Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o EGR System) › from 2019.09
RM25T0E _51 Engine / Hybrid System _029760 1VD-FTV ENGINE CONTROL _0309414 ECD SYSTEM(w/o EGR System) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/o EGR System)  P0110  Intake Air Temperature Circuit  P0112  Intake Air Temperature Circuit Low Input  P0113  Intake Air Temperature Circuit High Input  


DESCRIPTION

The intake air temperature sensor is built into the mass air flow (MAF) meter and senses the intake air temperature.

A thermistor built into the sensor changes its resistance value according to the intake air temperature.

The lower the intake air temperature, the greater the thermistor resistance value. The higher the intake air temperature, the lower the thermistor resistance value (see Fig. 1).

The intake air temperature sensor is connected to the ECM.

The 5 V power source voltage in the ECM is applied to the intake air temperature sensor from terminal THA via resistor R.

The resistor R and the intake air temperature sensor are connected in series. When the resistance value of the intake air temperature sensor changes in accordance with changes in the intake air temperature, the potential at terminal THA also changes. Based on this signal, the ECM increases the fuel injection volume to improve driveability with a cold engine.

A208462E01
1.469,2 1.625,1.76 1.625,1.76 1.771,1.76 false 0.208,0.146 0.906,0.49 0.698,0.344 10 false (Fig. 1) 0.208,0.542 1.313,0.823 1.104,0.281 10 false Resistance kΩ 1.823,1.688 2.656,2.031 0.833,0.344 10 false Acceptable 1.208,4.073 2.521,4.385 1.313,0.313 10 false Temperature °C (°F)

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0110 Intake Air Temperature Circuit Open or short in intake air temperature (IAT) sensor circuit for 0.5 seconds
(1 trip detection logic)
·

Open or short in intake air temperature (IAT) sensor circuit

·

IAT sensor (built into mass air flow meter)

·

ECM


Comes on DTC stored
P0112 Intake Air Temperature Circuit Low Input Short in IAT sensor circuit for 0.5 seconds
(1 trip detection logic)
·

Open in IAT sensor circuit

·

IAT sensor (built into mass air flow meter)

·

ECM


Comes on DTC stored
P0113 Intake Air Temperature Circuit High Input Open in IAT sensor circuit for 0.5 seconds
(1 trip detection logic)
·

Open in IAT sensor circuit

·

IAT sensor (built into mass air flow meter)

·

ECM


Comes on DTC stored

HINT:

When DTC P0110, P0112 or P0113 is detected, check the intake air temperature by entering the following menus on the GTS: Powertrain / Engine and ECT / Data List / Intake Air.


Reference
Temperature Displayed Malfunction
-40°C (-40°F) Open circuit
140°C (284°F) or higher Short circuit

WIRING DIAGRAM

A165735E11
0.583,2.448 0.875,2.604 0.292,0.156 10 false C41 0.583,2.604 2.594,2.958 2.01,0.354 10 false Intake Air Temperature Sensor (Built into Mass Air Flow Meter) 6,2.677 6.292,2.833 0.292,0.156 10 false C39 6,2.833 6.354,3.01 0.354,0.177 10 false ECM 2.177,1.646 2.406,1.823 0.229,0.177 10 false E2 2.458,1.656 2.583,1.833 0.125,0.177 10 false 5 2.073,1.031 2.417,1.208 0.344,0.177 10 false THA 5.542,1.646 5.771,1.823 0.229,0.177 10 false E2 5.542,1.031 5.885,1.208 0.344,0.177 10 false THA 2.458,1.042 2.583,1.219 0.125,0.177 10 false 4 5.292,1.635 5.49,1.813 0.198,0.177 10 false 75 5.302,1.031 5.49,1.208 0.188,0.177 10 false 71 6.156,0.917 6.281,1.073 0.125,0.156 10 false R 6.25,0.635 6.51,0.802 0.26,0.167 10 false 5V

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR System)>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR System)>INITIALIZATION).


HINT:
·

If DTCs relating to different systems are output, and they share terminal E2 as their ground, check this ground circuit first.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING GTS (INTAKE AIR TEMPERATURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.

Powertrain > Engine and ECT > Data List
Tester Display
Intake Air
50003 61 318

d.

Read the value.

Standard value:

Same as actual intake air temperature.


Result:
Result Proceed to
-40°C (-40°F) A
140°C (284°F) or higher B
OK (same as actual intake air temperature) C


HINT:
·

If there is an open circuit, the GTS indicates -40°C (-40°F).

·

If there is a short circuit, the GTS indicates 140°C (284°F) or more.





A

2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)

B

4.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)

C

2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)
a.
A311460C02
1.552,2.833 1.948,3.104 0.396,0.271 1.188,4.396 1.854,3.854 true 2.417,4.406 2.115,3.865 true 0.708,1.771 0.927,1.969 0.219,0.198 10 false *1 2.635,1.771 2.854,1.969 0.219,0.198 10 false *2 0.25,2.667 0.469,2.865 0.219,0.198 10 false *a 1.625,2.885 1.958,3.083 0.333,0.198 10 false C41 1.021,4.406 1.354,4.604 0.333,0.198 10 false THA 2.375,4.417 2.708,4.615 0.333,0.198 10 false E2 2.438,1.063 2.771,1.26 0.333,0.198 10 false THA 2.438,1.427 2.771,1.625 0.333,0.198 10 false E2
*1 Mass Air Flow Meter
*2 ECM
*a Front view of wire harness connector
(to Mass Air Flow Meter)


Disconnect the mass air flow meter connector.


b.

Connect terminals 4 (THA) and 5 (E2) of the mass air flow meter wire harness side connector.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON and turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.

Powertrain > Engine and ECT > Data List
Tester Display
Intake Air
50003 61 318

f.

Read the value.

Standard value:

140°C (284°F) or higher



Result:
Proceed to
OK
NG



OK

CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE MASS AIR FLOW METER

NG

3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.
A311459C07
1.531,0.188 1.948,0.5 0.417,0.313 1.323,2.302 1.74,2.615 0.417,0.313 0.781,4.146 1.135,3.5 true 1.865,4.135 1.479,3.479 true 2.323,1.771 2.125,1.208 true 1.667,1.781 1.854,1.198 true 0.135,0.094 0.448,0.292 0.313,0.198 10 false *a 0.177,2.146 0.49,2.344 0.313,0.198 10 false *b 1.615,0.271 1.927,0.469 0.313,0.198 10 false C41 1.406,2.375 1.719,2.573 0.313,0.198 10 false C39 0.448,4.177 1.156,4.375 0.708,0.198 10 false 71 (THA) 1.688,4.177 2.26,4.385 0.573,0.208 10 false 75 (E2) 2.281,1.823 2.531,1.99 0.25,0.167 10 false E2 1.552,1.823 1.865,1.99 0.313,0.167 10 false THA
*a Front view of wire harness connector
(to Mass Air Flow Meter)
*b Front view of wire harness connector
(to ECM)


Disconnect the mass air flow meter connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C41-4 (THA) - C39-71 (THA) Always Below 1 Ω
C41-5 (E2) - C39-75 (E2) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)
a.
A166688C01
0.583,2.083 0.823,2.281 0.24,0.198 10 false *1 2.667,2.302 2.906,2.5 0.24,0.198 10 false *2 2.385,1.417 2.76,1.615 0.375,0.198 10 false THA 2.396,1.771 2.771,1.969 0.375,0.198 10 false E2
*1 Mass Air Flow Meter
*2 ECM


Disconnect the mass air flow meter connector.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.

Powertrain > Engine and ECT > Data List
Tester Display
Intake Air
50003 61 318

e.

Read the value.

Standard value:

-40°C (-40°F)



Result:
Proceed to
OK
NG



OK

NG

5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.
A311459C08
1.531,0.188 1.948,0.5 0.417,0.313 1.323,2.302 1.74,2.615 0.417,0.313 0.781,4.146 1.135,3.49 true 2.354,1.823 1.938,1.219 true 0.135,0.094 0.448,0.292 0.313,0.198 10 false *a 0.177,2.146 0.49,2.344 0.313,0.198 10 false *b 1.615,0.271 1.927,0.469 0.313,0.198 10 false C41 1.406,2.375 1.719,2.573 0.313,0.198 10 false C39 0.448,4.177 1.156,4.375 0.708,0.198 10 false 71 (THA) 2.26,1.844 2.573,2.042 0.313,0.198 10 false THA
*a Front view of wire harness connector
(to Mass Air Flow Meter)
*b Front view of wire harness connector
(to ECM)


Disconnect the mass air flow meter connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C41-4 (THA) or C39-71 (THA) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR