Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM › from 2017.09
RM25T0E _58 Vehicle Interior _029925 THEFT DETERRENT / KEYLESS ENTRY _0138323 IMMOBILISER SYSTEM C

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM  B279A  Theft Deterrent System Communication Line High Fixation  


DESCRIPTION

When the communication line (EFIO-IMI) between the transponder key ECU assembly and ECM is stuck on HI output, the ECM stores this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B279A Theft Deterrent System Communication Line High Fixation The communication line (EFIO-IMI) between the ECM and transponder key ECU assembly is stuck on HI output (1 trip detection logic*).
·

Harness or connector

·

ECM

·

Transponder key ECU assembly


DTC Output Confirmation Operation:

Turn the ignition switch to ON and wait 6 seconds.



*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started (initial ignition occurs and engine cranks, then ignition stops) Engine cannot be started

Related Data List and Active Test
DTC No. Data List and Active Test
B279A -

WIRING DIAGRAM

B416734E18
1.771,0.521 2.083,0.75 0.313,0.229 10 false +B 2.052,0.865 2.365,1.094 0.313,0.229 10 false IMI 2.313,0.865 2.625,1.094 0.313,0.229 10 false 11 0.719,1.896 1.875,2.125 1.156,0.229 10 false A29*1, I84*2 0.729,2.073 1.26,2.292 0.531,0.219 10 false ECM 4.771,0.854 5.083,1.083 0.313,0.229 10 false 13 5.031,0.854 5.771,1.083 0.74,0.229 10 false EFIO 4.979,1.885 5.719,2.115 0.74,0.229 10 false L30 4.979,2.052 7.031,2.25 2.052,0.198 10 false Transponder Key ECU Assembly 2.542,2.073 3.875,2.365 1.333,0.292 10 false *1: for RHD 2.542,2.438 3.875,2.729 1.333,0.292 10 false *2: for LHD

CAUTION / NOTICE / HINT

NOTICE:
·

If the transponder key ECU assembly or ECM is replaced, refer to Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



PROCEDURE

1.CHECK CONNECTION OF CONNECTOR
a.

Check that the connectors are properly connected to the ECM and transponder key ECU assembly.

OK:

Connectors are properly connected.



Result:
Proceed to
OK
NG



OK

2.CHECK ECM (IMI TERMINAL VOLTAGE)

NG

CONNECT CONNECTORS PROPERLY

2.CHECK ECM (IMI TERMINAL VOLTAGE)
a.

Disconnect the transponder key ECU assembly connector.


b.
B488849C02
1.552,0.26 2.01,0.51 0.458,0.25 2.698,0.594 2.51,0.594 2.51,0.594 2.052,1.427 true 1.667,0.313 2.125,0.51 0.458,0.198 10 false L30 2.771,0.542 3.229,0.74 0.458,0.198 10 false EFIO 0.094,0.115 0.552,0.313 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Transponder Key ECU Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L30-13 (EFIO) - Body ground Always 11 to 14 V



c.

Connect the transponder key ECU assembly connector.


Result:
Proceed to
OK
NG



OK

3.CHECK TRANSPONDER KEY ECU ASSEMBLY (TERMINAL EFIO)

NG

4.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - ECM AND BODY GROUND)
3.CHECK TRANSPONDER KEY ECU ASSEMBLY (TERMINAL EFIO)
a.

Using an oscilloscope, check the waveform.

B489444C01
3.292,0.5 3.74,0.729 0.448,0.229 2.313,2.125 2.51,2.125 2.51,2.125 3.219,1.313 true 2.094,0.729 2.406,0.927 0.313,0.198 10 false *a 3.396,0.521 3.708,0.719 0.313,0.198 10 false L30 3.677,3.01 4.01,3.292 0.333,0.281 10 false *b 1.292,3.896 1.656,4.125 0.365,0.229 10 false GND 1.927,2.063 2.292,2.292 0.365,0.229 10 false EFIO
*a Component with harness connected
(Transponder Key ECU Assembly)
*b Waveform


Measurement Condition:
Item Content
Tester Connection L30-13 (EFIO) - Body ground
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal


OK:

Waveform is similar to that shown in the illustration.



Result:
Proceed to
OK (for 1GR-FE)
OK (for 1VD-FTV)
NG



OK (for 1GR-FE)

OK (for 1VD-FTV)

NG

REPLACE TRANSPONDER KEY ECU ASSEMBLY (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE)

4.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - ECM AND BODY GROUND)
a.

Disconnect the A29*1, I84*2 ECM connector.

*1: for RHD

*2: for LHD



b.

Disconnect the L30 transponder key ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RHD
Tester Connection Condition Specified Condition
L30-13 (EFIO) - A29-11 (IMI) Always Below 1 Ω
A29-11 (IMI) - Body ground Always 10 kΩ or higher
L30-13 (EFIO) - Body ground Always 10 kΩ or higher

for LHD
Tester Connection Condition Specified Condition
L30-13 (EFIO) - I84-11 (IMI) Always Below 1 Ω
I84-11 (IMI) - Body ground Always 10 kΩ or higher
L30-13 (EFIO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK (for 1GR-FE)
OK (for 1VD-FTV)
NG



OK (for 1GR-FE)

OK (for 1VD-FTV)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR