A thermistor is built into the Engine Coolant Temperature (ECT) sensor and it changes its resistance value according to the engine coolant temperature.
The structure of the sensor and connection to the ECM is the same as the intake air temperature sensor.
If the ECM detects DTC P0117 or P0118, it operates the fail-safe function in which the ECT is assumed to be 113°C (235°F).
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0115 | Engine Coolant Temperature Circuit | Open or short in engine coolant temperature (ECT) sensor circuit for 0.5 seconds (1 trip detection logic) |
·
Open or short in engine coolant temperature (ECT) sensor circuit
·
ECT sensor
·
ECM |
Comes on | DTC stored |
| P0117 | Engine Coolant Temperature Circuit Low Input | Short in ECT sensor circuit for 0.5 seconds (1 trip detection logic) |
·
Short in ECT sensor circuit
·
ECT sensor
·
ECM |
Comes on | DTC stored |
| P0118 | Engine Coolant Temperature Circuit High Input | Open in ECT sensor circuit for 0.5 seconds (1 trip detection logic) |
·
Open in ECT sensor circuit
·
ECT sensor
·
ECM |
Comes on | DTC stored |
When DTC P0117 and/or P0118 is detected, check the engine coolant temperature by entering the following menus on the GTS: Powertrain / Engine and ECT / Data List / Coolant Temp.
| Temperature Displayed | Malfunction |
|---|---|
| -40°C (-40°F) | Open circuit |
| 140°C (284°F) or higher | Short circuit |
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P0115 P0117 P0118 |
Ignition switch ON for 0.5 seconds |
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR System)>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR System)>INITIALIZATION).
If DTCs relating to different systems are output, and they share terminal E2 as their ground, check this ground circuit first.
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.
| Tester Display |
|---|
| Coolant Temp |
Read the value.
75 to 90°C (167 to 194°F) with warm engine.
| Result | Proceed to |
|---|---|
| -40°C (-40°F) | A |
| 140°C (284°F) or higher | B |
| 75 to 90°C (167 to 194°F) | C |
If there is an open circuit, the GTS indicates -40°C (-40°F).
If there is a short circuit, the GTS indicates 140°C (284°F) or more.
A
B
C
| *1 | ECT Sensor |
| *2 | ECM |
| *a | Front view of wire harness connector (to ECT Sensor) |
Disconnect the engine coolant temperature sensor connector.
Connect terminals 1 and 2 of the ECT sensor wire harness side connector.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.
| Tester Display |
|---|
| Coolant Temp |
Read the value.
140°C (284°F) or higher
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the ECT sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C69-2 - C39-76 (THW) | Always | Below 1 Ω |
| C69-1 - C39-75 (E2) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | ECT Sensor |
| *2 | ECM |
Disconnect the ECT sensor connector.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.
| Tester Display |
|---|
| Coolant Temp |
| Tester Display |
|---|
| Coolant Temp |
Read the value.
-40°C (-40°F)
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the ECT sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C69-2 or C39-76 (THW) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG