Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for LHD with VSC) › 2019.09–2022.09
RM25T0E _57 Power Source / Network _057931 NETWORKING _0306321 CAN COMMUNICATION SYSTEM(for LHD with VSC) U

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD with VSC)  TERMINALS OF ECU  


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:
·

Before measuring the resistance, leave the vehicle for at least 1 minute and do not operate the ignition switch, any switches or any doors. If doors need to be opened in order to check connectors, open the doors and leave them open.

·

After turning the cable disconnected from negative (-) battery terminal, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.





CAN JUNCTION CONNECTOR


a.

No. 6 CAN JUNCTION CONNECTOR

HINT:

Connectors that connect to the No. 6 CAN junction connector can be distinguished by color of their CAN bus lines. When the connectors have been disconnected from the No. 6 CAN junction connector, reconnecting the connectors to non-original positions on the No. 6 CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.


C371325C03
5.26,2.813 5.5,2.5 5.5,2.5 5.667,2.5 true 5.271,2.99 5.594,3.26 5.594,3.26 5.76,3.26 true 4.198,2.219 4.51,2.417 0.313,0.198 10 false *a 0.094,0.052 0.406,0.25 0.313,0.198 10 false *1 2.031,2.198 2.344,2.396 0.313,0.198 10 false I119 2.042,2.417 2.354,2.615 0.313,0.198 10 false I120 2.031,3.313 2.344,3.51 0.313,0.198 10 false I124 2.042,3.094 2.448,3.313 0.406,0.219 10 false I123 2.052,2.875 2.427,3.073 0.375,0.198 10 false I122 2.031,2.646 2.417,2.854 0.385,0.208 10 false I121 5.708,2.417 6.292,2.635 0.583,0.219 10 false CANH 5.802,3.188 6.385,3.406 0.583,0.219 10 false CANL
*1 No. 6 CAN Junction Connector - -
*a Rear view of wire harness connector
(to No. 6 CAN Junction Connector)
- -


No. 6 CAN Junction Connector Wiring Color Connect to
I119-1 (CANH) G Combination meter assembly
I119-2 (CANL) W
I120-1 (CANH) L DLC3
I120-2 (CANL) W
I121-1 (CANH) R Spiral with sensor cable sub-assembly (steering angle sensor)
I121-2 (CANL) W
I122-1 (CANH) G ECM
I122-2 (CANL) W
I123-1 (CANH) P Airbag sensor assembly
I123-2 (CANL) W
I124-1 (CANH) B Brake actuator assembly (skid control ECU)
I124-2 (CANL) W



CHECK DLC3


a.
C253362C36
0.167,1 0.583,1.25 0.417,0.25 1.948,0.906 2.167,0.417 2.167,0.417 2.417,0.417 true 1.583,0.906 1.25,0.5 1.25,0.5 1,0.5 true 1.927,1.49 1.667,1.917 1.667,1.917 1.417,1.917 true 2.333,1.5 2.5,1.833 2.5,1.833 2.75,1.833 true 0.25,1.031 0.708,1.229 0.458,0.198 10 false I17 0.75,0.417 1.208,0.615 0.458,0.198 10 false CG 2.469,0.344 2.927,0.542 0.458,0.198 10 false CANH 1.031,1.844 1.49,2.042 0.458,0.198 10 false CANL 2.802,1.76 3.26,1.958 0.458,0.198 10 false BAT 0.094,0.063 0.406,0.219 0.313,0.156 10 false *a
*a Front view of DLC3


Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:
·

After turning the cable disconnected from negative (-) battery terminal, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.




b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I17-6 (CANH) - I17-14 (CANL) L - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
I17-6 (CANH) - I17-4 (CG) L - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
I17-14 (CANL) - I17-4 (CG) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
I17-6 (CANH) - I17-16 (BAT) L - V HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I17-14 (CANL) - I17-16 (BAT) W - V LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)


Refer to Terminals of ECU for Vehicle Stability Control System for further details.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TERMINALS OF ECU

a.
C364734C01
0.573,0.208 1.063,0.427 0.49,0.219 2.094,1.052 2.552,0.458 2.552,0.458 2.719,0.458 true 2.042,1.167 1.813,0.188 1.813,0.188 1.979,0.188 true 2.573,1.344 2.677,1.958 2.677,1.958 2.844,1.958 true 0.51,1.938 0.698,1.938 0.698,1.938 0.854,1.344 true 0.125,0.094 0.438,0.25 0.313,0.156 10 false *a 0.677,0.229 0.99,0.385 0.313,0.156 10 false A42 2.781,0.354 3.281,0.594 0.5,0.24 10 false CANL 2.031,0.104 2.531,0.344 0.5,0.24 10 false CANH 2.906,1.885 3.302,2.146 0.396,0.26 10 false +BS 0.073,1.833 0.469,2.094 0.396,0.26 10 false GND1
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])


Disconnect the brake actuator assembly (skid control ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A42-22 (CANH) - A42-10 (CANL) B - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
A42-22 (CANH) - A42-25 (GND1) B - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A42-10 (CANL) - A42-25 (GND1) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A42-22 (CANH) - A42-38 (+BS) B - R HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A42-10 (CANL) - A42-38 (+BS) W - R LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK ECM


Refer to Terminals of ECU for SFI System (for 1GR-FE) or ECD System (for 1VD-FTV) for further details.

for 1VD-FTV: Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>TERMINALS OF ECM

for 1VD-FTV (w/o EGR System): Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR System)>TERMINALS OF ECM

for 1GR-FE: Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>TERMINALS OF ECM

a.

Disconnect the ECM connectors.

C234869C16
1.99,0.458 2.458,0.729 0.469,0.271 4.594,0.5 5.063,0.771 0.469,0.271 5.813,2.313 5.51,2.313 5.51,2.313 5.208,1.646 true 1.115,1.01 1.333,1.01 1.333,1.01 1.865,1.385 true 2.333,2.333 2.5,2.333 2.5,2.333 2.781,1.729 true 3.385,2.292 3.083,2.292 3.083,2.292 2.781,1.625 true 2.135,0.51 2.427,0.688 0.292,0.177 10 false I84 0.125,0.073 0.417,0.25 0.292,0.177 10 false *a 5.875,2.198 6.74,2.365 0.865,0.167 10 false E1 4.708,0.552 5.042,0.729 0.333,0.177 10 false C39 0.76,0.917 1.188,1.083 0.427,0.167 10 false BATT 1.948,2.26 2.375,2.427 0.427,0.167 10 false CANL 3.458,2.219 3.885,2.385 0.427,0.167 10 false CANH
*a Front view of wire harness connector
(to ECM)
- -



b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I84-41 (CANH) - I84-49 (CANL) G - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 108 to 132 Ω
I84-41 (CANH) - C39-81 (E1) G - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
I84-49 (CANL) - C39-81 (E1) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
I84-41 (CANH) - I84-20 (BATT) G - R-B HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I84-49 (CANL) - I84-20 (BATT) W - R-B LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK COMBINATION METER ASSEMBLY


Refer to Terminals of ECU for Meter / Gauge System for further details.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>TERMINALS OF ECU

a.
C363467C01
1.406,0.25 2.073,0.531 0.667,0.281 1.448,2.365 2.115,2.646 0.667,0.281 0.323,2.104 0.51,2.104 0.51,2.104 0.667,1.667 true 2.938,2.063 2.76,2.063 2.76,2.063 2.531,1.656 true 0.479,4.146 0.667,4.146 0.667,4.146 0.823,3.708 true 0.729,4.396 0.917,4.396 0.917,4.396 1.01,3.74 true 0.198,0.188 0.51,0.344 0.313,0.156 10 false *a 0.073,4.042 0.604,4.417 0.531,0.375 10 false CANH 0.313,4.271 1,4.563 0.688,0.292 10 false CANL 1.563,0.271 2.031,0.51 0.469,0.24 10 false L25 1.625,2.396 2.094,2.635 0.469,0.24 10 false L26 0.104,2 0.635,2.375 0.531,0.375 10 false ES 3.01,1.958 3.427,2.198 0.417,0.24 10 false B
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L26-13 (CANH) - L26-14 (CANL) G - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 108 to 132 Ω
L26-13 (CANH) - L25-15 (ES) G - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
L26-14 (CANL) - L25-15 (ES) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
L26-13 (CANH) - L25-26 (B) G - R HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
L26-14 (CANL) - L25-26 (B) W - R LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK AIRBAG SENSOR ASSEMBLY


Refer to Terminals of ECU for Airbag System for further details.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>TERMINALS OF ECU

a.
C227529C10
0.375,2.521 0.771,2.781 0.396,0.26 0.365,0.948 0.76,1.208 0.396,0.26 2.198,2.896 2.333,3.115 2.333,3.115 2.552,3.115 true 2.115,1.323 2.313,1.677 2.313,1.677 2.552,1.677 true 2.021,1.01 2.438,0.656 2.438,0.656 2.688,0.656 true 1.208,1.677 1.438,1.677 1.438,1.677 1.76,1.323 true 0.177,0.073 0.427,0.271 0.25,0.198 10 false *a 0.198,2.083 0.51,2.24 0.313,0.156 10 false *b 0.49,2.552 0.833,2.76 0.344,0.208 10 false I17 0.458,0.979 0.802,1.188 0.344,0.208 10 false I51 2.75,0.583 3.292,0.792 0.542,0.208 10 false CANH 2.604,1.604 3.146,1.813 0.542,0.208 10 false CANL 2.604,3.042 3.146,3.25 0.542,0.208 10 false BAT 1,1.604 1.542,1.813 0.542,0.208 10 false E1
*a Rear view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of DLC3


Disconnect the airbag sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I51-13 (CANH) - I51-22 (CANL) P - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
I51-13 (CANH) - I51-25 (E1) P - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
I51-22 (CANL) - I51-25 (E1) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
I51-13 (CANH) - I17-16 (BAT) P - V HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I51-22 (CANL) - I17-16 (BAT) W - V LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY (STEERING ANGLE SENSOR)


C201866E09
2.719,1.01 3.26,1.25 0.542,0.24 1.969,1.188 1.635,0.594 1.635,0.594 1.563,0.594 true 2.354,1.188 2.688,0.823 2.688,0.823 2.76,0.823 true 2.25,1.198 2.583,0.5 2.583,0.5 2.656,0.5 true 2.156,1.177 2.323,0.26 2.323,0.26 2.396,0.26 true 2.698,0.396 3.198,0.625 0.5,0.229 10 false CANL 1.24,0.479 1.552,0.646 0.313,0.167 10 false BAT 2.854,1.042 3.167,1.208 0.313,0.167 10 false L47 2.802,0.719 3.302,0.948 0.5,0.229 10 false ESS 2.448,0.156 2.896,0.323 0.448,0.167 10 false CANH

a.
C198943C16
0.656,1.323 1.26,1.573 0.604,0.25 2.125,1.542 2.375,1.115 2.375,1.115 2.458,1.115 true 2.24,1.552 2.615,1.385 2.615,1.385 2.698,1.385 true 2.042,1.552 1.719,1.083 1.719,1.083 1.646,1.083 true 1.802,1.625 1.552,1.906 1.552,1.906 1.385,1.906 true 1.229,0.979 1.646,1.177 0.417,0.198 10 false CANH 0.833,1.344 1.115,1.521 0.281,0.177 10 false L47 0.167,0.052 0.594,0.25 0.427,0.198 10 false *a 2.521,0.979 2.938,1.177 0.417,0.198 10 false CANL 2.771,1.271 3.188,1.469 0.417,0.198 10 false ESS 1.052,1.781 1.469,1.979 0.417,0.198 10 false BAT
*a Rear view of wire harness connector
(to Spiral with Sensor Cable Sub-assembly [Steering Angle Sensor])


Disconnect the spiral with sensor cable sub-assembly (steering angle sensor) connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L47-4 (CANH) - L47-3 (CANL) P - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
L47-4 (CANH) - L47-2 (ESS) P - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
L47-3 (CANL) - L47-2 (ESS) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
L47-4 (CANH) - L47-6 (BAT) P - B HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
L47-3 (CANL) - L47-6 (BAT) W - B LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher