Home › Vehicle Interior › PRE-COLLISION › PRE-COLLISION SYSTEM › from 2022.09
RM25T0E _58 Vehicle Interior _128087 PRE-COLLISION _0548646 PRE-COLLISION SYSTEM Y

PRE-COLLISION  PRE-COLLISION SYSTEM  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:
·

Use these procedures to troubleshoot the pre-collision system.

·

*: Use the GTS.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.CUSTOMER PROBLEM ANALYSIS AND SYMPTOM CHECK
2.CUSTOMER PROBLEM ANALYSIS AND SYMPTOM CHECK
a.

Interview the customer and confirm the problem.


Result:
Proceed to
NEXT



NEXT

3.PRE-CHECK
3.PRE-CHECK
a.

Measure the battery voltage.

Standard Voltage:

11 to 14 V


HINT:

If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.



b.

Check the fuses and relays.


c.

Check the connector connections and terminals to make sure that there are no abnormalities such as loose connections, deformation, etc.


Result:
Proceed to
NEXT



NEXT

4.CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*
4.CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*

Result:
Result Proceed to
CAN DTCs are not output A
CAN DTCs are output B



A

5.CHECK WARNING LIGHT

B

5.CHECK WARNING LIGHT
a.

Check the condition of warning lights.


Result:
Result Proceed to
PCS warning light is illuminated A
PCS warning light is not illuminated B
PCS warning light and other warning lights are illuminated or blinking C



A

6.CHECK FOR DTCs*

B

14.PROBLEM SYMPTOMS TABLE

C

GO TO OTHER MALFUNCTIONING SYSTEM

6.CHECK FOR DTCs*
a.

Check for DTCs.

Body Electrical > Pre-Collision System > Trouble Codes
50001 432

Result:
Result Proceed to
DTCs are not output A
DTC (C142571) is output B
A DTC other than (C142571) is output C



A

7.CHECK VEHICLE CONTROL HISTORY (RoB)*

B

C

12.CHECK FOR DTCs*
7.CHECK VEHICLE CONTROL HISTORY (RoB)*
a.

Using the GTS, check for Vehicle Control History (RoB).

Body Electrical > Pre-Collision System > Utility
Tester Display
Vehicle Control History (RoB)
50005 432 55

b.

If the Vehicle Control History (RoB) is output, record it.


Result:
Result Proceed to
Vehicle control history (RoB) is not output A
Vehicle control history (RoB) (X2013, X2015, X2022, X2025, X2026 or X2028) is output B
Vehicle control history (RoB) other than (X2013, X2015, X2022, X2025, X2026 and X2028) is output C



A

8.PROBLEM SYMPTOMS TABLE

B

C

13.RECHECK VEHICLE CONTROL HISTORY (RoB)*
8.PROBLEM SYMPTOMS TABLE

Result:
Result Proceed to
Fault is not listed in Problem Symptoms Table. A
Fault is listed in Problem Symptoms Table. B



A

9.OVERALL ANALYSIS AND TROUBLESHOOTING*

B

9.OVERALL ANALYSIS AND TROUBLESHOOTING*


Result:
Proceed to
NEXT



NEXT

10.ADJUST, REPAIR OR REPLACE
10.ADJUST, REPAIR OR REPLACE
Result:
Proceed to
NEXT



NEXT

11.CONFIRMATION TEST
11.CONFIRMATION TEST
Result:
Proceed to
NEXT



NEXT

END

12.CHECK FOR DTCs*
a.

Using the GTS, clear the DTCs.

Body Electrical > Pre-Collision System > Clear DTCs
50002 432

b.

Reproduce the vehicle conditions that were present when the DTCs that were noted were stored.

HINT:

Refer to each corresponding DTC for details on the detection conditions.



c.

Using the GTS, check if the DTCs are output again.

Body Electrical > Pre-Collision System > Trouble Codes
50001 432

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

B

13.RECHECK VEHICLE CONTROL HISTORY (RoB)*
a.

Using the GTS, clear the Vehicle Control History (RoB).

Body Electrical > Pre-Collision System > Utility
Tester Display
Vehicle Control History (RoB)
50005 432 55

b.

Using the GTS, check for Vehicle Control History (RoB).

Body Electrical > Pre-Collision System > Utility
Tester Display
Vehicle Control History (RoB)
50005 432 55

Result:
Result Proceed to
Vehicle Control History (RoB) is not output A
Vehicle Control History (RoB) is output B



A

B

14.PROBLEM SYMPTOMS TABLE

Result:
Result Proceed to
Problem symtoms are not listed in the Problem Symptoms Table A
Problem symtoms are listed in the Problem Symptoms Table B



A

15.CHECK FOR DTCs*

B

15.CHECK FOR DTCs*
a.

Check for DTCs.

Body Electrical > Pre-Collision System > Trouble Codes
50001 432

Result:
Result Proceed to
DTCs are output A
DTCs are not output B



A

16.CHECK CONFIRMED DTC DETECTION CONDITION*

B

17.CHECK VEHICLE CONTROL HISTORY*
16.CHECK CONFIRMED DTC DETECTION CONDITION*
a.

Check detection condition for the confirmed pre-collision system DTC.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>FAIL-SAFE CHART


Result:
Proceed to
NEXT



NEXT

END

Explain to the customer the cause of the previously stored DTC and that the output reason has been cleared.


17.CHECK VEHICLE CONTROL HISTORY*
a.

Check for vehicle control history and note any codes that are output.

Body Electrical > Pre-Collision System > Utility
Tester Display
Vehicle Control History (RoB)
50005 432 55
i.

Record the vehicle control history.



Result:
Result Proceed to
Vehicle control history is not output A
Vehicle control history is output B



A

18.CONDITIONS WHEN PRE-COLLISION SYSTEM OPERATE OR NOT OPERATE

B

20.CHECK VEHICLE CONTROL HISTORY* (PRE-COLLISION SYSTEM)
18.CONDITIONS WHEN PRE-COLLISION SYSTEM OPERATE OR NOT OPERATE
a.

Check the conditions when pre-collision system operates or does not operate.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>PRECAUTION


Result:
Result Proceed to
No condition is met A
Any condition is met B



A

19.INSPECT MILLIMETER WAVE RADAR SENSOR ASSEMBLY* (FRONT BEAM AXIS MISALIGNMENT READING)

B

END (OPERATION/NO OPERATION CONDITIONS OF PRE-COLLISION SYSTEM IS MET)

19.INSPECT MILLIMETER WAVE RADAR SENSOR ASSEMBLY* (FRONT BEAM AXIS MISALIGNMENT READING)
NOTICE:

Before performing beam axis adjustment, check the fitting of the front bumper cover and radiator grille assembly and confirm that there is no warping or deformation.




c.

Turn the cruise control main switch on.


d.

Check the amount of misalignment and make a note.

Body Electrical > Front Radar Sensor > Utility
Tester Display
Front Beam Axis Misalignment Reading
50005 429 4405
Standard (before performing adjustment):
Front beam axis misalignment value:
Vertical -5.0 to 5.0 deg.
Horizontal -0.6 to 0.6 deg.



Result:
Result Proceed to
Front beam axis misalignment value is within the specified range A
Front beam axis misalignment value is not within the specified range B



A

B

20.CHECK VEHICLE CONTROL HISTORY* (PRE-COLLISION SYSTEM)
a.

Check for vehicle control history and note any codes that are output.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>VEHICLE CONTROL HISTORY (RoB)

HINT:

Based on the customer's inquiry, check the corresponding factors in the vehicle control history, such as the detection time and date, trip information and elapsed time.



Result:
Proceed to
NEXT



NEXT

END
a.

Explain to the customer the cause of the previously stored vehicle control history and that the output reason has been cleared.

NOTICE:

After the explanation, make sure to clear vehicle control history.


Body Electrical > Pre-Collision System > Utility
Tester Display
Vehicle Control History (RoB)
50005 432 55