Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM › 2017.01–2017.09
RM25T0E _58 Vehicle Interior _029925 THEFT DETERRENT / KEYLESS ENTRY _0138323 IMMOBILISER SYSTEM C

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM  B279A  Theft Deterrent System Communication Line High Fixation  


DESCRIPTION

If the communication line (EFIO-IMI) to the transponder key ECU assembly is stuck high (e.g. shorted to +B), the ECM stores this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B279A Theft Deterrent System Communication Line High Fixation Communication line (EFIO-IMI) between the ECM and transponder key ECU assembly is stuck high.
·

Harness or connector

·

ECM

·

Transponder key ECU assembly


DTC Output Confirmation Operation:

Turn the ignition switch to ON and wait 6 seconds.



Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started (initial ignition occurs and engine cranks, then ignition stops) Engine cannot be started

Related Data List and Active Test
DTC No. Data List and Active Test
B279A -

WIRING DIAGRAM

B366893E33
1.802,0.885 2.573,1.073 0.771,0.188 10 false 11 5.208,0.885 5.49,1.073 0.281,0.188 10 false 13 1.469,1.01 1.875,1.24 0.406,0.229 10 false IMI 5.479,1 5.885,1.229 0.406,0.229 10 false EFIO 0.563,1.906 1.958,2.219 1.396,0.313 10 false I84*1, *4, A29*2, *3 0.563,2.073 0.969,2.302 0.406,0.229 10 false ECM 5.219,1.802 5.625,2.031 0.406,0.229 10 false L30 5.208,1.958 6.594,2.344 1.385,0.385 10 false Transponder Key ECU Assembly 2.198,1.604 3.958,1.906 1.76,0.302 10 false *1: for 1GR-FE, LHD 2.219,2 5.156,2.333 2.938,0.333 10 false *3: for 1VD-FTV (w/ EGR System) 2.208,1.802 3.969,2.104 1.76,0.302 10 false *2: for 1GR-FE, RHD 2.219,2.177 5.156,2.51 2.938,0.333 10 false *4: for 1VD-FTV (w/o EGR System)

CAUTION / NOTICE / HINT

NOTICE:
·

If the transponder key ECU assembly or ECM is replaced, refer to Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 61

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Perform "DTC Output Confirmation Operation" procedure.


b.

Check for DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 61
OK:

DTC B279A is not output.



Result:
Result Proceed to
B279A is not output A
B279A is output B



A

B

3.CHECK CONNECTION OF CONNECTOR
3.CHECK CONNECTION OF CONNECTOR
a.

Check that the connectors are properly connected to the ECM and transponder key ECU assembly.

OK:

Connectors are properly connected.



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - ECM)

NG

CONNECT CONNECTORS PROPERLY

4.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - ECM)
a.

Disconnect the L30 transponder key ECU assembly connector.


b.

Disconnect the I84*1,*4 or A29*2, *3 ECM connector.

*1: for 1GR-FE, LHD

*2: for 1GR-FE, RHD

*3: for 1VD-FTV (w/ EGR System)

*4: for 1VD-FTV (w/o EGR System)



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1GR-FE, LHD
Tester Connection Condition Specified Condition
L30-13 (EFIO) - I84-11 (IMI) Always Below 1 Ω
I84-11 (IMI) or L30-13 (EFIO) - Body ground Always 10 kΩ or higher

for 1GR-FE, RHD
Tester Connection Condition Specified Condition
L30-13 (EFIO) - A29-11 (IMI) Always Below 1 Ω
A29-11 (IMI) or L30-13 (EFIO) - Body ground Always 10 kΩ or higher

for 1VD-FTV (w/ EGR System)
Tester Connection Condition Specified Condition
L30-13 (EFIO) - A29-11 (IMI) Always Below 1 Ω
A29-11 (IMI) or L30-13 (EFIO) - Body ground Always 10 kΩ or higher

for 1VD-FTV (w/o EGR System)
Tester Connection Condition Specified Condition
L30-13 (EFIO) - I84-11 (IMI) Always Below 1 Ω
I84-11 (IMI) or L30-13 (EFIO) - Body ground Always 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L30-13 (EFIO) - Body ground Always Below 1 V



Result:
Proceed to
OK
NG



OK

5.REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE TRANSPONDER KEY ECU ASSEMBLY
a.

Replace the transponder key ECU assembly with a new one.

HINT:

Refer to Service Bulletin.


NOTICE:

Key ID code registration is necessary when replacing the transponder key ECU assembly, refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

6.CLEAR DTC
6.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 61

Result:
Proceed to
NEXT



NEXT

7.CHECK FOR DTC
7.CHECK FOR DTC
a.

Perform "DTC Output Confirmation Operation" procedure.


b.

Check for DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 61
OK:

DTC B279A is not output.



Result:
Result Proceed to
B279A is not output A
B279A is output B



A

END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE)

B