1 (VTAR) or C39-84 (LUS2) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
| OK |
| NG |
OK
NG
Repair or replace the harness or connector.
| Proceed to |
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
| NEXT |
NEXT