If the key ID codes of the key and transponder key ECU assembly match, the immobiliser system is unset and the engine start permission signal is sent to the ECM. When the ID codes of the transponder key ECU assembly and ECM match, the engine starts.
If the transponder key ECU assembly or ECM is replaced, refer to the Service Bulletin.
Clear the DTCs.
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM>DTC CHECK / CLEAR
DTC is not output.
| Result | Proceed to |
|---|---|
| DTCs are not output (for Gasoline) | A |
| DTCs are not output (for Diesel) | B |
| DTCs are output | C |
A
B
C
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Immobiliser Fuel Cut | Status of immobiliser system fuel cut | ON or OFF | - | - |
| Tester Display |
|---|
| Immobiliser Fuel Cut |
OFF is displayed after the engine is started.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Using a registered key, turn the ignition switch to ON.
Check that the engine starts 5 seconds after the ignition switch was turned to ON.
Engine starts normally.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Using an oscilloscope, check the waveform.
| *a | Component with harness connected (Transponder Key ECU Assembly) |
*b | Waveform A |
| Item | Content |
|---|---|
| Tester Connection | L30-13 (EFIO) - Body ground |
| Tool Setting | 2 V/DIV., 500 ms./DIV. |
| Condition | Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal |
Waveform is output normally (refer to illustration).
| Result | Proceed to |
|---|---|
| Normal waveform | A |
| Waveform A not output, or has abnormal wavelength or shape | B |
A
B
Using an oscilloscope, check the waveform.
| *a | Component with harness connected (Transponder Key ECU Assembly) |
*b | Waveform B |
| *c | Approximately 160 ms | *d | Approximately 510 ms |
| Item | Content |
|---|---|
| Tester Connection | L30-12 (EFII) - Body ground |
| Tool Setting | 2 V/DIV., 500 ms./DIV. |
| Condition | Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal |
Waveform is output normally (refer to illustration).
| Result | Proceed to |
|---|---|
| Normal waveform | A |
| Waveform B not output, or has abnormal wavelength or shape (for 1GR-FE) | B |
| Waveform B not output, or has abnormal wavelength or shape (for 1VD-FTV) | C |
A
B
C
Using an oscilloscope, check the waveform.
| *a | Component with harness connected (Transponder Key ECU Assembly) |
*b | Waveform C |
| *c | Approximately 160 ms | *d | Approximately 510 ms |
| Item | Content |
|---|---|
| Tester Connection | L30-13 (EFIO) - Body ground |
| Tool Setting | 2 V/DIV., 500 ms./DIV. |
| Condition | Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal |
Waveform is output normally (refer to illustration).
| Result | Proceed to |
|---|---|
| Normal waveform | A |
| Waveform C not output, or has abnormal wavelength or shape | B |
A
B
Register the communication ID between the transponder key ECU assembly and ECM.
Refer to the Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Using a registered key, turn the ignition switch to ON.
Check that the engine starts 5 seconds after the ignition switch was turned to ON.
Engine starts normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the transponder key ECU assembly with a new one.
Refer to the Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Register the key.
Refer to the Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Register the ECU communication ID.
Refer to the Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Using a registered key, turn the ignition switch to ON.
Check that the engine starts 5 seconds after the ignition switch was turned to ON.
Engine starts normally.
| Proceed to |
|---|
| OK |
| NG (for 1GR-FE) |
| NG (for 1VD-FTV) |
| NG (for 1VD-FTV (w/ DPF)) |
| NG (for 1VD-FTV (w/o EGR System)) |
OK
NG (for 1GR-FE)
Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
NG (for 1VD-FTV)
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
NG (for 1VD-FTV (w/ DPF))
NG (for 1VD-FTV (w/o EGR System))
Disconnect the L30 transponder key ECU assembly connector.
Disconnect the A29*1, I84*2 ECM connector.
*1: for RHD
*2: for LHD
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L30-12 (EFII) - A29-10 (IMO) | Always | Below 1 Ω |
| L30-13 (EFIO) - A29-11 (IMI) | Always | Below 1 Ω |
| A29-10 (IMO) - Body ground | Always | 10 kΩ or higher |
| L30-12 (EFII) - Body ground | Always | 10 kΩ or higher |
| A29-11 (IMI) - Body ground | Always | 10 kΩ or higher |
| L30-13 (EFIO) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L30-12 (EFII) - I84-10 (IMO) | Always | Below 1 Ω |
| L30-13 (EFIO) - I84-11 (IMI) | Always | Below 1 Ω |
| I84-10 (IMO) - Body ground | Always | 10 kΩ or higher |
| L30-12 (EFII) - Body ground | Always | 10 kΩ or higher |
| I84-11 (IMI) - Body ground | Always | 10 kΩ or higher |
| L30-13 (EFIO) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG