| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0627 | Fuel Pump Control Circuit / Open | Open or short in suction control valve circuit for more than 0.5 seconds (1 trip detection logic) |
·
Open or short in suction control valve circuit
·
Suction control valve
·
Fuel temperature sensor, suction control valve wire
·
ECM |
Comes on | DTC stored |
For more information on the fuel supply pump (suction control valve) and the common rail system, refer to the system description.
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>SYSTEM DESCRIPTION
When DTC P0627 is set, check the internal fuel pressure of the common rail by entering the following menus on the GTS: Powertrain / Engine and ECT / Data List / Fuel Press.
| Engine Speed | Fuel Pressure |
|---|---|
| Idling | Approximately 27000 to 37000 kPa |
| 2500 rpm (No engine load) | Approximately 50000 to 70000 kPa |
Refer to DTC P0088.
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>P0088
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).
After replacing the fuel supply pump, the ECM needs initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
| *a | Component without harness connected (Fuel Temperature Sensor, Suction Control Valve) |
Disconnect the fuel temperature sensor, suction control valve connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| rC1-1 (PCV) - rC1-2 (+B) | 20°C (68°F) | 1.9 to 2.3 Ω |
| Proceed to |
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector (to Fuel Temperature Sensor, Suction Control Valve) |
| *b | Front view of wire harness connector (to ECM) |
Disconnect the fuel temperature sensor, suction control valve connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| rC1-1 (PCV) - C39-105 (PCV-) | Always | Below 1 Ω |
| rC1-2 (+B) - C39-106 (PCV+) | Always | Below 1 Ω |
| rC1-1 (PCV) or C39-105 (PCV-) - Body ground | Always | 10 kΩ or higher |
| rC1-2 (+B) or C39-106 (PCV+) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch ON and turn the GTS ON.
Clear DTCs.
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch ON and wait for approximately 1 minute.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| P0627 is output | A |
| No output is output | B |
A
B
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>CHECK FOR INTERMITTENT PROBLEMS
| *a | Component without harness connected (Fuel Temperature Sensor, Suction Control Valve) |
| *b | Suction Control Valve Wire "A" |
| *c | Fuel Temperature Sensor, Suction Control Valve Wire "B" |
Remove the fuel temperature sensor, suction control valve wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| "A"-1 - "B"-2 (+B) | Always | Below 1 Ω |
| "A"-2 - "B"-1 (PCV) | Always | Below 1 Ω |
| "A"-1 or "B"-2 (+B) - Body ground | Always | 10 kΩ or higher |
| "A"-2 or "B"-1 (PCV) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
| OK |
| NG |
OK
NG