Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM › from 2017.09
RM25T0E _51 Engine / Hybrid System _029760 1VD-FTV ENGINE CONTROL _0135360 ECD SYSTEM C

1VD-FTV ENGINE CONTROL  ECD SYSTEM  P2120  Throttle / Pedal Position Sensor / Switch "D" Circuit  P2122  Throttle / Pedal Position Sensor / Switch "D" Circuit Low Input  P2123  Throttle / Pedal Position Sensor / Switch "D" Circuit High Input  P2125  Throttle / Pedal Position Sensor / Switch "E" Circuit  P2127  Throttle / Pedal Position Sensor / Switch "E" Circuit Low Input  P2128  Throttle / Pedal Position Sensor / Switch "E" Circuit High Input  P2138  Throttle / Pedal Position Sensor / Switch "D" / "E" Voltage Correlation  


DESCRIPTION

HINT:
·

This is the repair procedure for the accelerator pedal position sensor.

·

This electrical throttle system does not use a throttle cable.

·

This accelerator pedal position sensor is a non-contact type.



The accelerator pedal position sensor is mounted on the accelerator pedal and detects the opening angle of the accelerator pedal. Since this sensor is electronically controlled with Hall-effect elements, accurate control and reliability can be obtained. It has 2 sensors to detect the accelerator position and a malfunction of the accelerator position sensor.

In the accelerator pedal position sensor, the voltage applied to terminals VPA and VPA2 of the ECM changes between 0 V and 5 V in proportion to the opening angle of the accelerator pedal. The VPA is a signal to indicate the actual accelerator pedal opening angle which is used for the engine control, and the VPA2 is a signal to indicate the information about the opening angle which is used for detecting malfunctions.

The ECM judges the current opening angle of the accelerator pedal using signals from terminals VPA and VPA2, and the ECM controls the injection volume based on these signals.

A129363E11
0.792,2.677 0.271,1.469 0.271,1.469 0.323,1.469 true 0.792,3.063 0.271,4.271 0.271,4.271 0.333,4.271 true 0.917,2.208 1.281,1.469 true 1.281,4.25 0.917,3.51 true 5.667,1.313 5.979,1.49 true 6.052,1.771 6.375,1.948 false 2.406,0.198 4.094,0.552 1.688,0.354 10 false Accelerator Pedal Position Sensor Output Voltage (V) 0.219,0.74 1.469,1.135 1.25,0.396 10 false Accelerator Pedal Position Sensor 1.323,1.396 1.927,1.604 0.604,0.208 10 false Magnet 0.375,1.396 1.042,1.604 0.667,0.208 10 false IC No. 1 0.375,4.188 1.021,4.385 0.646,0.198 10 false IC No. 2 1.323,4.188 1.833,4.396 0.51,0.208 10 false Magnet 1.521,1.781 1.865,1.979 0.344,0.198 10 false VPA 1.521,2.135 1.885,2.333 0.365,0.198 10 false EPA 1.469,2.51 1.938,2.708 0.469,0.198 10 false VCPA 1.469,2.875 1.906,3.073 0.438,0.198 10 false VPA2 1.469,3.25 1.917,3.448 0.448,0.198 10 false EPA2 1.469,3.615 1.927,3.813 0.458,0.198 10 false VCP2 2.177,1.51 2.583,1.708 0.406,0.198 10 false ECM 3.927,1.125 4.063,1.323 0.135,0.198 10 false 5 3.427,1.531 4.083,1.729 0.656,0.198 10 false 3.7 to 5.0 3.427,1.833 4.083,2.042 0.656,0.208 10 false 2.9 to 4.2 3.427,2.458 4.083,2.656 0.656,0.198 10 false 1.4 to 1.8 3.427,2.802 4.073,3 0.646,0.198 10 false 0.6 to 1.0 4.021,3.542 4.135,3.74 0.115,0.198 10 false 0 4.448,3.448 5.542,3.646 1.094,0.198 10 false Usable Range 5.667,3.531 5.979,3.729 0.313,0.198 10 false 20.6 6.417,1.906 6.781,2.104 0.365,0.198 10 false VPA 5.26,1.229 5.719,1.427 0.458,0.198 10 false VPA2 4.365,3.75 6.906,3.958 2.542,0.208 10 false Accelerator Pedal Turning Angle (°) 0.26,4.875 2.625,5.073 2.365,0.198 10 false *1: Accelerator Pedal Fully Released 0.26,5.302 2.729,5.51 2.469,0.208 10 false *2: Accelerator Pedal Fully Depressed 4.427,0.573 4.615,0.771 0.188,0.198 10 false *1 5.76,0.573 5.948,0.771 0.188,0.198 10 false *2

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2120 Throttle / Pedal Position Sensor / Switch "D" Circuit Condition (a) continues for 0.5 seconds or more:
(1 trip detection logic)
(a) VPA less than 0.4 V and VPA2 greater than 0.97 deg, or VPA greater than 4.8 V
·

Accelerator pedal position sensor

·

Accelerator pedal

·

Accelerator pedal rod (arm) deformed

·

ECM


Comes on DTC stored
P2122 Throttle / Pedal Position Sensor / Switch "D" Circuit Low Input Condition (a) and (b) continue for 0.5 seconds or more:
(1 trip detection logic)
(a) VPA less than 0.4 V
(b) VPA2 greater than 0.97 deg
·

Accelerator pedal position sensor

·

Open in VCPA circuit

·

VPA circuit open or ground short

·

Accelerator pedal

·

Accelerator pedal rod (arm) deformed

·

ECM


Comes on DTC stored
P2123 Throttle / Pedal Position Sensor / Switch "D" Circuit High Input Condition (a) continues for 2.0 seconds or more:
(1 trip detection logic)
(a) VPA greater than 4.8 V
·

Accelerator pedal position sensor

·

Open in EPA circuit

·

Accelerator pedal

·

Accelerator pedal rod (arm) deformed

·

ECM


Comes on DTC stored
P2125 Throttle / Pedal Position Sensor / Switch "E" Circuit Condition (a) continues for 0.5 seconds or more:
(1 trip detection logic)
(a) VPA2 less than 1.2 V and VPA greater than 2.7 deg, or VPA2 greater than 4.8 V and VPA greater than 0.4 V but less than 3.45 V
·

Accelerator pedal position sensor

·

Accelerator pedal

·

Accelerator pedal rod (arm) deformed

·

ECM


Comes on DTC stored
P2127 Throttle / Pedal Position Sensor / Switch "E" Circuit Low Input Condition (a) and (b) continue for 1.2 seconds or more:
(1 trip detection logic)
(a) VPA2 less than 1.2 V
(b) VPA1 greater than 2.7 deg
·

Accelerator pedal position sensor

·

Open in VCP2 circuit

·

VPA2 circuit open or ground short

·

Accelerator pedal

·

Accelerator pedal rod (arm) deformed

·

ECM


Comes on DTC stored
P2128 Throttle / Pedal Position Sensor / Switch "E" Circuit High Input Condition (a) and (b) continue for 2.0 seconds or more:
(1 trip detection logic)
(a) VPA2 greater than 4.8 V
(b) VPA greater than 0.4 V but less than 3.45 V
·

Accelerator pedal position sensor

·

Open in EPA2 circuit

·

Accelerator pedal

·

Accelerator pedal rod (arm) deformed

·

ECM


Comes on DTC stored
P2138 Throttle / Pedal Position Sensor / Switch "D" / "E" Voltage Correlation Condition (a) or (b) continues for 2.0 seconds or more:
(1 trip detection logic)
(a) Difference between VPA and VPA2 less than 0.02 V
(b) VPA less than 0.4 V and VPA2 less than 1.2 V
·

VPA and VPA2 circuits are short circuited

·

Accelerator pedal position sensor

·

Accelerator pedal

·

Accelerator pedal rod (arm) deformed

·

ECM


Comes on DTC stored

HINT:

When DTC P2120, P2122, P2123, P2125, P2127, P2128 or P2138 is detected, check the output voltage of the accelerator pedal position sensor by entering the following menus on the GTS: Powertrain / Engine and ECT / Data List / Accel Position 1 and Accel Position 2.

Trouble Area Accelerator pedal position expressed as voltage output
Accelerator pedal released Accelerator pedal depressed
Accel Position 1 Accel Position 2 Accel Position 1 Accel Position 2
VC circuit open 0 to 0.2 V 0 to 0.2 V 0 to 0.2 V 0 to 0.2 V
VPA circuit open or ground short 0 to 0.2 V 1.2 to 2.0 V 0 to 0.2 V 3.4 to 5.0 V
VPA2 circuit open or ground short 0.5 to 1.1 V 0 to 0.2 V 2.9 to 3.6 V 0 to 0.2 V
EPA circuit open 4.5 to 5.0 V 4.5 to 5.0 V 4.5 to 5.0 V 4.5 to 5.0 V


CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P2120
P2122
P2123
P2125
P2127
P2128
P2138
Ignition switch ON
·

Accelerator pedal fully released for 3 seconds

·

Accelerator pedal depressed partway for 3 seconds

·

Accelerator pedal fully depressed for 3 seconds



WIRING DIAGRAM

A149601E61
0.281,3.167 2.438,3.375 2.156,0.208 10 false Accelerator Pedal Position Sensor 5.594,1.271 6.052,1.479 0.458,0.208 10 false VCPA 5.333,1.281 5.51,1.49 0.177,0.208 10 false 55 5.333,0.438 5.51,0.646 0.177,0.208 10 false 53 5.333,0.865 5.51,1.073 0.177,0.208 10 false 57 5.333,2.531 5.51,2.74 0.177,0.208 10 false 56 5.333,1.688 5.51,1.896 0.177,0.208 10 false 54 5.333,2.115 5.51,2.323 0.177,0.208 10 false 58 5.604,0.448 6,0.656 0.396,0.208 10 false VPA 5.604,0.854 6.052,1.063 0.448,0.208 10 false EPA 5.604,2.542 6.052,2.75 0.448,0.208 10 false VCP2 5.604,1.698 6.042,1.906 0.438,0.208 10 false VPA2 5.604,2.115 6.198,2.323 0.594,0.208 10 false EPA2 1.5,1.313 1.958,1.521 0.458,0.208 10 false VCPA 1.573,0.469 1.885,0.677 0.313,0.208 10 false VPA 1.573,0.896 1.917,1.104 0.344,0.208 10 false EPA 1.5,2.583 1.948,2.792 0.448,0.208 10 false VCP2 1.5,1.74 1.938,1.948 0.438,0.208 10 false VPA2 1.5,2.156 1.927,2.365 0.427,0.208 10 false EPA2 1.99,1.271 2.198,1.479 0.208,0.208 10 false 4 1.99,0.438 2.198,0.646 0.208,0.208 10 false 6 1.99,0.844 2.198,1.052 0.208,0.208 10 false 5 1.99,2.531 2.198,2.74 0.208,0.208 10 false 1 1.99,1.688 2.198,1.896 0.208,0.208 10 false 3 1.99,2.104 2.198,2.313 0.208,0.208 10 false 2 5.979,3.229 6.375,3.427 0.396,0.198 10 false ECM 5.719,3.063 6.219,3.271 0.5,0.208 10 false A29*1 0.281,3.01 0.563,3.198 0.281,0.188 10 false I43 6.24,3.063 6.74,3.271 0.5,0.208 10 false I84*2 4.219,3.323 5.24,3.521 1.021,0.198 10 false *2: for LHD 4.219,3.01 5.24,3.208 1.021,0.198 10 false *1: for RHD

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (ACCELERATOR PEDAL POSITION)
a.

Connect the GTS to the DLC3.


b.
C129061C23
0.698,1.635 1.448,1.844 0.75,0.208 10 false *a 0.292,0.115 1.625,0.323 1.333,0.208 10 false *1 2.26,1.615 2.927,1.823 0.667,0.208 10 false *b
*1 Accelerator Pedal
*a Depressed
*b Released


Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Accel Sens. No.1 Volt % and Accel Sens. No.2 Volt %.

Powertrain > Engine and ECT > Data List
Tester Display
Accel Sens. No.1 Volt %
Accel Sens. No.2 Volt %
50003 61 75,76

d.

Read the values.

Standard voltage:
Accelerator Pedal Accel Sens. No. 1 Volt % Accel Sens. No. 2 Volt %
Released 10 to 22% 24 to 40%
Depressed 52 to 90% 68 to 99%



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM)
2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM)
a.
A311474C06
2.125,2.479 2.573,2.75 0.448,0.271 1.49,0.219 1.938,0.49 0.448,0.271 1.344,2.469 1.792,2.74 0.448,0.271 0.688,1.281 1.354,1.125 true 1.365,1.688 1.667,1.146 true 0.896,1.51 1.542,1.146 true 1.844,1.688 1.792,1.135 true 1.917,1.156 2.219,1.531 true 2.063,1.135 2.563,1.406 true 1.823,3.781 0.646,3.615 true 1.917,3.781 0.802,4.125 true 2.01,3.781 1.125,4.302 true 2.083,3.781 1.583,4.375 true 2.26,3.781 2.625,4.094 true 2.188,3.781 2.125,4.208 true 0.177,0.167 0.49,0.365 0.313,0.198 10 false *a 0.177,2.448 0.49,2.646 0.313,0.198 10 false *b 2.25,2.531 2.573,2.719 0.323,0.188 10 false I84 1.615,0.281 1.865,0.448 0.25,0.167 10 false I43 0.271,1.219 0.885,1.417 0.615,0.198 10 false VCP2 0.615,1.521 1.229,1.719 0.615,0.198 10 false EPA2 1.208,1.719 1.823,1.917 0.615,0.198 10 false VPA2 1.781,1.729 2.396,1.927 0.615,0.198 10 false VCPA 2.24,1.563 2.854,1.76 0.615,0.198 10 false EPA 2.625,1.406 3.24,1.604 0.615,0.198 10 false VPA 0.104,4.073 1.031,4.344 0.927,0.271 10 false 54 (VPA2) 0.063,3.51 0.74,3.802 0.677,0.292 10 false 53 (VPA) 0.698,4.323 1.792,4.583 1.094,0.26 10 false 55 (VCPA) 1.448,4.406 2.823,4.604 1.375,0.198 10 false 56 (VCP2) 1.938,4.24 3.313,4.438 1.375,0.198 10 false 57 (EPA) 2.5,4.115 3.323,4.344 0.823,0.229 10 false 58 (EPA2) 1.448,2.531 1.771,2.719 0.323,0.188 10 false A29 1.583,2.271 1.906,2.458 0.323,0.188 10 false *A 2.427,2.281 2.75,2.469 0.323,0.188 10 false *B
*A for RHD
*B for LHD
*a Front view of wire harness connector
(to Accelerator Pedal Position Sensor)
*b Front view of wire harness connector
(to ECM)


Disconnect the accelerator pedal position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
for RHD
Tester Connection Condition Specified Condition
I43-1 (VCP2) - A29-56 (VCP2) Always Below 1 Ω
I43-2 (EPA2) - A29-58 (EPA2) Always Below 1 Ω
I43-3 (VPA2) - A29-54 (VPA2) Always Below 1 Ω
I43-4 (VCPA) - A29-55 (VCPA) Always Below 1 Ω
I43-5 (EPA) - A29-57 (EPA) Always Below 1 Ω
I43-6 (VPA) - A29-53 (VPA) Always Below 1 Ω
I43-1 (VCP2) or A29-56 (VCP2) - Body ground Always 10 kΩ or higher
I43-2 (EPA2) or A29-58 (EPA2) - Body ground Always 10 kΩ or higher
I43-3 (VPA2) or A29-54 (VPA2) - Body ground Always 10 kΩ or higher
I43-4 (VCPA) or A29-55 (VCPA) - Body ground Always 10 kΩ or higher
I43-5 (EPA) or A29-57 (EPA) - Body ground Always 10 kΩ or higher
I43-6 (VPA) or A29-53 (VPA) - Body ground Always 10 kΩ or higher

for LHD
Tester Connection Condition Specified Condition
I43-1 (VCP2) - I84-56 (VCP2) Always Below 1 Ω
I43-2 (EPA2) - I84-58 (EPA2) Always Below 1 Ω
I43-3 (VPA2) - I84-54 (VPA2) Always Below 1 Ω
I43-4 (VCPA) - I84-55 (VCPA) Always Below 1 Ω
I43-5 (EPA) - I84-57 (EPA) Always Below 1 Ω
I43-6 (VPA) - I84-53 (VPA) Always Below 1 Ω
I43-1 (VCP2) or I84-56 (VCP2) - Body ground Always 10 kΩ or higher
I43-2 (EPA2) or I84-58 (EPA2) - Body ground Always 10 kΩ or higher
I43-3 (VPA2) or I84-54 (VPA2) - Body ground Always 10 kΩ or higher
I43-4 (VCPA) or I84-55 (VCPA) - Body ground Always 10 kΩ or higher
I43-5 (EPA) or I84-57 (EPA) - Body ground Always 10 kΩ or higher
I43-6 (VPA) or I84-53 (VPA) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT ECM TERMINAL VOLTAGE (VCPA AND VCP2 TERMINALS)

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.INSPECT ECM TERMINAL VOLTAGE (VCPA AND VCP2 TERMINALS)
a.
A115666C08
0.292,1.604 0.844,1.938 0.552,0.333 0.719,2.479 1.313,1.833 false 1.354,2.479 1.469,1.854 false 1.99,2.479 1.74,1.854 false 2.51,2.469 1.896,1.854 false 0.25,0.385 2.688,0.74 2.438,0.354 10 false *a 1.781,2.521 2.177,2.688 0.396,0.167 10 false VCPA 0.479,2.521 0.875,2.688 0.396,0.167 10 false VCP2 2.427,2.521 2.75,2.688 0.323,0.167 10 false EPA 1.135,2.521 1.542,2.688 0.406,0.167 10 false EPA2 0.458,1.688 0.698,1.865 0.24,0.177 10 false I43
*a Front view of wire harness connector
(to Accelerator Pedal Position Sensor)


Disconnect the accelerator pedal position sensor.


b.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
I43-4 (VCPA) - I43-5 (EPA) Ignition switch ON 4.5 to 5.5 V
I43-1 (VCP2) - I43-2 (EPA2) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

4.REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY

NG

7.REPLACE ECM
4.REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY
a.

Replace the accelerator pedal sensor assembly.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ACCELERATOR PEDAL>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CHECK IF OUTPUT DTC RECURS
5.CHECK IF OUTPUT DTC RECURS
a.

Connect the GTS to the DLC3.


b.

Clear the DTC.

Powertrain > Engine and ECT > Clear DTCs
50002 61

c.

Turn the ignition switch off and leave the vehicle for 30 seconds.


d.

Turn the ignition switch ON.


e.

Fully release the accelerator pedal for 3 seconds or more, then depress it partway for 3 seconds or more, and then fully depress it for 3 seconds or more.


f.

Confirm that the DTC is not output again.

Result:
Proceed to
NEXT




NEXT

END

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

5.CHECK IF OUTPUT DTC RECURS
7.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

5.CHECK IF OUTPUT DTC RECURS