Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM › 2017.01–2017.09
RM25T0E _58 Vehicle Interior _029925 THEFT DETERRENT / KEYLESS ENTRY _0138323 IMMOBILISER SYSTEM C

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM  B2799  Engine Immobiliser System Malfunction  


DESCRIPTION

The ECM stores this DTC when a communication line between the ECM and transponder key ECU assembly is malfunctioning or the communication ID of the ECM and transponder key ECU assembly do not match.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2799 Engine Immobiliser System Malfunction One of the following conditions is met:
·

Error in communication between ECM and transponder key ECU assembly.

·

Error in communication lines.

·

Communication ID is different during communication between ECM and transponder key ECU assembly.


·

Harness or connector

·

Transponder key ECU assembly

·

ECM


DTC Output Confirmation Operation:
·

Start the engine and wait 10 seconds.

·

After disconnecting and reconnecting the cable to the negative (-) battery terminal, turn the ignition switch to ON and wait 10 seconds.



Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started -

Related Data List and Active Test
DTC No. Data List and Active Test
B2799 -

WIRING DIAGRAM

B366892E27
1.479,1.406 1.833,1.594 0.354,0.188 10 false IMI 1.417,0.771 1.771,0.958 0.354,0.188 10 false IMO 0.656,2.094 1.125,2.333 0.469,0.24 10 false ECM 0.656,1.927 1.938,2.167 1.281,0.24 10 false I84*1, *4, A29*2, *3 5.5,1.885 5.969,2.125 0.469,0.24 10 false L30 5.521,2.094 6.938,2.583 1.417,0.49 10 false Transponder Key ECU Assembly 1.792,1.302 2.698,1.521 0.906,0.219 10 false 11 1.792,0.656 2.698,0.875 0.906,0.219 10 false 10 2.208,1.698 3.771,1.99 1.563,0.292 10 false *1: for 1GR-FE, LHD 2.229,2.104 5.333,2.417 3.104,0.313 10 false *3: for 1VD-FTV (w/ EGR System) 5.479,1.417 5.979,1.625 0.5,0.208 10 false EFIO 5.479,0.771 5.979,0.979 0.5,0.208 10 false EFII 5.229,0.656 5.51,0.865 0.281,0.208 10 false 12 5.219,1.302 5.5,1.51 0.281,0.208 10 false 13 2.208,1.906 3.771,2.198 1.563,0.292 10 false *2: for 1GR-FE, RHD 2.229,2.313 5.333,2.625 3.104,0.313 10 false *4: for 1VD-FTV (w/o EGR System)

CAUTION / NOTICE / HINT

NOTICE:
·

If the transponder key ECU assembly or ECM is replaced, refer to Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



HINT:

If transponder key ECU assembly DTCs are output simultaneously, troubleshoot the transponder key ECU assembly DTCs first.


PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 61

Result:
Proceed to
NEXT



NEXT

2.CHECK DTC OUTPUT
2.CHECK DTC OUTPUT
a.

Check for DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 61
OK:

DTC B2799 is not output.



Result:
Proceed to
OK
NG



OK

NG

3.REGISTER ECU COMMUNICATION ID
3.REGISTER ECU COMMUNICATION ID
a.

Reregister the ECU communication ID.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

4.CLEAR DTC
4.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 61

Result:
Proceed to
NEXT



NEXT

5.CHECK FOR DTC
5.CHECK FOR DTC
a.

Perform "DTC Output Confirmation Operation" procedure.


b.

Check for DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 61
OK:

B2799 is not output.



Result:
Proceed to
OK
NG



OK

END (ECU COMMUNICATION ID WAS NOT REGISTERED CORRECTLY)

NG

6.CHECK CONNECTION OF CONNECTOR
6.CHECK CONNECTION OF CONNECTOR
a.

Turn the ignition switch off.


b.

Check that the connectors are properly connected to the ECM and transponder key ECU assembly.

OK:

Connectors are properly connected.



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - ECM)

NG

CONNECT CONNECTORS PROPERLY

7.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - ECM)
a.

Disconnect the L30 transponder key ECU assembly connector.


b.

Disconnect the I84*1,*4 or A29*2, *3 ECM connector.

*1: for 1GR-FE, LHD

*2: for 1GR-FE, RHD

*3: for 1VD-FTV (w/ EGR System)

*4: for 1VD-FTV (w/o EGR System)



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1GR-FE, LHD
Tester Connection Condition Specified Condition
L30-12 (EFII) - I84-10 (IMO) Always Below 1 Ω
L30-13 (EFIO) - I84-11 (IMI) Always Below 1 Ω
L30-12 (EFII) - Body ground Always 10 kΩ or higher
L30-13 (EFIO) - Body ground Always 10 kΩ or higher
I84-10 (IMO) - Body ground Always 10 kΩ or higher
I84-11 (IMI) - Body ground Always 10 kΩ or higher

for 1GR-FE, RHD
Tester Connection Condition Specified Condition
L30-12 (EFII) - A29-10 (IMO) Always Below 1 Ω
L30-13 (EFIO) - A29-11 (IMI) Always Below 1 Ω
L30-12 (EFII) - Body ground Always 10 kΩ or higher
L30-13 (EFIO) - Body ground Always 10 kΩ or higher
A29-10 (IMO) - Body ground Always 10 kΩ or higher
A29-11 (IMI) - Body ground Always 10 kΩ or higher

for 1VD-FTV (w/ EGR System)
Tester Connection Condition Specified Condition
L30-12 (EFII) - A29-10 (IMO) Always Below 1 Ω
L30-13 (EFIO) - A29-11 (IMI) Always Below 1 Ω
L30-12 (EFII) - Body ground Always 10 kΩ or higher
L30-13 (EFIO) - Body ground Always 10 kΩ or higher
A29-10 (IMO) - Body ground Always 10 kΩ or higher
A29-11 (IMI) - Body ground Always 10 kΩ or higher

for 1VD-FTV (w/o EGR System)
Tester Connection Condition Specified Condition
L30-12 (EFII) - I84-10 (IMO) Always Below 1 Ω
L30-13 (EFIO) - I84-11 (IMI) Always Below 1 Ω
L30-12 (EFII) - Body ground Always 10 kΩ or higher
L30-13 (EFIO) - Body ground Always 10 kΩ or higher
I84-10 (IMO) - Body ground Always 10 kΩ or higher
I84-11 (IMI) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.REPLACE ECM
a.

Temporarily replace the ECM with a new one.

for 1GR-FE: Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>ECM>REMOVAL

for 1VD-FTV: Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECM>REMOVAL


Result:
Proceed to
NEXT



NEXT

9.REGISTER ECU COMMUNICATION ID
9.REGISTER ECU COMMUNICATION ID
a.

Reregister the ECU communication ID.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

10.CLEAR DTC
10.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 61

Result:
Proceed to
NEXT



NEXT

11.CHECK FOR DTC
11.CHECK FOR DTC
a.

Perform "DTC Output Confirmation Operation" procedure.


b.

Check for DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 61
OK:

B2799 is not output.



Result:
Proceed to
OK
NG



OK

END (ECM WAS DEFECTIVE)

NG

REPLACE TRANSPONDER KEY ECU ASSEMBLY