Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2017.01
RM25T0E _51 Engine / Hybrid System _029758 1GR-FE ENGINE CONTROL _0135343 SFI SYSTEM J

1GR-FE ENGINE CONTROL  SFI SYSTEM  VC Output Circuit  


DESCRIPTION

The ECM constantly generates 5 V of power from the battery voltages supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power to the sensors through the VC output circuit.

A187745E11
1.708,1.01 2.656,1.208 0.948,0.198 10 false From EFI Fuse 1.271,1.385 2.667,1.583 1.396,0.198 10 false From EFI MAIN Relay 2.854,0.948 3.229,1.146 0.375,0.198 10 false BATT 2.813,1.281 3.406,1.448 0.594,0.167 10 false +B, +B2 0.396,1.875 2.719,2.885 2.323,1.01 10 false Throttle Position Sensor, Accelerator Pedal Position Sensor, etc. (Sensors which have ICs) 0.396,2.875 2.708,3.521 2.313,0.646 10 false Engine Coolant Temperature Sensor, Intake Air Temperature Sensor, etc. 2.76,1.948 3.677,2.302 0.917,0.354 10 false VCTA, VCPA, VCP2, VC 4.073,3.115 4.26,3.313 0.188,0.198 10 false R 4.792,3.396 5.146,3.594 0.354,0.198 10 false ECM 4.417,1.094 6.24,1.292 1.823,0.198 10 false 5 V Constant Voltage Circuit 5.385,1.969 6.375,2.167 0.99,0.198 10 false Microprocessor

When the VC circuit has a short circuit, the CPU in the ECM and sensors that are supplied power through the VC circuit are deactivated because power is not supplied from the VC circuit. When the system is in this condition, it will not start.

WIRING DIAGRAM

·

For the circuit diagram of the ECM power source refer to the ECM power source circuit.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>ECM Power Source Circuit

·

VC Power Source Circuit

A333593E01
5.229,0.719 5.844,0.917 0.615,0.198 10 false VCPA 5.229,1.135 5.688,1.333 0.458,0.198 10 false VPA 5.208,1.396 5.667,1.594 0.458,0.198 10 false EPA 5.208,1.719 5.823,1.917 0.615,0.198 10 false VCP2 5.219,2.083 5.677,2.281 0.458,0.198 10 false VPA2 5.208,2.354 5.667,2.552 0.458,0.198 10 false EPA2 5.229,3.365 5.844,3.563 0.615,0.198 10 false VCTA 5.229,3.771 5.688,3.969 0.458,0.198 10 false VTA1 5.219,4.125 5.833,4.323 0.615,0.198 10 false VTA2 5.208,4.385 5.667,4.583 0.458,0.198 10 false ETA 5.229,7.302 5.844,7.5 0.615,0.198 10 false VV2+ 5.229,7.635 5.844,7.833 0.615,0.198 10 false VV2- 5.24,7.99 5.854,8.188 0.615,0.198 10 false VCV2 4.573,0.844 5.031,1.042 0.458,0.198 10 false I84 4.563,1.167 5.021,1.365 0.458,0.198 10 false I84 4.563,1.49 5.021,1.688 0.458,0.198 10 false I84 4.563,1.802 5.021,2 0.458,0.198 10 false I84 4.563,2.135 5.021,2.333 0.458,0.198 10 false I84 4.552,2.448 5.01,2.646 0.458,0.198 10 false I84 4.906,0.844 5.365,1.042 0.458,0.198 10 false A29 4.906,1.167 5.365,1.365 0.458,0.198 10 false A29 4.896,1.49 5.354,1.688 0.458,0.198 10 false A29 4.896,1.813 5.354,2.01 0.458,0.198 10 false A29 4.896,2.115 5.354,2.313 0.458,0.198 10 false A29 4.896,2.438 5.354,2.635 0.458,0.198 10 false A29 4.906,3.469 5.365,3.667 0.458,0.198 10 false C39 4.906,3.792 5.365,3.99 0.458,0.198 10 false C39 4.885,4.125 5.344,4.323 0.458,0.198 10 false C39 4.885,4.469 5.344,4.667 0.458,0.198 10 false C39 4.885,5.583 5.344,5.781 0.458,0.198 10 false C39 4.906,5.927 5.365,6.125 0.458,0.198 10 false C39 4.885,6.25 5.344,6.448 0.458,0.198 10 false C39 4.552,0.667 6.385,0.865 1.833,0.198 10 false 57*1 57*2 4.552,1 6.385,1.198 1.833,0.198 10 false 55*1 55*2 4.542,1.323 6.375,1.521 1.833,0.198 10 false 59*1 59*2 4.542,1.646 6.375,1.844 1.833,0.198 10 false 58*1 58*2 4.552,1.958 6.385,2.156 1.833,0.198 10 false 56*1 56*2 4.531,2.281 6.365,2.479 1.833,0.198 10 false 60*1 60*2 4.958,3.25 5.271,3.448 0.313,0.198 10 false 96 4.969,3.625 5.281,3.823 0.313,0.198 10 false 98 4.958,3.958 5.271,4.156 0.313,0.198 10 false 99 4.958,4.302 5.271,4.5 0.313,0.198 10 false 97 4.958,7.135 5.271,7.333 0.313,0.198 10 false 67 4.958,7.458 5.271,7.656 0.313,0.198 10 false 90 4.906,7.823 5.365,8.021 0.458,0.198 10 false 113 2.354,0.719 2.51,0.917 0.156,0.198 10 false 4 2.344,1.052 2.5,1.25 0.156,0.198 10 false 6 2.344,1.323 2.5,1.521 0.156,0.198 10 false 5 2.323,1.635 2.479,1.833 0.156,0.198 10 false 1 2.333,1.948 2.49,2.146 0.156,0.198 10 false 3 2.344,2.26 2.5,2.458 0.156,0.198 10 false 2 2.354,3.344 2.51,3.542 0.156,0.198 10 false 5 2.333,3.604 2.49,3.802 0.156,0.198 10 false 4 2.333,3.917 2.49,4.115 0.156,0.198 10 false 6 2.313,4.344 2.469,4.542 0.156,0.198 10 false 3 2.344,5.417 2.5,5.615 0.156,0.198 10 false 3 2.333,5.74 2.49,5.938 0.156,0.198 10 false 1 2.333,6.083 2.49,6.281 0.156,0.198 10 false 2 2.354,7.115 2.51,7.313 0.156,0.198 10 false 1 2.344,7.469 2.5,7.667 0.156,0.198 10 false 2 2.344,7.802 2.5,8 0.156,0.198 10 false 3 1.865,0.833 2.479,1.031 0.615,0.198 10 false VCPA 1.948,1.146 2.406,1.344 0.458,0.198 10 false VPA 1.958,1.458 2.417,1.656 0.458,0.198 10 false EPA 1.896,1.792 2.51,1.99 0.615,0.198 10 false VCP2 1.885,2.115 2.344,2.313 0.458,0.198 10 false VPA2 1.885,2.427 2.5,2.625 0.615,0.198 10 false EPA2 2.063,3.448 2.375,3.646 0.313,0.198 10 false VC 1.99,3.792 2.448,3.99 0.458,0.198 10 false VTA 1.917,4.125 2.531,4.323 0.615,0.198 10 false VTA2 2.073,4.448 2.385,4.646 0.313,0.198 10 false E2 5.24,5.563 5.854,5.76 0.615,0.198 10 false VCV1 5.24,5.906 5.854,6.104 0.615,0.198 10 false VV1+ 5.229,6.25 5.844,6.448 0.615,0.198 10 false VV1- 2.021,5.573 2.333,5.771 0.313,0.198 10 false VC 1.885,5.896 2.5,6.094 0.615,0.198 10 false VVR+ 1.906,6.24 2.521,6.438 0.615,0.198 10 false VVR- 1.896,7.281 2.51,7.479 0.615,0.198 10 false VVL+ 1.917,7.615 2.531,7.813 0.615,0.198 10 false VVL- 2.01,7.969 2.323,8.167 0.313,0.198 10 false VC 4.906,7.302 5.365,7.5 0.458,0.198 10 false C39 4.906,7.646 5.365,7.844 0.458,0.198 10 false C39 4.896,7.99 5.354,8.188 0.458,0.198 10 false C39 1.031,2.698 1.49,2.896 0.458,0.198 10 false I43 1,2.896 6.042,3.094 5.042,0.198 10 false Accelerator Pedal Position Sensor 1.031,4.792 1.344,4.99 0.313,0.198 10 false C4 1.042,4.99 4.708,5.188 3.667,0.198 10 false Throttle Position Sensor 1.021,6.583 1.479,6.781 0.458,0.198 10 false C24 1.031,6.792 4.552,6.99 3.521,0.198 10 false VVT Sensor (for Bank 1) 1.01,8.302 1.469,8.5 0.458,0.198 10 false C22 1.021,8.49 4.542,8.688 3.521,0.198 10 false VVT Sensor (for Bank 2) 3.885,8.24 5.573,8.438 1.688,0.198 10 false *1: for LHD 3.896,8.438 5.427,8.635 1.531,0.198 10 false *2: for RHD 4.917,5.417 5.375,5.615 0.458,0.198 10 false 115 4.948,5.75 5.26,5.948 0.313,0.198 10 false 69 4.948,6.094 5.26,6.292 0.313,0.198 10 false 92 5.635,8.417 6.094,8.615 0.458,0.198 10 false ECM


CAUTION / NOTICE / HINT

NOTICE:

Check the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

When viewed from the rear of the engine assembly, Bank 1 is on the right side and Bank 2 is on the left side.


PROCEDURE

1.CHECK COMMUNICATION BETWEEN GTS AND ECM
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine and ECT" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ECM)

B

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ECM)
a.
A403049C01
0.438,2.448 1.563,3.792 true 0.115,0.104 0.427,0.26 0.313,0.156 10 false *1 0.25,2.375 0.563,2.531 0.313,0.156 10 false *2
*1 Cowl Side Relay Block Assembly
*2 EFI-NO.2 Fuse


Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1 (EFI-NO.2 fuse) - Body ground Ignition switch ON 11 to 14 V


HINT:
·

Check the fuse with it installed to the relay block.

·

If the result is not as specified, since current is not flowing to the +B and +B2 terminals of the ECM, the system may not be started.




Result:
Proceed to
OK
NG



OK

3.CHECK COMMUNICATION BETWEEN GTS AND ECM (CHECK FOR SHORT IN THROTTLE BODY WITH MOTOR ASSEMBLY)

NG

3.CHECK COMMUNICATION BETWEEN GTS AND ECM (CHECK FOR SHORT IN THROTTLE BODY WITH MOTOR ASSEMBLY)
a.

Disconnect the throttle body with motor assembly connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine and ECT" item of the Data List.


Result:
Result Proceed to
Communication is not possible A
Communication is possible B



e.

Reconnect the throttle body with motor assembly connector.



A

4.CHECK COMMUNICATION BETWEEN GTS AND ECM (CHECK FOR SHORT IN ACCELERATOR PEDAL SENSOR ASSEMBLY)

B

REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY

4.CHECK COMMUNICATION BETWEEN GTS AND ECM (CHECK FOR SHORT IN ACCELERATOR PEDAL SENSOR ASSEMBLY)
a.

Disconnect the accelerator pedal sensor assembly connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine and ECT" item of the Data List.


Result:
Result Proceed to
Communication is not possible A
Communication is possible B



e.

Reconnect the accelerator pedal sensor assembly connector.



A

5.CHECK COMMUNICATION BETWEEN GTS AND ECM (CHECK FOR SHORT IN VVT SENSOR FOR BANK 1)

B

REPLACE ACCELERATOR PEDAL(W/SENSOR) ROD ASSEMBLY

5.CHECK COMMUNICATION BETWEEN GTS AND ECM (CHECK FOR SHORT IN VVT SENSOR FOR BANK 1)
a.

Disconnect the VVT sensor (bank 1) connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine and ECT" item of the Data List.


Result:
Result Proceed to
Communication is not possible A
Communication is possible B



e.

Reconnect the VVT sensor (bank 1) connector.



A

6.CHECK COMMUNICATION BETWEEN GTS AND ECM (CHECK FOR SHORT IN VVT SENSOR FOR BANK 2)

B

6.CHECK COMMUNICATION BETWEEN GTS AND ECM (CHECK FOR SHORT IN VVT SENSOR FOR BANK 2)
a.

Disconnect the VVT sensor (bank 2) connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine and ECT" item of the Data List.


Result:
Result Proceed to
Communication is not possible A
Communication is possible B



e.

Reconnect the VVT sensor (bank 2) connector.



A

7.CHECK HARNESS AND CONNECTOR

B

7.CHECK HARNESS AND CONNECTOR
a.

Disconnect the throttle body with motor assembly connector.


b.

Disconnect the accelerator pedal sensor assembly connector.


c.

Disconnect the VVT sensor (bank 1) connector.


d.

Disconnect the VVT sensor (bank 2) connector.


e.

Disconnect the ECM connectors.


f.

Remove the EFI MAIN relay from the engine room relay block assembly.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
I84-57 (VCPA) - Body ground Always 10 kΩ or higher
I84-58 (VCP2) - Body ground Always 10 kΩ or higher
C39-96 (VCTA) - Body ground Always 10 kΩ or higher
C39-115 (VCV1) - Body ground Always 10 kΩ or higher
C39-113 (VCV2) - Body ground Always 10 kΩ or higher
EFI MAIN relay terminal 3 - I84-2 (+B) Always Below 1 Ω
EFI MAIN relay terminal 3 - I84-1 (+B2) Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
A29-57 (VCPA) - Body ground Always 10 kΩ or higher
A29-58 (VCP2) - Body ground Always 10 kΩ or higher
C39-96 (VCTA) - Body ground Always 10 kΩ or higher
C39-115 (VCV1) - Body ground Always 10 kΩ or higher
C39-113 (VCV2) - Body ground Always 10 kΩ or higher
EFI MAIN relay terminal 3 - A29-2 (+B) Always Below 1 Ω
EFI MAIN relay terminal 3 - A29-1 (+B2) Always Below 1 Ω



h.

Reinstall the EFI MAIN relay.


i.

Reconnect the ECM connectors.


j.

Reconnect the throttle body with motor assembly connector.


k.

Reconnect the accelerator pedal sensor assembly connector.


l.

Reconnect the VVT sensor (bank 1) connector.


m.

Reconnect the VVT sensor (bank 2) connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR