The injector driver drives the injectors at high speeds with a high-voltage DC/DC converter. The ECM constantly monitors the injector driver and stops the engine if an abnormal condition is detected.
Refer to DTC P062D.
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>P062D
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
| *1 | No. 1 |
| *2 | No. 2 |
| *a | Front view of wire harness connector (to EDU) |
Disconnect the No. 1 injector driver (EDU) connectors.
Disconnect the No. 2 injector driver (EDU) connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C55-8 (+B) - C54-1 (GND) | Ignition switch ON | 11 to 14 V |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C53-8 (+B) - C52-1 (GND) | Ignition switch ON | 11 to 14 V |
| Proceed to |
| OK |
| NG |
OK
NG
Inspect the EDU relay (EDU 1 or EDU 2).
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION
| Proceed to |
| OK |
| NG |
OK
NG
Inspect the MAIN or MAIN 2 relay.
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION
| Proceed to |
| OK |
| NG |
OK
NG
Remove the EDU relay (EDU 1) from the engine room R/B assembly.
Remove the MAIN relay (MAIN) from the engine room R/B assembly.
Disconnect the cable from the negative (-) battery terminal.
Disconnect the cable from the positive (+) battery terminal.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| EDU 1 relay terminal 3 - MAIN relay terminal 3 | Always | Below 1 Ω |
| MAIN relay terminal 5 - Battery positive (+) terminal | Always | Below 1 Ω |
| EDU 1 relay terminal 3 or MAIN relay terminal 3 - Body ground | Always | 10 kΩ or higher |
| MAIN relay terminal 5 - Body ground | Always | 10 kΩ or higher |
Remove the EDU relay (EDU 2) from the engine room R/B assembly.
Remove the MAIN relay (MAIN2) from the engine room R/B assembly.
Disconnect the cable from the negative (-) battery terminal.
Disconnect the cable from the positive (+) battery terminal.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| EDU 2 relay terminal 3 - MAIN 2 relay terminal 3 | Always | Below 1 Ω |
| MAIN 2 relay terminal 5 - Battery positive (+) terminal | Always | Below 1 Ω |
| EDU 2 relay terminal 3 or MAIN 2 relay terminal 3 - Body ground | Always | 10 kΩ or higher |
| MAIN 2 relay terminal 5 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
| OK |
| NG |
OK
NG
Remove the EDU relay (EDU 1 or EDU 2) from the engine room R/B assembly.
Remove the EDU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C55-8 (+B) - EDU 1 relay terminal 5 | Always | Below 1 Ω |
| C55-8 (+B) or EDU 1 relay terminal 5 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C53-8 (+B) - EDU 2 relay terminal 5 | Always | Below 1 Ω |
| C53-8 (+B) or EDU 2 relay terminal 5 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
| OK |
| NG |
OK
NG
Remove the EDU relay (EDU 1 or EDU 2) from the engine room R/B assembly.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A29-45 (IREL) - EDU 1 relay terminal 2 | Always | Below 1 Ω |
| A29-45 (IREL) or EDU 1 relay terminal 2 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I84-45 (IREL) - EDU 1 relay terminal 2 | Always | Below 1 Ω |
| I84-45 (IREL) or EDU 1 relay terminal 2 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A29-46 (IRL2) - EDU 2 relay terminal 2 | Always | Below 1 Ω |
| A29-46 (IRL2) or EDU 2 relay terminal 2 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I84-46 (IRL2) - EDU 2 relay terminal 2 | Always | Below 1 Ω |
| I84-46 (IRL2) or EDU 2 relay terminal 2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
| OK |
| NG |
OK
NG
Remove the EDU relay (EDU 1) from the engine room R/B assembly.
Remove the MAIN relay (MAIN) from the engine room R/B assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| EDU 1 relay terminal 1 - MAIN relay terminal 3 | Always | Below 1 Ω |
| EDU 1 relay terminal 1 or MAIN relay terminal 3 - Body ground | Always | 10 kΩ or higher |
Remove the EDU relay (EDU 2) from the engine room R/B assembly.
Remove the MAIN relay (MAIN2) from the engine room R/B assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| EDU 2 relay terminal 1 - MAIN2 relay terminal 3 | Always | Below 1 Ω |
| EDU 2 relay terminal 1 or MAIN2 relay terminal 3 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
| OK |
| NG |
OK
NG
Disconnect the EDU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C54-1 (GND) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C52-1 (GND) - Body ground | Always | Below 1 Ω |
| Proceed to |
| OK |
| NG |
OK
NG