Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2017.01
RM25T0E _51 Engine / Hybrid System _029758 1GR-FE ENGINE CONTROL _0135343 SFI SYSTEM J

1GR-FE ENGINE CONTROL  SFI SYSTEM  MIL Circuit  


DESCRIPTION

w/o VSC

The MIL (Malfunction Indicator Lamp) is used to indicate vehicle malfunction detections by the ECM. When the ignition switch is turned to ON, power is supplied to the MIL circuit, and the ECM provides the circuit ground which illuminates the MIL.

The MIL operation can be checked visually: When the ignition switch is first turned to ON, the MIL should be illuminated and should then turn off when the engine is started. If the MIL remains illuminated or is not illuminated, conduct the following troubleshooting procedure using the GTS.


w/ VSC

The MIL (Malfunction Indicator Lamp) is used to indicate vehicle malfunctions detected by the ECM.

The MIL operation can be checked visually. When the ignition switch is first turned to ON, the MIL should be illuminated and should then turn off after the engine is started. If the MIL remains illuminated or is not illuminated, conduct the following troubleshooting procedure using the GTS.


WIRING DIAGRAM

w/o VSC
A182518E07
5.938,2.427 6.896,2.594 0.958,0.167 10 false I84 *1 A29 *2 6.198,2.583 6.594,2.74 0.396,0.156 10 false ECM 6.031,1 6.25,1.156 0.219,0.156 10 false W 5.76,0.99 5.958,1.146 0.198,0.156 10 false 24 4.906,1.115 5.229,1.271 0.323,0.156 10 false L26 4.948,0.927 5.146,1.083 0.198,0.156 10 false 21 2.708,1.104 3.031,1.26 0.323,0.156 10 false L25 2.771,0.906 2.969,1.063 0.198,0.156 10 false 28 3.708,1.281 4,1.448 0.292,0.167 10 false MIL 4.51,1.229 4.844,1.396 0.333,0.167 10 false CHK 3.063,1.229 3.271,1.396 0.208,0.167 10 false B 1.99,1.25 2.344,1.417 0.354,0.167 10 false MET 3.375,2.083 4.625,2.25 1.25,0.167 10 false Combination Meter 0.188,1.104 1.438,1.302 1.25,0.198 10 false from Ignition Switch 4.458,2.74 5.531,2.938 1.073,0.198 10 false *1: for LHD 4.469,2.958 5.542,3.156 1.073,0.198 10 false *2: for RHD

w/ VSC
A385196E02
1.167,3.271 2.927,3.5 1.76,0.229 10 false : CAN Communication Line 0.906,1.958 1.375,2.219 0.469,0.26 10 false L26 2.177,0.729 2.823,0.969 0.646,0.24 10 false CANH 3.521,2.729 4.427,2.938 0.906,0.208 10 false *1: for RHD 5.292,2.031 6.292,2.292 1,0.26 10 false A29*1, I84*2 0.896,2.135 2.875,2.375 1.979,0.24 10 false Combination Meter Assembly 2.177,1.417 2.615,1.656 0.438,0.24 10 false CANL 2.698,0.469 2.979,0.688 0.281,0.219 10 false 13 2.677,1.26 2.958,1.479 0.281,0.219 10 false 14 4.625,0.479 4.833,0.698 0.208,0.219 10 false 41 4.646,1.219 4.854,1.438 0.208,0.219 10 false 49 4.958,0.719 5.604,0.958 0.646,0.24 10 false CANH 4.99,1.354 5.427,1.594 0.438,0.24 10 false CANL 5.563,2.25 6.031,2.49 0.469,0.24 10 false ECM 3.51,3.094 4.51,3.313 1,0.219 10 false *2: for LHD

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK IF VEHICLE IS EQUIPPED WITH VSC
a.

Confirm the vehicle specifications.

Result:
Result Proceed to
w/o VSC A
w/ VSC B




A

2.CHECK THAT MIL IS ILLUMINATED

B

9.CHECK THAT MIL IS ILLUMINATED
2.CHECK THAT MIL IS ILLUMINATED
a.

Check that the MIL is illuminated.

Result:
Result Proceed to
MIL remains ON A
MIL does not illuminate B




A

3.CHECK WHETHER MIL TURNS OFF

B

6.CHECK THAT MIL IS ILLUMINATED
3.CHECK WHETHER MIL TURNS OFF
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Check for DTCs. If DTCs are output, write them down.


d.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Check that the MIL turns off.

OK:

MIL turns off.



Result:
Proceed to
OK
NG



OK

NG

4.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
4.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
a.

Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Check that the MIL is not illuminated.

OK:

MIL is not illuminated.



Result:
Proceed to
OK
NG



OK

NG

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
5.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
a.

Disconnect the ECM connector.


b.

Disconnect the combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
L26-21 (CHK) - I84-24 (W) Always Below 1 Ω
L26-21 (CHK) or I84-24 (W) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
L26-21 (CHK) - A29-24 (W) Always Below 1 Ω
L26-21 (CHK) or A29-24 (W) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK THAT MIL IS ILLUMINATED
a.

Check if the MIL is illuminated when the ignition switch is turned to ON.

OK:

MIL is illuminated.



Result:
Proceed to
OK
NG



OK

END

NG

7.CHECK THAT ENGINE STARTS
7.CHECK THAT ENGINE STARTS
a.

Turn the ignition switch to ON.


b.

Start the engine.

Result:
Result Proceed to
Engine starts A
Engine does not start* B


HINT:

*: The GTS cannot communicate with the ECM.




A

8.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)

B

8.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
a.

Disconnect the combination meter assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
L26-21 (CHK) - I84-24 (W) Always Below 1 Ω
L26-21 (CHK) or I84-24 (W) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
L26-21 (CHK) - A29-24 (W) Always Below 1 Ω
L26-21 (CHK) or A29-24 (W) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK THAT MIL IS ILLUMINATED
a.

Perform troubleshooting in accordance with the table below.

Result:
MIL Condition Proceed to
Illuminates → Turns off Ignition switch to ON → engine is started A
Other than above - B




A

B

10.CHECK COMMUNICATION BETWEEN GTS AND ECM
10.CHECK COMMUNICATION BETWEEN GTS AND ECM
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine and ECT" item of the Data List.



Result:
Result Proceed to
Communication is possible A
Communication is not possible B



A

11.CHECK WHETHER DTC OUTPUT RECURS

B

11.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: System Select / Health Check.


e.

Check if any DTCs have been detected. Note down any DTCs.

Result:
Result Proceed to
DTCs are not output A
DTCs are output B


HINT:

Check for detected DTCs output from other ECUs which relate to the MIL.




A

12.PERFORM ACTIVE TEST USING GTS (CHECK ENGINE INDICATOR)

B

REPAIR CIRCUITS INDICATED BY OUTPUT DTCS

12.PERFORM ACTIVE TEST USING GTS (CHECK ENGINE INDICATOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Active Test / Check Engine Indicator.

Body Electrical > Combination Meter > Active Test
Tester Display
Check Engine Indicator
50004 122 150

e.

Check the status of the MIL while performing the Active Test.

Result:
Result Proceed to
Changes A
Does not change B




A

B

REPLACE COMBINATION METER ASSEMBLY