Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM › from 2017.09
RM25T0E _51 Engine / Hybrid System _029760 1VD-FTV ENGINE CONTROL _0135360 ECD SYSTEM J

1VD-FTV ENGINE CONTROL  ECD SYSTEM  MIL Circuit  


DESCRIPTION

for RHD

The MIL (Malfunction Indicator Lamp) is used to indicate vehicle malfunction detections by the ECM. When the ignition switch is turned to ON, power is supplied to the MIL circuit, and the ECM provides the circuit ground which illuminates the MIL.

The Malfunction Indicator Lamp (MIL) is used to indicate vehicle malfunctions detected by the ECM.The MIL operation can be checked visually. When the ignition switch is first turned to ON, the MIL shouldbe illuminated and should then turn off after the engine is started. If the MIL remains illuminated or is notilluminated, conduct the following troubleshooting procedure using the GTS.


for LHD

The Malfunction Indicator Lamp (MIL) is used to indicate vehicle malfunctions detected by the ECM.The MIL operation can be checked visually. When the ignition switch is first turned to ON, the MIL shouldbe illuminated and should then turn off after the engine is started. If the MIL remains illuminated or is notilluminated, conduct the following troubleshooting procedure using the GTS.


WIRING DIAGRAM

for RHD
A182518E16
6.198,2.427 6.563,2.583 0.365,0.156 10 false A29 6.198,2.583 6.594,2.74 0.396,0.156 10 false ECM 6.031,1.01 6.25,1.167 0.219,0.156 10 false W 5.76,1.01 5.958,1.167 0.198,0.156 10 false 24 4.896,1.125 5.219,1.281 0.323,0.156 10 false L25 4.948,0.927 5.146,1.083 0.198,0.156 10 false 12 2.708,1.125 3.031,1.281 0.323,0.156 10 false L25 2.771,0.906 2.969,1.063 0.198,0.156 10 false 28 3.708,1.281 4,1.448 0.292,0.167 10 false MIL 4.51,1.229 4.844,1.396 0.333,0.167 10 false CHK 3.063,1.229 3.271,1.396 0.208,0.167 10 false B 1.99,1.25 2.344,1.417 0.354,0.167 10 false MET 3.375,2.083 4.625,2.25 1.25,0.167 10 false Combination Meter 0.188,1.104 1.438,1.302 1.25,0.198 10 false from Ignition Switch

for LHD
A403501E01
0.771,2.292 2.688,2.49 1.917,0.198 10 false Combination Meter Assembly 0.771,2.115 1.073,2.292 0.302,0.177 10 false L26 0.958,3.417 2.875,3.615 1.917,0.198 10 false : CAN Communication Line 2.01,0.885 2.458,1.083 0.448,0.198 10 false CANH 4.771,0.885 5.219,1.083 0.448,0.198 10 false CANH 4.76,1.583 5.208,1.781 0.448,0.198 10 false CANL 2.042,1.594 2.49,1.792 0.448,0.198 10 false CANL 2.5,1.417 2.948,1.615 0.448,0.198 10 false 14 2.521,0.708 2.969,0.906 0.448,0.198 10 false 13 4.49,0.729 4.938,0.917 0.448,0.188 10 false 41 4.51,1.396 4.958,1.583 0.448,0.188 10 false 49 5.031,2.146 5.479,2.333 0.448,0.188 10 false I84 5.323,2.146 5.771,2.333 0.448,0.188 10 false ECM

PROCEDURE

1.CHECK THAT MIL IS ILLUMINATED
a.

Check the illumination condition of the MIL.


Result:
MIL Condition Proceed to
Illuminates → Turns off Ignition switch to ON → Engine is started A
Other than above - B (for LHD)
Other than above - B (for RHD)



A

B (for LHD)

2.CHECK CONNECTION BETWEEN GTS AND ECM

B (for RHD)

5.CHECK THAT MIL IS ILLUMINATED
2.CHECK CONNECTION BETWEEN GTS AND ECM
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is possible A
Communication is not possible B



A

3.CHECK WHETHER DTC OUTPUT RECURS

B

3.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 61

e.

Check if any DTCs have been detected. Note down any DTCs.


Result:
Result Proceed to
DTCs are not output A
Any DTCs is output B


HINT:

Check for detected DTCs output from other ECUs which relate to the MIL.



A

4.PERFORM ACTIVE TEST USING GTS

B

REPAIR CIRCUIT INDICATED BY OUTPUT DTC

4.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Active Test / Check Engine Indicator.

Body Electrical > Combination Meter > Active Test
Tester Display
Check Engine Indicator
50004 122 150

e.

Check the status of the MIL while performing the Active Test.

Result:
Result Proceed to
Changes A
Does not change B




A

B

REPLACE COMBINATION METER ASSEMBLY

5.CHECK THAT MIL IS ILLUMINATED
a.

Perform troubleshooting in accordance with the table below.

Result:
Result Proceed to
MIL remains ON A
MIL does not illuminate B




A

6.CHECK WHETHER MIL TURNS OFF

B

9.CHECK THAT MIL IS ILLUMINATED
6.CHECK WHETHER MIL TURNS OFF
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch ON and turn the GTS on.


c.

Check if DTCs have been stored .If DTCs are present, write them down.



e.

Check that the MIL turns OFF.

Standard:

MIL turns OFF.



Result:
Proceed to
OK
NG



OK

REPAIR CIRCUITS INDICATED BY OUTPUT DTCS

NG

7.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
7.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
a.
A166420C02
1.448,0.792 1.875,1.083 0.427,0.292 0.229,0.125 0.406,0.323 0.177,0.198 10 false *a 1.531,0.865 1.844,1.021 0.313,0.156 10 false A29
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Turn the ignition switch ON.


c.

Check that the MIL is not illuminated.

OK:

MIL is not illuminated.



Result:
Proceed to
OK
NG



OK

NG

8.CHECK HARNESS AND CONNECTOR (COMBINATION METER - ECM)
8.CHECK HARNESS AND CONNECTOR (COMBINATION METER - ECM)
a.

Disconnect the combination meter connector.


b.

Disconnect the ECM connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
L25-12 (CHK) - A29-24 (W) Always Below 1 Ω
L25-12 (CHK) or A29-24 (W) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK THAT MIL IS ILLUMINATED
a.

Check if the MIL is illuminated when the ignition switch is turned ON.

OK:

MIL should be illuminated.



Result:
Proceed to
OK
NG



OK

END

NG

10.CHECK THAT ENGINE STARTS
10.CHECK THAT ENGINE STARTS
a.

Turn the ignition switch ON.


b.

Start the engine.

Result:
Result Proceed to
Engine starts A
Engine does not start* B


HINT:

*: The GTS cannot communicate with the ECM.




A

11.CHECK COMBINATION METER ASSEMBLY (MIL CIRCUIT)

B

11.CHECK COMBINATION METER ASSEMBLY (MIL CIRCUIT)
a.

See the combination meter troubleshooting procedure.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (COMBINATION METER - ECM)

NG

REPLACE COMBINATION METER ASSEMBLY