Home › Vehicle Interior › PRE-COLLISION › PRE-COLLISION SYSTEM › from 2022.09
RM25T0E _58 Vehicle Interior _128087 PRE-COLLISION _0548646 PRE-COLLISION SYSTEM T

PRE-COLLISION  PRE-COLLISION SYSTEM  PROBLEM SYMPTOMS TABLE  


NOTICE:

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.


HINT:
·

Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of probability in the "Suspected Area" column of the table. Check each symptom by checking the suspected areas in the order they are listed. Replace parts as necessary.

·

Inspect the fuses and relays related to this system before inspecting the suspected areas below.



Symptom Suspected Area Link
PCS warning light in the combination meter assembly turns on Check the diagnostic code (Pre-collision System) Click here
Check the vehicle control history (RoB) (Pre-collision System) Click here
Vehicle Control History (RoB) (Pre-collision System)
·

X2025: Front Radar Sensor Temporary Unavailable (Horizontal Direction Optical Axis Misalignment)


1.

Check the vehicle control history (RoB) of the pre-collision system.

Click here

2.

If the vehicle control history (RoB) has been stored of the pre-collision system, check the installation status of the millimeter wave radar sensor assembly.

Click here

3.

Millimeter wave radar sensor assembly adjustment

HINT:

Beam axis alignment of the millimeter wave radar sensor assembly can be performed using either Triangle Target, Flat Surface Target or Driving Adjustment.

Triangle Target:Click here

Flat Surface Target:Click here

Driving Adjustment:Click here



Cause:

A determination was made that millimeter wave radar sensor assembly horizontal axis was misaligned.


Vehicle Control History (RoB) (Front Radar Sensor System)
·

X2026: Front Radar Sensor Dirt


1.

Check the vehicle control history (RoB) of the front radar sensor system.

Click here

2.

Confirm that the following condition is met:

There is no foreign matter such as dirt on or around the millimeter wave radar sensor assembly.

-

A cover other than the dedicated radar sensor cover is not installed

-

There is no dirt on the radar sensor cover or millimeter wave radar sensor assembly

-

An accessory, such as a bull bar, a grille guard, etc., which interferes with millimeter radio waves is installed

-

There is no sticker or coating applied to the dedicated radar sensor cover

-

There is no foreign matter between the radar sensor cover and millimeter wave radar sensor assembly



Cause:

The millimeter wave radar sensor assembly is dirty or obstructed by foreign matter.


Vehicle Control History (RoB) (Front Radar Sensor System)
·

X2027: Front Radar Sensor Outside Guaranteed Operating Temperature


1.

Check the vehicle control history (RoB) of the front radar sensor system.

Click here

2.

Using the GTS, check "Millimeter-wave Circuit Temperature Protection" in the Data List for Front Radar Sensor.

Click here

3.

If the value of "Millimeter-wave Circuit Temperature Protection" is ON, warm or cool the area around the millimeter wave radar sensor assembly.


Cause:

The following millimeter wave radar sensor assembly conditions are met:

-

After being subjected to an extremely cold environment, the area around the millimeter wave radar sensor assembly is -30°C (-22°F) or less.

-

After being subjected to an extremely hot environment, the area around the millimeter wave radar sensor assembly is 70°C (158°F) or more.



Vehicle Control History (RoB) (Front Radar Sensor System)
·

X2028: Front Radar Sensor Outside Guaranteed Operating Voltage


1.

Check the vehicle control history (RoB) of the front radar sensor system.

Click here

2.

If this Vehicle Control History (RoB) code is output, clear the Vehicle Control History (RoB), drive the vehicle at 5 km/h (3 mph) or more and then check if this Vehicle Control History (RoB) code is output again.

3.

If output again, check if the voltage between terminals IGB and SGND of the millimeter wave radar sensor assembly is within the specified range.

Click here

4.

Using the GTS, check "IG Voltage Protection" in the Data List for Front Radar Sensor.

Click here

5.

If the value of "IG Voltage Protection" is ON, check if the voltage between terminals IGB and SGND of the millimeter wave radar sensor assembly is within the specified range.

Click here


Cause:

The following millimeter wave radar sensor assembly conditions are met:

-

The input voltage decreases to approximately 8 V or less directly after the engine is started.

-

The input voltage increases to approximately 16 V or more directly after the engine is started.



Check if VSC is not set to OFF -
Vehicle stability control system (w/ Pre-collision System) Click here
DTC is not output, but pre-collision system does not operate at all Pre-collision system may be off -
Front camera system Click here
Front radar sensor system Click here
Check if VSC is not set to OFF -
Vehicle stability control system (w/ Pre-collision System) Click here
Pre-collision system cannot be switched off (PCS warning light does not turn on) Combination meter assembly (check if the indicator turns on using Active Test) Click here
Combination switch assembly (pre-collision system switch) Click here
Harness or connector -
Combination meter assembly Click here
Sensitivity of pre-collision system cannot be adjusted Combination switch assembly (pre-collision system switch) Click here
Harness or connector -
Forward recognition camera Click here
Combination meter assembly Click here