Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM › from 2017.09
RM25T0E _51 Engine / Hybrid System _029760 1VD-FTV ENGINE CONTROL _0135360 ECD SYSTEM C

1VD-FTV ENGINE CONTROL  ECD SYSTEM  P0405  Exhaust Gas Recirculation Sensor "A" Circuit Low  P0406  Exhaust Gas Recirculation Sensor "A" Circuit High  P0407  Exhaust Gas Recirculation Sensor "B" Circuit Low  P0408  Exhaust Gas Recirculation Sensor "B" Circuit High  


DESCRIPTION

The EGR valve position sensor is mounted on the EGR valve and used for detecting the lift amount of the valve. The lift amount detected by the sensor is provided to the ECM as feedback. The ECM then regulates the lift amount of the valve in accordance with engine running conditions.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0405 Exhaust Gas Recirculation Sensor "A" Circuit Low No. 1 EGR valve position sensor output voltage is less than 0.1 V for more than 5 seconds
(1 trip detection logic)
·

Open or short in No. 1 EGR valve position sensor circuit

·

No. 1 EGR valve (EGR valve position sensor)

·

ECM


Comes on DTC stored
P0406 Exhaust Gas Recirculation Sensor "A" Circuit High No. 1 EGR valve position sensor output voltage is more than 4.9 V for more than 5 seconds
(1 trip detection logic)
·

Open or short in No. 1 EGR valve position sensor circuit

·

No. 1 EGR valve (EGR valve position sensor)

·

ECM


Comes on DTC stored
P0407 Exhaust Gas Recirculation Sensor "B" Circuit Low No. 2 EGR valve position sensor output voltage is less than 0.1 V for more than 5 seconds
(1 trip detection logic)
·

Open or short in No. 2 EGR valve position sensor circuit

·

No. 2 EGR valve (EGR valve position sensor)

·

ECM


Comes on DTC stored
P0408 Exhaust Gas Recirculation Sensor "B" Circuit High No. 2 EGR valve position sensor output voltage is more than 4.9 V for more than 5 seconds
(1 trip detection logic)
·

Open or short in No. 2 EGR valve position sensor circuit

·

No. 2 EGR valve (EGR valve position sensor)

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

When the output voltage of the EGR valve position sensor deviates from the normal operating range of 0.1 to 4.9 V for more than 0.5 seconds, the ECM interprets this as a malfunction of the sensor circuit, and illuminates the MIL.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (EGR VALVE POWER SOURCE)
a.
A165766C04
1.052,1.115 1.49,1.396 0.438,0.281 1.896,1.115 2.333,1.396 0.438,0.281 1.458,2.229 1.167,2.635 true 1.719,2.229 1.896,2.656 true 0.177,0.146 0.448,0.365 0.271,0.219 10 false *a 1.052,2.656 1.302,2.854 0.25,0.198 10 false E2 1.5,0.969 1.688,1.146 0.188,0.177 10 false *1 2.365,0.969 2.552,1.146 0.188,0.177 10 false *2 1.156,1.177 1.469,1.354 0.313,0.177 10 false C47 1.99,1.177 2.302,1.354 0.313,0.177 10 false C66 1.833,2.677 2.083,2.875 0.25,0.198 10 false VC
*1 No. 1
*2 No. 2
*a Front view of wire harness connector
(to EGR Valve)


Disconnect the EGR valve connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
No. 1
Tester Connection Switch Condition Specified Condition
C47-3 (VC) - C47-2 (E2) Ignition switch ON 4.5 to 5.5 V

No. 2
Tester Connection Switch Condition Specified Condition
C66-3 (VC) - C66-2 (E2) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

2.INSPECT EGR VALVE ASSEMBLY (NO. 1 OR NO. 2) (POSITION SENSOR)

NG

3.CHECK HARNESS AND CONNECTOR (EGR VALVE - ECM)
2.INSPECT EGR VALVE ASSEMBLY (NO. 1 OR NO. 2) (POSITION SENSOR)
a.
A165764C02
1.385,2.156 1.115,2.521 true 2.031,2.156 2.271,2.51 true 1.698,2.156 1.708,2.521 true 0.906,2.552 1.323,2.719 0.417,0.167 10 false EGLS 2.24,2.521 2.458,2.688 0.219,0.167 10 false E2 0.271,0.219 0.583,0.375 0.313,0.156 10 false *a 1.615,2.563 1.833,2.729 0.219,0.167 10 false VC
*a Component without harness connected
(EGR Valve)


Disconnect the EGR valve connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
3 (VC) - 2 (E2) 20°C (68°F) 2.45 to 4.55 kΩ
4 (EGLS) - 2 (E2) 20°C (68°F) 2.45 to 4.55 kΩ



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (EGR VALVE - ECM)

NG

REPLACE EGR VALVE ASSEMBLY (NO. 1 OR NO. 2)

3.CHECK HARNESS AND CONNECTOR (EGR VALVE - ECM)
a.
A311467C04
1.135,0.375 1.552,0.635 0.417,0.26 1.875,0.375 2.292,0.635 0.417,0.26 1.323,2.375 1.74,2.635 0.417,0.26 2.208,1.698 1.917,1.24 true 0.271,4.281 0.521,3.583 true 0.979,4.25 0.615,3.594 true 1.708,1.688 1.708,1.229 true 1.292,1.677 1.479,1.229 true 1.688,4.281 0.698,3.594 true 0.781,3.583 0.646,2.677 true 1.583,0.208 1.896,0.365 0.313,0.156 10 false *1 2.313,0.219 2.625,0.375 0.313,0.156 10 false *2 0.198,0.156 0.51,0.313 0.313,0.156 10 false *a 0.219,2.115 0.531,2.271 0.313,0.156 10 false *b 1.219,0.427 1.531,0.583 0.313,0.156 10 false C47 1.958,0.427 2.271,0.583 0.313,0.156 10 false C66 2.135,1.708 2.656,1.854 0.521,0.146 10 false EGLS 1.406,2.427 1.719,2.583 0.313,0.156 10 false C39 1.635,4.302 2.51,4.51 0.875,0.208 10 false 89 (EGLS) 0.26,2.49 1.135,2.698 0.875,0.208 10 false 90 (VCEG) 1.615,1.708 1.927,1.865 0.313,0.156 10 false VC 1.177,1.698 1.49,1.854 0.313,0.156 10 false E2 0.063,4.292 0.938,4.5 0.875,0.208 10 false 87 (EEGL) 0.833,4.302 1.708,4.51 0.875,0.208 10 false 88 (EGS2)
*1 No. 1
*2 No. 2
*a Front view of wire harness connector
(to EGR Valve)
*b Front view of wire harness connector
(to ECM)


Disconnect the EGR valve connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
No. 1
Tester Connection Condition Specified Condition
C47-3 (VC) - C39-90 (VCEG) Always Below 1 Ω
C47-4 (EGLS) - C39-89 (EGLS) Always Below 1 Ω
C47-2 (E2) - C39-87(EEGL) Always Below 1 Ω
C47-3 (VC) or C39-90 (VCEG) - Body ground Always 10 kΩ or higher
C47-4 (EGLS) or C39-89 (EGLS) - Body ground Always 10 kΩ or higher

No. 2
Tester Connection Condition Specified Condition
C66-3 (VC) - C39-90 (VCEG) Always Below 1 Ω
C66-4 (EGLS) - C39-88 (EGS2) Always Below 1 Ω
C66-2 (E2) - C39-87 (EEGL) Always Below 1 Ω
C66-3 (VC) or C39-90 (VCEG) - Body ground Always 10 kΩ or higher
C66-4 (EGLS) or C39-88 (EGS2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR