Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM › from 2017.09
RM25T0E _51 Engine / Hybrid System _029760 1VD-FTV ENGINE CONTROL _0135360 ECD SYSTEM C

1VD-FTV ENGINE CONTROL  ECD SYSTEM  P0400  Exhaust Gas Recirculation Flow  P1248  Exhaust Gas Recirculation Flow Bank 2  


DESCRIPTION

The EGR system recirculates exhaust gases. The recirculated gas mingles with the intake air so that the EGR system can slow the combustion speed and keep the combustion temperature down. This helps reduce NOx emissions.

In order to increase EGR circulation efficiency, the ECM adjusts the EGR valve angle and the throttle valve angle.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0400 Exhaust Gas Recirculation Flow When one of the following conditions is met:
·

Target and actual positions of the electric EGR control valve are different

(1 trip detection logic)

·

Mass air flow rate is not changed when turning on electric EGR control valve

(2 trip detection logic)


·

EGR valve stuck

·

EGR valve does not move smoothly

·

EGR cooler

·

Mass air flow meter sub-assembly

·

Open or short inEGR valve circuit

·

EGR valve deposit


Comes on DTC stored
P1248 Exhaust Gas Recirculation Flow Bank 2 Target and actual positions of the electric EGR control valve are different
(1 trip detection logic)
·

EGR valve stuck

·

EGR valve does not move smoothly

·

EGR cooler

·

Mass air flow meter sub-assembly

·

Open or short inEGR valve circuit

·

EGR valve deposit


Comes on DTC stored

Related Data List
DTC No. Data List
P0400
P1248
·

MAF

·

Target EGR Position

·

Actual EGR Valve Pos.



CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0400 After warming up the engine, decelerate from a speed of 80 km/h (50 mph) or more (fully release the accelerator pedal for approximately 5 seconds).
P1248 After warming up engine and idling for 60 seconds, maintain engine speed at 2500 rpm for 40 seconds, drive vehicle, and perform engine brake deceleration by fully releasing accelerator when engine speed is 2000 rpm or more.

MONITOR DESCRIPTION

If the electric EGR control valve assembly is forcibly operated during deceleration but the intake air amount does not vary, the ECM determines that the electric EGR control valve assembly is malfunctioning. The ECM then illuminates the MIL (2 trip detection logic).

A194528E11
3.24,2.333 3.344,2.031 3.344,2.031 3.469,2.031 false 3.25,0.729 3.354,0.427 3.354,0.427 3.479,0.427 false 5.042,3.521 5.344,3.521 false 5.083,4.292 5.271,4.188 5.271,4.188 5.344,4.188 false 4.781,4.771 4.958,4.896 4.958,4.896 5.042,4.896 false 0.073,1.771 1.427,2 1.354,0.229 10 false Accelerator Opening 0.146,0.646 1.5,0.875 1.354,0.229 10 false Vehicle Speed 0.083,3.198 1.438,3.427 1.354,0.229 10 false EGR Valve Opening 0.094,4.271 2.188,4.5 2.094,0.229 10 false Mass Air Flow Meter Output 0.094,4.5 1.656,5.052 1.563,0.552 10 false (Changing Value of Intake Air Amount: gm/s) 1.469,2.229 2.042,2.479 0.573,0.25 10 false Closed 1.552,1.583 2.125,1.833 0.573,0.25 10 false Open 1.479,3.563 2.052,3.813 0.573,0.25 10 false Closed 1.531,2.875 2.104,3.125 0.573,0.25 10 false Open 3.51,1.948 5.542,2.156 2.031,0.208 10 false Fully Closed 3.51,0.354 5.542,0.563 2.031,0.208 10 false During Deceleration 5.396,3.438 6.281,3.646 0.885,0.208 10 false Fully Closed 5.375,4.135 6.031,4.375 0.656,0.24 10 false Normal 5.115,4.813 5.771,5.052 0.656,0.24 10 false Abnormal 6.49,5.01 6.906,5.302 0.417,0.292 10 false Time 0.125,0.083 1.448,0.333 1.323,0.25 10 false Flow Malfunction:

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0400, P1248)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes

Powertrain > Engine and ECT > Trouble Codes
50001 61

d.

Read the DTCs.

Result:
Result Proceed to
P0400 and/or P1248 are output A
P0400, P1248 and other DTCs are output B


HINT:

If codes other than P0400 and P1248 are output, perform troubleshooting for those DTCs first.




A

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)

B

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position / Data List / Target EGR Valve Pos. and Actual EGR Valve Pos.

Powertrain > Engine and ECT > Active Test
Active Test Display
Control the EGR Step Position
Data List Display
Target EGR Pos.
Actual EGR Valve Pos.
50004 61 95 596,578

e.

When changing the Active Test value for 1, 30, 60, 90, 60, 30 and 1%, check that Actual EGR Valve Pos smoothly changes to the set opening angle.

OK:

The Actual EGR Valve Pos value follows the Target EGR Valve Pos value.



Result:
Proceed to
OK
NG



OK

3.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE EGR VALVE CLOSE)

NG

11.REPLACE ELECTRIC EGR CONTROL VALVE ASSEMBLY
3.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE EGR VALVE CLOSE)
a.

Connect the GTS to the DLC3.


b.

Start the engine and warm it up, and make sure the A/C switch and all accessory switches are off.


c.

Turn the ignition switch off. Wait for 30 seconds, and then restart the engine.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / MAF.

Powertrain > Engine and ECT > Data List
Tester Display
MAF
50003 61 319

f.

Read the MAF value displayed on the GTS while the engine is idling.


g.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the EGR Valve Close / Data List / MAF.

Powertrain > Engine and ECT > Active Test
Active Test Display
Activate the EGR Valve Close
Data List Display
MAF
50004 61 183 319

h.

Read the MAF value when the EGR valve is closed using the Active Test function.

HINT:
·

If idling continues for 20 minutes or more, the EGR valve target opening angle becomes 0% (EGR valve fully closed). As this makes diagnosis impossible, it becomes necessary to drive the vehicle or to restart the engine.

·

Before performing the diagnosis, confirm that the EGR valve target opening angle is not 0%.

·

When idling the engine, the EGR cooler sub-assembly is bypassed.



Result:
Active Test Result Proceed to
Activate the EGR Valve Close:
Off (Open) to On (Closed)
MAF value does not change A
MAF value changes B


NOTICE:

As the measured values may differ from those shown below due to factors such as differences in measuring environments and changes in vehicle condition due to aging, do not use these values to determine whether the vehicle is malfunctioning or not.


HINT:

The problem may be a temporary one, due to the entry of deposits or foreign matter. Check that there are no deposits or foreign matter in the electric EGR control valve assembly or mass air flow meter sub-assembly.


Reference:
EGR Valve Condition (Opening) Measuring Condition MAF (Reference)
Open (50%)
·

Atmosphere pressure: 101 kPa

·

Engine coolant temperature: 75°C (167°F)


3 to 10 gm/sec
Closed (0%) 14 to 23 gm/sec




A

4.READ VALUE USING GTS (MAF AND ENGINE SPEED)

B

9.CLEAN EGR VALVE ASSEMBLY
4.READ VALUE USING GTS (MAF AND ENGINE SPEED)
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / MAF.

Powertrain > Engine and ECT > Data List
Tester Display
Engine Speed
MAF
50003 61 315,319

d.

Start the engine and read the value when 30 seconds has elapsed.

Standard:
Engine speed MAF
Idling 6.1 to 26.5 gm/sec
3000 rpm 68.0 to 170.0 gm/sec



Result:
Proceed to
OK
NG



OK

5.CHECK FOR DEPOSIT (ELECTRIC EGR CONTROL VALVE ASSEMBLY)

NG

8.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY
5.CHECK FOR DEPOSIT (ELECTRIC EGR CONTROL VALVE ASSEMBLY)
a.

Remove the electric EGR control valve assembly.

Click hereEngine / Hybrid System>1VD-FTV (EMISSION CONTROL)>EGR VALVE (w/o DPF)>REMOVAL


b.

Visually check the electric EGR control valve assembly for deposits. If there are deposits, clean the electric EGR control valve assembly.

NOTICE:
·

When cleaning the electric EGR control valve, make sure the valve is completely closed.

·

Do not forcibly open the valve, as it may be damaged or deformed.

·

When cleaning the electric EGR control valve, use a piece of cloth soaked with cleaning solvent. Spraying the solvent directly onto these parts or soaking the parts in the solvent may damage the parts.

·

When cleaning the EGR control valve, care should be taken to prevent the ingress of cleaning solvent into the bearings of valve shaft, and when wiping off deposits on the EGR control valve, care should be taken not to push the deposits into the bearings of the valve shaft. These contaminants may adversely affect the function of the EGR control valve.



HINT:
·

If the EGR valve does not open properly or is stuck closed, the amount of intake air increases and combustion sounds and engine vibration may increase.

·

If the EGR valve does not close properly or is stuck open, EGR becomes excessive and combustion becomes unstable. Also, there may be a lack of power.




c.

Reinstall the electric EGR control valve assembly.

Click hereEngine / Hybrid System>1VD-FTV (EMISSION CONTROL)>EGR VALVE (w/o DPF)>INSTALLATION


Result:
Proceed to
NEXT



NEXT

6.REPLACE EGR COOLER ASSEMBLY
6.REPLACE EGR COOLER ASSEMBLY

Result:
Proceed to
NEXT



NEXT

7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0400)
7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0400)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 61

d.

Turn the ignition switch off for 30 seconds or more.


e.

Start the engine and warm it up.


f.

Move the shift lever to 2nd gear and decelerate from a speed of 80 km/h (50 mph) or more (fully release the accelerator for approximately 5 seconds or more).


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 61

h.

Read the DTCs.

HINT:

When a DTC is output, the mass air flow meter may be malfunctioning.



Result:
Proceed to
NEXT



NEXT

END

8.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY
a.

Replace the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>MASS AIR FLOW METER(w/o DPF)>REMOVAL

HINT:

If foreign matter is stuck inside the mass air flow meter sub-assembly, the output characteristics of the mass air flow meter sub-assembly may change, resulting in a malfunction.



Result:
Proceed to
NEXT



NEXT

7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0400)
9.CLEAN EGR VALVE ASSEMBLY
a.

Remove the electric EGR control valve assembly.

Click hereEngine / Hybrid System>1VD-FTV (EMISSION CONTROL)>EGR VALVE (w/o DPF)>REMOVAL


b.

Visually check the electric EGR control valve assembly for deposits. If there are deposits, clean the electric EGR control valve assembly.

NOTICE:
·

When cleaning the electric EGR control valve, make sure the valve is completely closed.

·

Do not forcibly open the valve, as it may be damaged or deformed.

·

When cleaning the electric EGR control valve, use a piece of cloth soaked with cleaning solvent. Spraying the solvent directly onto these parts or soaking the parts in the solvent may damage the parts.

·

When cleaning the EGR control valve, care should be taken to prevent the ingress of cleaning solvent into the bearings of valve shaft, and when wiping off deposits on the EGR control valve, care should be taken not to push the deposits into the bearings of the valve shaft. These contaminants may adversely affect the function of the EGR control valve.



HINT:
·

If the EGR valve does not open properly or is stuck closed, the amount of intake air increases and combustion sounds and engine vibration may increase.

·

If the EGR valve does not close properly or is stuck open, EGR becomes excessive and combustion becomes unstable. Also, there may be a lack of power.




c.

Reinstall the electric EGR control valve assembly.

Click hereEngine / Hybrid System>1VD-FTV (EMISSION CONTROL)>EGR VALVE (w/o DPF)>INSTALLATION


Result:
Proceed to
NEXT



NEXT

10.CHECK WHETHER DTC OUTPUT RECURS (DTC P0400)
10.CHECK WHETHER DTC OUTPUT RECURS (DTC P0400)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 61

d.

Turn the ignition switch off for 30 seconds or more.


e.

Start the engine and warm it up.


f.

After warming up engine and idling for 60 seconds, maintain engine speed at 2500 rpm for 40 seconds, drive vehicle, and perform engine brake deceleration by fully releasing accelerator when engine speed is 2000 rpm or more.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 61

h.

Read the DTCs.

HINT:

When a DTC is output, the mass air flow meter may be malfunctioning.



Result:
Proceed to
NEXT



NEXT

END

11.REPLACE ELECTRIC EGR CONTROL VALVE ASSEMBLY
a.

Replace the electric EGR control valve assembly.

Click hereEngine / Hybrid System>1VD-FTV (EMISSION CONTROL)>EGR VALVE (w/o DPF)>REMOVAL

HINT:

Before replacing the electric EGR control valve assembly, check the connections of the wire harness and connectors. If there is any abnormality, replace or repair the wire harness or connector.



Result:
Proceed to
NEXT



NEXT

10.CHECK WHETHER DTC OUTPUT RECURS (DTC P0400)