Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o EGR System) › from 2019.09
RM25T0E _51 Engine / Hybrid System _029760 1VD-FTV ENGINE CONTROL _0309414 ECD SYSTEM(w/o EGR System) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/o EGR System)  P0617  Starter Relay Circuit High  


DESCRIPTION

While the engine is being cranked, positive battery voltage is applied to terminal STA of the ECM.

If the ECM detects the starter control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and sets the DTC.

This monitor runs when the vehicle has been driven at 20 km/h (12.4 mph) for more than 20 seconds.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0617 Starter Relay Circuit High When positive (+B) battery voltage of 10.5 V or more applied to ECM, and conditions (a), (b) and (c) are met for 20 seconds
(1 trip detection logic):
(a) Vehicle speed is more than 20 km/h (12.4 mph)
(b) Engine speed is more than 1000 rpm
(c) STA signal is ON
·

Starter relay circuit

·

Ignition switch

·

ECM


Comes on DTC stored

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0617 Drive the vehicle for 25 seconds or more at a speed of 20 km/h (12.5 mph) or more and an engine speed of 1000 rpm or more

WIRING DIAGRAM

A225228E06
1.417,5.76 1.896,5.948 0.479,0.188 10 false Battery 2.677,5.646 3.146,5.813 0.469,0.167 10 false Starter 1.333,4.594 2.156,4.75 0.823,0.156 10 false FL MAIN 2.448,5.396 2.792,5.552 0.344,0.156 10 false D7 1.885,1.427 2.042,1.594 0.156,0.167 10 false 4 2.073,1.427 2.406,1.594 0.333,0.167 10 false AM1 2.031,1.792 2.365,1.958 0.333,0.167 10 false L21 2.031,1.938 2.99,2.104 0.958,0.167 10 false Ignition Switch 2.698,1.427 3.031,1.594 0.333,0.167 10 false ST1 3.083,1.427 3.24,1.594 0.156,0.167 10 false 3 3.042,3.781 3.198,3.948 0.156,0.167 10 false 5 3.604,3.781 3.76,3.948 0.156,0.167 10 false 1 3.042,4.594 3.198,4.76 0.156,0.167 10 false 3 3.583,4.594 3.74,4.76 0.156,0.167 10 false 2 3.802,2.625 4.031,2.813 0.229,0.188 10 false ST 3.979,4.146 4.25,4.302 0.271,0.156 10 false ST 5.021,3.26 5.25,3.427 0.229,0.167 10 false 48 5.677,5.635 5.969,5.802 0.292,0.167 10 false I84 5.677,5.813 6.042,5.979 0.365,0.167 10 false ECM 5.302,3.375 5.719,3.542 0.417,0.167 10 false STA 1.292,2.833 1.667,2.99 0.375,0.156 10 false ALT 1.313,2.094 1.729,2.25 0.417,0.156 10 false AM1 2.031,3.49 2.427,3.646 0.396,0.156 10 false AM2 3.073,5.146 3.344,5.302 0.271,0.156 10 false D6 2.5,5.177 2.656,5.344 0.156,0.167 10 false 1 3.375,5.146 3.531,5.313 0.156,0.167 10 false 1 3.573,2.385 3.729,2.552 0.156,0.167 10 false 1 3.583,2.844 3.74,3.01 0.156,0.167 10 false 2

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR System)>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR System)>INITIALIZATION).


HINT:
·

The following troubleshooting process is based on the premise that the engine can crank normally. If the engine does not crank, proceed to the problem symptoms table.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR System)>PROBLEM SYMPTOMS TABLE

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.

Powertrain > Engine and ECT > Data List
Tester Display
Starter Signal
50003 61 193

d.

Check the value displayed on the GTS when the ignition switch is turned to the ON or START position.

OK:
Ignition Switch Condition GTS Display (Starter Signal)
ON OFF
START ON



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT IGNITION SWITCH ASSEMBLY
2.INSPECT IGNITION SWITCH ASSEMBLY
a.
A222467C07
0.177,0.177 0.427,0.417 0.25,0.24 10 false *a
*a Component without harness connected
(Ignition Switch)


Disconnect the ignition switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
4 - 3 LOCK 10 kΩ or higher
4 - 3 START Below 1 Ω



Result:
Proceed to
OK
NG



NG

3.REPLACE IGNITION SWITCH ASSEMBLY

OK

5.REPAIR OR REPLACE HARNESS AND CONNECTOR (IGNITION SWITCH - ECM)
3.REPLACE IGNITION SWITCH ASSEMBLY
a.

Replace the ignition switch assembly.

Click hereEngine / Hybrid System>1VD-FTV (STARTING)>IGNITION SWITCH>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.READ VALUE USING GTS (STARTER SIGNAL)
4.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.

Powertrain > Engine and ECT > Data List
Tester Display
Starter Signal
50003 61 193

d.

Check the value displayed on the GTS when the ignition switch is turned to the ON or START position.

OK:
Ignition Switch Condition GTS Display (Starter Signal)
ON OFF
START ON



Result:
Proceed to
OK
NG



NG

5.REPAIR OR REPLACE HARNESS AND CONNECTOR (IGNITION SWITCH - ECM)

OK

END

5.REPAIR OR REPLACE HARNESS AND CONNECTOR (IGNITION SWITCH - ECM)
a.

Disconnect the ignition switch connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L21-3 (ST1) - I84-48 (STA) Always Below 1 Ω
L21-3 (ST1) or I84-48 (STA) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK WHETHER DTC OUTPUT RECURS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on and start the engine.


d.

Clear DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 61

e.

Drive the vehicle at more than 20 km/h (12.4 mph) for over 20 seconds.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 61

g.

Read DTCs.

Result:
Proceed to Proceed to
P0617 is output A
No DTC is output B




A

B

END