Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM › from 2017.09
RM25T0E _51 Engine / Hybrid System _029760 1VD-FTV ENGINE CONTROL _0135360 ECD SYSTEM C

1VD-FTV ENGINE CONTROL  ECD SYSTEM  P1238  Injector Malfunction  


DESCRIPTION

HINT:
·

For more information on the injector and the common rail system.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>SYSTEM DESCRIPTION

·

If DTC P1238 is present, refer to the Diagnostic Trouble Code (DTC) Table for Common Rail System.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>DIAGNOSTIC TROUBLE CODE CHART



The ECM detects combustion deterioration for a specific cylinder.

A311471C01
2.75,1.115 3.51,1.292 true 3.635,2.156 4.26,2.156 true 2.99,4.094 3.615,4.094 true 2.563,1.031 2.875,1.188 0.313,0.156 10 false *1 4.313,2.083 4.625,2.24 0.313,0.156 10 false *2 2.813,4.031 3.125,4.188 0.313,0.156 10 false *3 0.146,0.146 0.458,0.302 0.313,0.156 10 false *a
*1 Solenoid Valve *2 Piston
*3 Nozzle Needle - -
*a Injector Cross Section Diagram - -


HINT:
·

The cylinder, which has the compensation value for Injection Feedback Val #1, #2, #3, #4, #5, #6, #7 and #8 that varies from other cylinders, may be malfunctioning.

·

If DTC P0093 (fuel leaks from high-pressure area) is set simultaneously, a leakage malfunction of the cylinder has probably occurred.

·

If DTC P062D (open or short in the No. 1 injector driver (EDU) or injector circuit) is set simultaneously, there is probably a faulty circuit located between the ECM and the injector including the No. 1 EDU.

·

If DTC P062E (open or short in the No. 2 injector driver (EDU) or injector circuit) is set simultaneously, there is probably a faulty circuit located between the ECM and the injector including the No. 2 EDU.

·

If only DTC P1238 (injector malfunction) is present, an injector mechanical malfunction or insufficient compression (valve clearance, etc.) has probably occurred. An open or short malfunction of the ECM, EDU or injector circuit is unlikely.



DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1238 Injector Malfunction Engine speed fluctuation is large when idling
(2 trip detection logic)
Main Trouble Area
·

Fuel Injector

·

Injector driver (EDU) (P062D and/or P062E set simultaneously)

·

Open or short in engine wire harness (P062D and/or P062E set simultaneously)

·

Connector connection (P062D and/or P062E set simultaneously)

·

Compression pressure


Related Trouble Area
·

Valve timing

·

Fuel with low cetane number used

·

ECM


Comes on DTC stored

HINT:

After confirming DTC P1238, check the internal fuel pressure on the GTS by entering the following menus: Powertrain / Engine and ECT / Data List / Fuel Press.

Reference
Engine Speed Fuel Pressure
Idling Approximately 27000 to 37000 kPa
2500 rpm (No engine load) Approximately 50000 to 70000kPa


MONITOR DESCRIPTION

P1238 (Injection malfunction, except open or short in injector circuit):

This DTC will be set if the engine speed fluctuation between each cylinder is large. The ECM monitors changes in the crankshaft rotation speed using the crankshaft position sensor in order to detect improper combustion. The camshaft position sensor also plays a role in determining which cylinder has the problem. The fluctuation counter increases when irregular crankshaft rotation speed variation exceeds the threshold with the engine idling. Therefore, if any one of the cylinders is operating poorly (rough idle), the ECM sets this DTC.


WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

After replacing an injector, the ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).


HINT:
·

If DTCs other than P1238 are present simultaneously, first troubleshoot those DTCs.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P1238)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch ON and turn the GTS ON.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 61

d.

Read DTCs.

Result:
Result Proceed to
P1238 is output A
P1238 and other DTCs are output B


HINT:
·

If any DTCs other than P1238 are output, troubleshoot those DTCs first.

·

If DTCs other than P1238 are not output, check the fuel condition before proceeding to next step.





A

2.CHECK HARNESS AND CONNECTOR (ENGINE WIRE HARNESS)

B

2.CHECK HARNESS AND CONNECTOR (ENGINE WIRE HARNESS)
a.

Check the wire harness and connector connections.

OK:

The wire harness and connectors have been connected securely and there are good connections.



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (COMPENSATORY INJECTION VOLUME FOR EACH CYLINDER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.READ VALUE USING GTS (COMPENSATORY INJECTION VOLUME FOR EACH CYLINDER)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch ON and turn the GTS ON.


c.

Start the engine and warm it up.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Injection Feedback Val #1 to #8.

Powertrain > Engine and ECT > Data List
Tester Display
Injection Feedback Val #1
Injection Feedback Val #2
Injection Feedback Val #3
Injection Feedback Val #4
Injection Feedback Val #5
Injection Feedback Val #6
Injection Feedback Val #7
Injection Feedback Val #8
50003 61 368,369,370,371,372,373,374,375

e.

Read the value.

Standard value:

The compensatory injection volume is between -3.0 mm3/st and 3.0 mm3/st.


HINT:
·

If the injector is malfunctioning, the compensatory injection volume remains at -5.0 mm3/st or 5.0 mm3/st.

·

The compensatory injection volume is usually between -3.0 mm3/st and 3.0 mm3/st.




f.

Any cylinders that have a higher compensatory injection volume than shown above are considered to be faulty. Use the following steps to inspect and repair the cylinders.


Result:
Result Proceed to
Faulty cylinder is not identified A
Faulty cylinder is identified B



B

4.PERFORM ACTIVE TEST USING GTS (FUEL CUT FOR IDENTIFYING MALFUNCTION CYLINDER)

A

7.REPLACE INJECTOR ASSEMBLY
4.PERFORM ACTIVE TEST USING GTS (FUEL CUT FOR IDENTIFYING MALFUNCTION CYLINDER)
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS ON.


c.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Select Cylinder Fuel Cut.

Powertrain > Engine and ECT > Active Test
Tester Display
Control the Select Cylinder Fuel Cut
50004 61 231

d.

Check the 8 cylinders in sequence to identify a faulty cylinder by performing the power-balance inspection.

HINT:
·

If the engine idle speed does not change when an injector is disabled, the cylinder being tested is malfunctioning.

·

If the cylinder being tested is normal, there will be a significant change in idle speed when the fuel injection is stopped for that cylinder.




Result:
Proceed to
NEXT



NEXT

5.CHECK CYLINDER COMPRESSION PRESSURE OF MALFUNCTIONING CYLINDER
5.CHECK CYLINDER COMPRESSION PRESSURE OF MALFUNCTIONING CYLINDER
a.

Check the cylinder compression pressure.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

6.CHECK WHETHER DTC OUTPUT RECURS (DTC P1238)

NG

CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION

6.CHECK WHETHER DTC OUTPUT RECURS (DTC P1238)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch ON and turn the GTS ON.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Clear.

Powertrain > Engine and ECT > Clear DTCs
50002 61

d.

Clear DTCs.

HINT:

Before clearing DTCs, save the data stored in the ECM memory if necessary.



e.

Switch the ECM from normal mode to check mode.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>CHECK MODE PROCEDURE


f.

Start the engine and warm it up.


g.

Allow the engine to idle for 60 seconds or more.


h.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 61

i.

Read DTCs.

Result:
Result Proceed to
P1238 is output A
No DTC is output B




A

7.REPLACE INJECTOR ASSEMBLY

B

7.REPLACE INJECTOR ASSEMBLY

Result:
Proceed to
NEXT



NEXT

8.CHECK WHETHER DTC OUTPUT RECURS (DTC P1238)
8.CHECK WHETHER DTC OUTPUT RECURS (DTC P1238)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch ON and turn the GTS ON.



d.

Switch the ECM from normal mode to check mode.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>CHECK MODE PROCEDURE


e.

Start the engine and warm it up.


f.

Let the engine idle for 10 minutes.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 61

h.

Read DTCs.

Result:
Result Proceed to
P1238 is output A
No DTC is output B




A

B

END