Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o EGR System) › from 2019.09
RM25T0E _51 Engine / Hybrid System _029760 1VD-FTV ENGINE CONTROL _0309414 ECD SYSTEM(w/o EGR System) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/o EGR System)  P0122  Throttle / Pedal Position Sensor / Switch "A" Circuit Low Input  P0123  Throttle / Pedal Position Sensor / Switch "A" Circuit High Input  P0222  Throttle / Pedal Position Sensor / Switch "B" Circuit Low Input  P0223  Throttle / Pedal Position Sensor / Switch "B" Circuit High Input  


DESCRIPTION

The throttle position sensor is mounted on the diesel throttle body and detects the opening angle of the throttle valve. This sensor is an electronic sensor and uses Hall-effect elements.

When the throttle valve is fully closed, a voltage of approximately 0.7 V is applied to terminal VLU of the ECM. The voltage applied to terminal VLU of the ECM increases in proportion to the opening angle of the throttle valve and becomes approximately 3.5 to 4.0 V when the throttle valve is fully opened.

The ECM determines the vehicle's driving conditions from the signals input to its terminal VLU.

A128639E01
1.699,0.22 3.248,0.428 1.549,0.208 10 Throttle Position Sensor 2.898,2.955 3.438,3.156 0.540,0.201 10 Hall IC 4.372,0.59 4.778,0.798 0.407,0.208 10 ECM 4.386,1.016 4.676,1.217 0.290,0.201 10 5 V 3.499,1.116 3.938,1.317 0.439,0.201 10 VCVL 3.574,1.739 4.037,1.940 0.463,0.201 10 VLU 3.499,2.347 3.899,2.548 0.401,0.201 10 EVLU 3.145,1.116 3.407,1.317 0.262,0.201 10 VC 3.145,2.347 3.379,2.548 0.234,0.201 10 E2 3.145,1.739 3.513,1.940 0.368,0.201 10 VTA 1.687,2.975 2.278,3.182 0.591,0.207 10 Magnet 2.521,2.036 2.858,3.036 false 2.415,2.572 2.217,3.063 false 1.687,0.625 2.278,0.833 0.591,0.207 10 Magnet 2.217,0.743 2.415,1.234 false

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0122 Throttle / Pedal Position Sensor / Switch "A" Circuit Low Input Throttle position sensor (for Bank 1) output (VLU) is less than 0.2 V
(1 trip detection logic)
·

Throttle position sensor (for Bank 1)

·

Open or short in VLU circuit

·

Open in VC circuit

·

ECM


Comes on DTC stored
P0123 Throttle / Pedal Position Sensor / Switch "A" Circuit High Input Throttle position sensor (for Bank 1) output (VLU) is more than 4.8 V
(1 trip detection logic)
·

Throttle position sensor (for Bank 1)

·

Open in E2 circuit

·

VC and VLU circuits are short-circuited

·

ECM


Comes on DTC stored
P0222 Throttle / Pedal Position Sensor / Switch "B" Circuit Low Input Throttle position sensor (for Bank 2) output (VLU2) is less than 0.2 V
(1 trip detection logic)
·

Throttle position sensor (for Bank 2)

·

Open or short in VLU2 circuit

·

Open in VC circuit

·

ECM


Comes on DTC stored
P0223 Throttle / Pedal Position Sensor / Switch "B" Circuit High Input Throttle position sensor (for Bank 2) output (VLU2) is more than 4.8 V
(1 trip detection logic)
·

Throttle position sensor (for Bank 2)

·

Open in E2 circuit

·

VC and VLU2 circuits are short-circuited

·

ECM


Comes on DTC stored

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0122
P0123
P0222
P0223
Ignition switch ON for 3 seconds

MONITOR DESCRIPTION

When the output voltage of the throttle position sensor deviates from the normal operating range (between 0.2 V and 4.8 V) for more than 3 seconds, the ECM interprets this as a malfunction of the sensor circuit and illuminates the MIL.

C129051E09
2.302,1.063 1.99,1.229 false 2.302,2.656 1.99,2.823 false 4.917,0.5 4.615,1.031 false 4.615,2.688 4.917,3.219 false 0.083,0.042 2.885,0.24 2.802,0.198 10 false Throttle Position Sensor Output Voltage (V) 2.063,0.552 2.635,0.75 0.573,0.198 10 false Closed 4.979,0.406 6.469,0.604 1.49,0.198 10 false Detect P0123 or P0223 4.01,0.552 4.469,0.75 0.458,0.198 10 false Open 2.646,2.729 4.125,2.927 1.479,0.198 10 false Range of Operation 4.979,3.125 6.458,3.323 1.479,0.198 10 false Detect P0122 or P0222 2.323,3.406 4.229,3.635 1.906,0.229 10 false Throttle Valve Opening Angle 4.083,3.198 4.313,3.396 0.229,0.198 10 false 70 2.26,3.198 2.396,3.396 0.135,0.198 10 false 0 1.677,2.771 2.031,2.969 0.354,0.198 10 false 0.20 1.969,2.406 2.354,2.604 0.385,0.198 10 false 0.69 1.969,1.375 2.323,1.573 0.354,0.198 10 false 3.49 1.677,1.115 2.042,1.313 0.365,0.198 10 false 4.80 1.969,0.927 2.323,1.125 0.354,0.198 10 false 5.00

WIRING DIAGRAM

A165736E17
2.031,1.135 2.271,1.333 0.24,0.198 10 false VC 1.969,1.469 2.271,1.667 0.302,0.198 10 false VTA 2.052,1.823 2.281,2.021 0.229,0.198 10 false E2 5.26,1.146 5.688,1.344 0.427,0.198 10 false VCVL 5.26,1.458 5.563,1.656 0.302,0.198 10 false VLU 5.26,1.823 5.74,2.021 0.479,0.198 10 false EVLU 2.385,1.021 2.573,1.208 0.188,0.188 10 false 1 2.385,1.354 2.573,1.542 0.188,0.188 10 false 3 2.385,1.698 2.573,1.885 0.188,0.188 10 false 2 4.938,1.021 5.26,1.198 0.323,0.177 10 false 91 4.948,1.354 5.135,1.542 0.188,0.188 10 false 93 5.271,3.625 5.729,3.823 0.458,0.198 10 false VLU2 4.896,3.521 5.188,3.708 0.292,0.188 10 false 103 4.938,1.677 5.125,1.865 0.188,0.188 10 false 92 1.073,2.135 1.344,2.313 0.271,0.177 10 false C50 1.073,2.323 3.458,2.5 2.385,0.177 10 false Throttle Position Sensor (for Bank 1) 2.031,3.26 2.271,3.458 0.24,0.198 10 false VC 1.969,3.594 2.271,3.792 0.302,0.198 10 false VTA 2.052,3.958 2.281,4.156 0.229,0.198 10 false E2 2.385,3.167 2.573,3.354 0.188,0.188 10 false 1 2.385,3.51 2.573,3.698 0.188,0.188 10 false 3 2.385,3.844 2.573,4.031 0.188,0.188 10 false 2 1.073,4.302 1.344,4.479 0.271,0.177 10 false C65 1.073,4.49 3.448,4.667 2.375,0.177 10 false Throttle Position Sensor (for Bank 2) 5.656,4.625 5.948,4.802 0.292,0.177 10 false C39 5.656,4.792 6.021,4.969 0.365,0.177 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR System)>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR System)>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM)
a.
A311462C04
1.219,0.198 1.646,0.479 0.427,0.281 1.896,0.198 2.323,0.479 0.427,0.281 1.385,2.323 1.813,2.604 0.427,0.281 1.188,1.656 1.438,1.135 true 1.854,4.292 1.031,3.563 true 2.135,1.667 1.958,1.146 true 1,4.25 0.948,3.563 true 0.385,4.292 0.854,3.563 true 2.656,4.302 1.906,3.563 true 1.688,1.667 1.688,1.146 true 1.656,0.083 1.969,0.24 0.313,0.156 10 false *1 2.333,0.094 2.646,0.25 0.313,0.156 10 false *2 0.115,0.135 0.427,0.292 0.313,0.156 10 false *a 0.146,1.979 0.458,2.135 0.313,0.156 10 false *b 1.323,0.26 1.635,0.417 0.313,0.156 10 false C50 1.99,0.26 2.302,0.417 0.313,0.156 10 false C65 1.094,1.688 1.406,1.844 0.313,0.156 10 false VC 1.604,1.698 1.917,1.854 0.313,0.156 10 false E2 2.021,1.698 2.375,1.844 0.354,0.146 10 false VTA 0.083,4.344 0.865,4.531 0.781,0.188 10 false 91 (VCVL) 0.906,4.344 1.729,4.521 0.823,0.177 10 false 92 (EVLU) 1.74,4.333 2.406,4.531 0.667,0.198 10 false 93 (VLU) 2.552,4.333 3.292,4.542 0.74,0.208 10 false 103 (VLU2) 1.469,2.396 1.781,2.552 0.313,0.156 10 false C39
*1 for Bank 1
*2 for Bank 2
*a Front view of wire harness connector
(to Throttle Position Sensor)
*b Front view of wire harness connector
(to ECM)


Disconnect the throttle position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for Bank 1
Tester Connection Condition Specified Condition
C50-1 (VC) - C39-91 (VCVL) Always Below 1 Ω
C50-3 (VTA) - C39-93 (VLU) Always Below 1 Ω
C50-2 (E2) - C39-92 (EVLU) Always Below 1 Ω
C50-1 (VC) or C39-91 (VCVL) - Body ground Always 10 kΩ or higher
C50-3 (VTA) or C39-93 (VLU) - Body ground Always 10 kΩ or higher
C50-2 (E2) or C39-92 (EVLU) - Body ground Always 10 kΩ or higher

for Bank 2
Tester Connection Condition Specified Condition
C65-1 (VC) - C39-91 (VCVL) Always Below 1 Ω
C65-3 (VTA) - C39-103 (VLU2) Always Below 1 Ω
C65-2 (E2) - C39-92 (EVLU) Always Below 1 Ω
C65-1 (VC) or C39-91 (VCVL) - Body ground Always 10 kΩ or higher
C65-3 (VTA) or C39-103 (VLU2) - Body ground Always 10 kΩ or higher
C65-2 (E2) or C39-92 (EVLU) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK ECM TERMINAL VOLTAGE (VC TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK ECM TERMINAL VOLTAGE (VC TERMINAL)
a.
A165737C03
1.188,1.094 1.604,1.365 0.417,0.271 1.854,1.094 2.271,1.365 0.417,0.271 1.198,2.51 1.427,2.083 true 1.99,2.521 1.75,2.094 true 0.115,0.104 0.427,0.302 0.313,0.198 10 false *a 1.604,0.958 1.917,1.156 0.313,0.198 10 false *1 2.281,0.958 2.594,1.156 0.313,0.198 10 false *2 1.271,1.146 1.583,1.344 0.313,0.198 10 false C50 1.948,1.146 2.26,1.344 0.313,0.198 10 false C65 1.073,2.552 1.385,2.75 0.313,0.198 10 false VC 1.948,2.573 2.26,2.771 0.313,0.198 10 false E2
*1 for Bank 1
*2 for Bank 2
*a Front view of wire harness connector
(to Throttle Position Sensor)


Disconnect the throttle position sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for Bank 1
Tester Connection Switch Condition Specified Condition
C50-1 (VC) - C50-2 (E2) Ignition switch ON 4.5 to 5.5 V

for Bank 2
Tester Connection Switch Condition Specified Condition
C65-1 (VC) - C65-2 (E2) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

3.REPLACE DIESEL THROTTLE BODY ASSEMBLY (for Bank 1 or for Bank 2)

NG

3.REPLACE DIESEL THROTTLE BODY ASSEMBLY (for Bank 1 or for Bank 2)
a.

Replace the diesel throttle body assembly (for Bank 1 or Bank 2).

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>DIESEL THROTTLE BODY>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS
4.CHECK WHETHER DTC OUTPUT RECURS
a.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 61

b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and turn the GTS on.


d.

Start the engine.


e.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 61

f.

Read the DTCs.

Result:
Result Proceed to
P0122, P0123, P0222 and/or P0223 are output A
No DTC is output B




A

B

END