Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM › from 2021.07
RM25T0E _58 Vehicle Interior _029931 SEAT BELT _0138409 SEAT BELT WARNING SYSTEM D

SEAT BELT  SEAT BELT WARNING SYSTEM  OPERATION CHECK  


INSPECT DRIVER SEAT BELT WARNING LIGHT


HINT:

The seat belt warning light on the combination meter assembly is used for both the driver seat and front passenger seat.


a.

w/ Buzzer Regulated by Law

i.

Turn the ignition switch off.


ii.

Turn the ignition switch to ON.


iii.

When the driver seat belt is not fastened, check that the seat belt warning light on the combination meter assembly blinks for 6 seconds.

Check that the seat belt warning light on the combination meter assembly changes from blinking to turns off.


iv.

Lift up the vehicle using a swing arm type lift.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>VEHICLE LIFT AND SUPPORT LOCATIONS


v.

Start the engine.


vi.

Check the status of the seat belt warning light (in the combination meter assembly) under the conditions below.


vii.

Check that the seat belt warning light (in the combination meter assembly) blinks when the driver seat belt is unfastened, the shift position is not in P and the parking brake is released.


viii.

Check that the seat belt warning light (in the combination meter assembly) blinks when the vehicle is driven at approximately 20 km/h (12 mph) or higher with the driver seat belt unfastened.

Check that after 96 seconds, the seat belt warning light (in the combination meter assembly) changes from blinking to on.


ix.

Check that the seat belt warning light (in the combination meter assembly) changes to on when the seat belt warning light (in the combination meter assembly) is blinking, the vehicle speed is 1.75 km/h (1 mph) or less and the shift position is changed to P.


x.

Check that the seat belt warning light (in the combination meter assembly) changes to on when the seat belt warning light (in the combination meter assembly) is blinking, the vehicle speed is 1.75 km/h (1 mph) or less and the parking brake is not released.


xi.

Check that the seat belt warning light (in the combination meter assembly) turns off when the driver seat belt is fastened with the seat belt warning light (in the combination meter assembly) on or blinking.



b.

w/o Buzzer Regulated by Law

i.

Turn the ignition switch to ON.


ii.

Check that the seat belt warning light (in the combination meter assembly) turns on with the driver seat belt unfastened and under the following conditions.

1.

Shift position in P.

2.

The parking brake is not released.



iii.

Lift up the vehicle using a swing arm type lift.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>VEHICLE LIFT AND SUPPORT LOCATIONS


iv.

Start the engine.


v.

Check the status of the seat belt warning light (in the combination meter assembly) under the conditions below.


vi.

Check that the seat belt warning light (in the combination meter assembly) blinks when the driver seat belt is unfastened, the shift position is not in P and the parking brake is released.


vii.

Check that the seat belt warning light (in the combination meter assembly) blinks when the vehicle is driven at approximately 20 km/h (12 mph) or higher with the driver seat belt unfastened.

Check that after 124 seconds, the seat belt warning light (in the combination meter assembly) changes from blinking to on.


viii.

Check that the seat belt warning light (in the combination meter assembly) changes to on when the seat belt warning light (in the combination meter assembly) is blinking, the vehicle speed is 1.75 km/h (1 mph) or less and the shift position is changed to P.


ix.

Check that the seat belt warning light (in the combination meter assembly) changes to on when the seat belt warning light (in the combination meter assembly) is blinking, the vehicle speed is 1.75 km/h (1 mph) or less and the parking brake is not released.


x.

Check that the seat belt warning light (in the combination meter assembly) turns off when the driver seat belt is fastened with the seat belt warning light (in the combination meter assembly) on or blinking.




INSPECT PASSENGER SEAT BELT WARNING LIGHT (w/ Front Passenger Side Seat Belt Warning System)


HINT:

The seat belt warning light on the combination meter assembly is used for both the driver seat and front passenger seat.


a.

Turn the ignition switch to ON.


b.

Check that the seat belt warning light (in the combination meter assembly) turns on with a passenger seated in the passenger seat, the passenger seat belt unfastened and under the following conditions.

1.

Change the shift position to P.

2.

The parking brake is not released.



c.

Fasten the driver seat belt.


d.

Lift up the vehicle using a swing arm type lift.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>VEHICLE LIFT AND SUPPORT LOCATIONS


e.

Start the engine.


f.

Place a load of 20 kg (44.1 lb) on the passenger seat.

NOTICE:

Place the weight on the seat cushion and do not allow it to come into contact with the seatback.



g.

Check the status of the seat belt warning light (in the combination meter assembly) under the conditions below.


h.

Check that the seat belt warning light (in the combination meter assembly) blinks when the passenger seat belt is unfastened, the shift position is not in P and the parking brake is released.


i.

Check that the seat belt warning light (in the combination meter assembly) blinks when the vehicle is driven at approximately 20 km/h (12 mph) or higher with the passenger seat belt unfastened.

Check that after 124 seconds, the seat belt warning light (in the combination meter assembly) changes from blinking to on.


j.

Check that the seat belt warning light (in the combination meter assembly) changes to on when the seat belt warning light (in the combination meter assembly) is blinking, the vehicle speed is 1.75 km/h (1 mph) or less and the shift position is changed to P.


k.

Check that the seat belt warning light (in the combination meter assembly) changes to on when the seat belt warning light (in the combination meter assembly) is blinking, the vehicle speed is 1.75 km/h (1 mph) or less and the parking brake is not released.


l.

Check that the seat belt warning light (in the combination meter assembly) turns off when the passenger seat belt is fastened with the seat belt warning light (in the combination meter assembly) on or blinking.



INSPECT DRIVER SEAT BELT WARNING BUZZER


HINT:

The seat belt warning buzzer can be customized. Make sure that this function is ON.

Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM>CUSTOMIZE PARAMETERS


a.

w/ Buzzer Regulated by Law:

i.

Turn the ignition switch off.


ii.

Turn the ignition switch to ON.


iii.

After turning the ignition switch to ON, wait for approximately 1.8 seconds with the driver seat belt not fastened check that the seat belt warning buzzer in the combination meter assembly sounds at an interval of 1.2 seconds for 6 seconds.


iv.

Lift up the vehicle using a swing arm type lift.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>VEHICLE LIFT AND SUPPORT LOCATIONS


v.

Start the engine.


vi.

Check that the seat belt warning buzzer (in the combination meter assembly) sounds once when the vehicle is driven at approximately 20 km/h (12 mph) or higher with the seat belt unfastened.


vii.

After 24 seconds have passed after the buzzer sounds once, check that the seat belt warning buzzer (in the combination meter assembly) sounds intermittently at 1.2-second intervals for 6 seconds.


viii.

After the buzzer has sounded intermittently at 1.2-second intervals for 6 seconds, check that the interval changes and the buzzer sounds intermittently at 0.4-second intervals for 90 seconds.


ix.

When 96 seconds have passed after the buzzer started sounding intermittently, check that the seat belt warning buzzer (in the combination meter assembly) stops.


x.

After the seat belt warning buzzer (in the combination meter assembly) stops, check that the buzzer once again sounds intermittently when the seat belt is fastened and then unfastened again, and then the vehicle is driven at approximately 20 km/h (12 mph) or higher.


xi.

Check that the seat belt warning buzzer (in the combination meter assembly) stops when the shift position is changed to R while the seat belt warning buzzer (in the combination meter assembly) is sounding.

Check that the buzzer once again sounds intermittently when the shift position is changed to D again and the vehicle is driven at approximately 20 km/h (12 mph) or higher with the seat belt unfastened.



b.

w/o Buzzer Regulated by Law

i.

Lift up the vehicle using a swing arm type lift.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>VEHICLE LIFT AND SUPPORT LOCATIONS


ii.

Start the engine.


iii.

Check that the seat belt warning buzzer (in the combination meter assembly) sounds intermittently at 1.2-second intervals for 24 seconds when the vehicle is driven at approximately 20 km/h (12 mph) or higher with the seat belt unfastened.


iv.

After the buzzer has sounded intermittently at 1.2-second intervals for 24 seconds, check that the interval changes and the buzzer sounds intermittently at 0.4-second intervals for 100 seconds.


v.

When 124 seconds have passed after the buzzer started sounding intermittently, check that the seat belt warning buzzer (in the combination meter assembly) stops.


vi.

Check that the seat belt warning buzzer (in the combination meter assembly) stops when the shift position is changed to R while the seat belt warning buzzer (in the combination meter assembly) is sounding.

Check that the buzzer once again sounds intermittently when the shift position is changed to D again and the vehicle is driven at approximately 20 km/h (12 mph) or higher with the seat belt unfastened.




INSPECT PASSENGER SEAT BELT WARNING BUZZER (w/ Front Passenger Side Seat Belt Warning System)


HINT:

The seat belt warning buzzer can be customized. Make sure that this function is ON.

Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM>CUSTOMIZE PARAMETERS


a.

Lift up the vehicle using a swing arm type lift.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>VEHICLE LIFT AND SUPPORT LOCATIONS


b.

Fasten the driver seat belt.


c.

Start the engine.


d.

Place a load of 20 kg (44.1 lb) on the passenger seat.

NOTICE:

When placing the load on the passenger seat, do not let it touch the seatback.



e.

Check that the seat belt warning buzzer (in the combination meter assembly) sounds intermittently at 1.2-second intervals for 24 seconds when the vehicle is driven at approximately 20 km/h (12 mph) or higher with the seat belt unfastened.


f.

After the buzzer has sounded intermittently at 1.2-second intervals for 24 seconds, check that the interval changes and the buzzer sounds intermittently at 0.4-second intervals for 100 seconds.


g.

When 124 seconds have passed after the buzzer started sounding intermittently, check that the seat belt warning buzzer (in the combination meter assembly) stops.


h.

After the seat belt warning buzzer (in the combination meter assembly) stops, check that the buzzer once again sounds intermittently when the seat belt is fastened and then unfastened again, and then the vehicle is driven at approximately 20 km/h (12 mph) or higher.


i.

Check that the seat belt warning buzzer (in the combination meter assembly) stops when the shift position is changed to R while the seat belt warning buzzer (in the combination meter assembly) is sounding.

Check that the buzzer once again sounds intermittently when the shift position is changed to D again and the vehicle is driven at approximately 20 km/h (12 mph) or higher with the seat belt unfastened.