Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2017.01
RM25T0E _51 Engine / Hybrid System _029758 1GR-FE ENGINE CONTROL _0135343 SFI SYSTEM J

1GR-FE ENGINE CONTROL  SFI SYSTEM  Brake Override System  


DESCRIPTION

w/o VSC

When the vehicle is being driven with the accelerator pedal depressed, depressing the brake pedal without releasing the accelerator pedal will activate the brake override system to restrict driving torque. The conditions for activating the brake override system as well as the items that are controlled are explained below.


w/ VSC

When the vehicle is being driven, depressing the accelerator pedal and brake pedal will activate the brake override system to restrict driving torque. The conditions for activating the brake override system as well as the items that are controlled are explained below.


A308494E21
0.354,0.479 2.531,0.677 2.177,0.198 10 false Accelerator Pedal Position Sensor 0.354,1.271 2.573,1.635 2.219,0.365 10 false Master Cylinder Pressure Sensor (Brake Actuator Assembly)* 0.365,2.531 2.177,2.75 1.813,0.219 10 false Stop Light Switch Assembly 0.375,3.281 1.979,3.802 1.604,0.521 10 false Vehicle Speed Sensor or Wheel Speed Sensor 2.677,0.75 4,1.281 1.323,0.531 10 false Actual Accelerator Pedal Angle 2.833,1.708 4.052,2.469 1.219,0.76 10 false Master Cylinder Pressure* 3.021,2.698 3.667,2.896 0.646,0.198 10 false ON/OFF 2.854,3.719 3.833,3.917 0.979,0.198 10 false Vehicle Speed 5.688,1.854 7.01,2.417 1.323,0.563 10 false Effective Accelerator Pedal Angle for System Control 4.344,0.49 4.99,0.688 0.646,0.198 10 false ECM 5.76,3.896 6.521,4.094 0.76,0.198 10 false *: w/ VSC

Activation Conditions:
w/o VSC
·

Vehicle is running at or above the specified speed.

·

The accelerator pedal is depressed beyond a specified level, and then the brake pedal is depressed.

NOTICE:

The vehicle may not enter the brake override system control due to the relation of the accelerator pedal angle and the vehicle's speed.



w/ VSC
·

When the accelerator pedal and brake pedal are depressed.

NOTICE:

The vehicle may not enter the brake override system control due to the relation of the accelerator pedal angle and the vehicle's speed.




Items Controlled:
w/o VSC
·

Driving torque is restricted.

HINT:

During brake override system control, the value for the accelerator pedal angle (which is used for engine control) is forcibly reduced to a specified value. For this reason, the Data List value for Throttle Sensor Volt % will be replaced with a specified value regardless of the actual accelerator pedal angle (Accel Sens. No. 1 Volt %, Accel Sens. No. 2 Volt %)



w/ VSC
·

When the vehicle speed is extremely low, the accelerator opening value used when controlling the engine is reduced more than normal.

HINT:

During control, the Accelerator Position value in the Data List will be lower than normal.


·

When the vehicle speed is not extremely low, the accelerator opening value is forcibly lowered to a fixed value.

HINT:

During control, the Accelerator Position value in the Data List is forcibly reduced to a specified value regardless of the actual accelerator opening value (Accel Sens. No.1 Volt %).




Deactivation Conditions:
w/o VSC
·

When the stop light switch turns OFF or the actual accelerator pedal angle increases or decreases beyond the specified range.


w/ VSC
·

When the brake pedal or the accelerator pedal returns to some degree.



CAUTION / NOTICE / HINT

Inspection Method

Drive at 10 km/h (6.25 mph), depress the accelerator pedal by 1/2 to 3/4 and keep it in that position. Under these conditions, if the engine speed decreases to 1000 rpm when the brake pedal is depressed, then the brake override system has been activated.


CAUTION:

When carrying out the inspection, use a place where you are able to carry it out safely and also pay close attention to your surroundings.

Also, when driving, make absolutely sure that all road traffic laws, such as speed limits, are observed.


HINT:
w/o VSC
·

Under normal conditions, the Throttle Sensor Volt % value changes in response to the Accel Sens. No. 1 Volt % value. For more information on the numerical values, refer to the Data List (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST).

·

If the Data List values of Throttle Sensor Volt % and Accel Sens. No. 1 Volt % do not match, and the value of Accelerator Position changes but the value of Accel Sens. No. 1 Volt % is constant, this confirms that brake override system has activated. (Data can be captured relatively easily by using the snapshot function in the Data List. Confirm the data after performing the drive test.)


w/ VSC
·

Under normal conditions, the Accelerator Position value changes in response to the Accel Sens. No.1 Volt % value. For more information on the numerical values, refer to the Data List.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST

·

If the Accelerator Position and Accel Sens. No.1 Volt % values in the Data List diverge and the Accelerator Position value in the Data List is fixed even though Accel Sens. No.1 Volt % is changing, check that this control is activated (use the GTS data saving function to record data while driving the vehicle, and then confirm it after driving is completed).



NOTICE:

The brake override system restricts driving torque if the brake pedal is depressed when driving with the accelerator pedal depressed. If a customer reports experiencing loss of torque after the accelerator and brake pedals have both been intentionally depressed, explain to the customer that this is not a malfunction, and that the customer should avoid depressing both the accelerator and brake pedals at the same time.

Example: While operating the accelerator pedal, the customer uses their left foot to operate the brake pedal.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: System Select / Health Check.


d.

Check the DTCs.

Result:
Result Proceed to
DTCs are not output (w/ VSC) A
DTCs are not output (w/o VSC) B
DTCs are output C




A

2.READ VALUE USING GTS (MASTER CYLINDER PRESSURE)

B

3.READ VALUE USING GTS (STOP LIGHT SWITCH AND ST1)

C

2.READ VALUE USING GTS (MASTER CYLINDER PRESSURE)
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List / Master Cylinder Pressure.

Chassis > ABS/VSC/TRC > Data List
Tester Display
Master Cylinder Pressure
50003 105 393

d.

Read the value displayed on the GTS.

Standard:

0 to 1.76 MPa (Brake pedal released).



e.

Check that the brake fluid pressure value of the "Master Cylinder Pressure" observed on the GTS changes when the brake pedal is depressed.

OK:

When the pedal is depressed, the pressure displayed on the GTS increases.



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (STOP LIGHT SWITCH AND ST1)

NG

3.READ VALUE USING GTS (STOP LIGHT SWITCH AND ST1)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Ptrl Throttle / Stop Light Switch and ST1.

Powertrain > Engine and ECT > Data List
Tester Display
Stop Light Switch
50003 234 117

e.

Check the Data List indication when the brake pedal is depressed and released.

OK:
GTS Display Condition Specified Condition
Stop Light Switch Brake pedal released OFF
Brake pedal depressed ON
ST1 Brake pedal released OFF
Brake pedal depressed ON



Result:
Proceed to
OK
NG



OK

4.INSPECT BRAKE PEDAL

NG

INSPECT STOP LIGHT SWITCH ASSEMBLY

4.INSPECT BRAKE PEDAL
a.

Inspect and adjust the brake pedal.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL>ADJUSTMENT

HINT:

If the stop light switch turns ON too late, the start of brake override system control may be delayed; if it turns ON too soon, brake override system control may begin too early, so conduct inspection of the brake pedal and stop light switch assembly.



Result:
Proceed to
OK
NG



OK

5.READ VALUE USING GTS (ACCELERATOR PEDAL POSITION SENSOR)

NG

REPAIR OR REPLACE BRAKE PEDAL

5.READ VALUE USING GTS (ACCELERATOR PEDAL POSITION SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Ptrl Throttle / Accel Sens. No.1 Volt % and Accel Sens. No.2 Volt %.

Powertrain > Engine and ECT > Data List
Tester Display
Accel Sens. No.1 Volt %
Accel Sens. No.2 Volt %
50003 234 15,16

e.

Read the value displayed on the GTS.

OK:
GTS Display Condition Specified Condition
Accel Sens. No. 1 Volt % Accelerator Pedal Released → Depressed → Released Values smoothly change following accelerator pedal operation
Accel Sens. No. 2 Volt %


HINT:

For numerical values of Accel Sens. No. 1 Volt % and Accel Sens. No. 2 Volt %, refer to the Data List.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST



Result:
Proceed to
OK
NG



OK

6.READ VALUE USING GTS (VEHICLE SPEED)

NG

REPLACE ACCELERATOR PEDAL(W/SENSOR) ROD ASSEMBLY

6.READ VALUE USING GTS (VEHICLE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Start the engine.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Vehicle Speed.

Powertrain > Engine and ECT > Data List
Tester Display
Vehicle Speed
50003 234 10

f.

Read the value displayed on the GTS.

Standard:
GTS Display Condition Specified Condition
Vehicle Speed Vehicle stopped, engine running 0 km/h (0 mph)
Vehicle being driven at constant speed between 16.1 to 64.4 km/h (10 to 40 mph) No large fluctuations when driving at a constant speed


CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Data can be captured relatively easily by using the snapshot function in the Data List. Confirm the data after performing the drive test.



Result:
Proceed to
OK
NG



OK

7.READ VALUE USING GTS (FR, FL, RR, RL WHEEL SPEED)

NG

7.READ VALUE USING GTS (FR, FL, RR, RL WHEEL SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Start the engine.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List / All Data / FR Wheel Speed, FL Wheel Speed, RR Wheel Speed and RL Wheel Speed.


f.

Read the value displayed on the GTS.

Standard:
GTS Display Condition Specified Condition
FR Wheel Speed
FL Wheel Speed
RR Wheel Speed
RL Wheel Speed
Vehicle stopped, engine running 0 km/h (0 mph)
Vehicle being driven at constant speed between 16.1 to 64.4 km/h (10 to 40 mph) No large fluctuations when driving at a constant speed


CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Data can be captured relatively easily by using the snapshot function in the Data List. Confirm the data after performing the drive test.



Result:
Proceed to
OK
NG



OK

END

NG

INSPECT FRONT OR REAR SPEED SENSOR