Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SPIRAL CABLE › from 2022.09
RM25T0E _58 Vehicle Interior _029929 SUPPLEMENTAL RESTRAINT SYSTEMS _0137999 SPIRAL CABLE A

SUPPLEMENTAL RESTRAINT SYSTEMS  SPIRAL CABLE  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 84306 1.INSPECT SPIRAL CABLE SUB-ASSEMBLY

a.
B496124C01
1.635,2 2.052,2.438 0.417,0.438 1,2.302 1.417,1.885 true 1.385,1.75 0.969,1.177 true 0.813,2.292 1.125,2.448 0.313,0.156 10 false *a 1.646,2.01 1.833,2.177 0.188,0.167 10 true *b 0.813,1.063 1.125,1.219 0.313,0.156 10 false *c
*a Check Window
*b Matchmark
*c Top of Flat Cable U-turn


Check that the spiral cable sub-assembly is center position.

OK:

The connector is at the top.

The matchmarks are aligned.

The top of the flat cable U-turn can be checked from the check window.



b.

If the spiral cable sub-assembly is not centered, center it.

NOTICE:

Failure to observe the following precautions may result in damage to the spiral cable sub-assembly.

·

Do not turn the spiral cable sub-assembly using the airbag wire harness.

·

Do not forcibly rotate the part.



i.
B459529C01
0,0 0,0 false
V100135

Counterclockwise


Make sure to rotate the spiral cable sub-assembly counterclockwise slowly by hand until it stops.

NOTICE:

Make sure to rotate the spiral cable sub-assembly counterclockwise. If rotated clockwise, it may be damaged or centering may no longer be possible.



ii.
B459530

If the spiral cable sub-assembly stops rotating and the connector has moved past the bottom, return the connector to the bottom as shown in the illustration.


iii.
B459531C01
0,0 0,0 false
V100135

Clockwise


Rotate the spiral cable sub-assembly clockwise approximately 2.5 times to move the connector from the bottom to the top.

NOTICE:

If the connector is rotated clockwise from the bottom 5 times or more, the spiral cable sub-assembly may be damaged.



iv.
B496124C01
1.635,2 2.052,2.438 0.417,0.438 1,2.302 1.417,1.885 true 1.385,1.75 0.969,1.177 true 0.813,2.292 1.125,2.448 0.313,0.156 10 false *a 1.646,2.01 1.833,2.177 0.188,0.167 10 true *b 0.813,1.063 1.125,1.219 0.313,0.156 10 false *c
*a Check Window
*b Matchmark
*c Top of Flat Cable U-turn


Check that the spiral cable sub-assembly is center position.

OK:

The connector is at the top.

The matchmarks are aligned.

The top of the flat cable U-turn can be checked from the check window.


NOTICE:

If the spiral cable sub-assembly cannot be centered, it is possible that the spiral cable sub-assembly is broken. Replace the spiral cable sub-assembly with a new one.




Hide 84306 2.INSTALL SPIRAL CABLE SUB-ASSEMBLY

NOTICE:
B263617C02
0,0 0,0 false
V100135

Lock Pin


When replacing the spiral cable sub-assembly with a new one, remove the lock pin before installing the steering wheel assembly.


a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the front wheels are facing straight ahead.


d.

Set the turn signal switch to the neutral position.

NOTICE:

If it is not in the neutral position, the turn signal switch cancel ratchet may snap.



e.
B374337C01
0.844,4.313 0.844,4.49 0.844,4.49 0.563,4.49 true 0.375,4.396 0.688,4.552 0.313,0.156 10 false *1
*1 Slider


Attach the 3 claws to install the spiral cable sub-assembly.


f.

Connect the connectors to the spiral cable sub-assembly.

NOTICE:

When handling the airbag connector, do not damage the airbag wire harness.



Hide 45286B 3.INSTALL UPPER STEERING COLUMN COVER

Hide 45287 4.INSTALL LOWER STEERING COLUMN COVER

Hide 84306 5.ADJUST SPIRAL CABLE SUB-ASSEMBLY

a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.
B496276C01
1.469,1.479 1.813,1.802 0.344,0.323 1.167,3.198 0.813,2.74 true 0.708,2.448 0.323,1.802 true 1.229,3.135 1.542,3.292 0.313,0.156 10 false *a 0.156,1.677 0.469,1.833 0.313,0.156 10 false *c 1.479,1.49 1.677,1.667 0.198,0.177 10 true *b
*a Check Window
*b Matchmark
*c Top of Flat Cable U-turn


Check that the spiral cable sub-assembly is center position.

OK:

The connector is at the top.

The matchmarks are aligned.

The top of the flat cable U-turn can be checked from the check window.



d.

If the spiral cable sub-assembly is not centered, center it.

NOTICE:

Failure to observe the following precautions may result in damage to the spiral cable sub-assembly.

·

Do not turn the spiral cable sub-assembly using the airbag wire harness.

·

Do not forcibly rotate the part.



i.
B459533C01
0,0 0,0 false
V100135

Counterclockwise


Make sure to rotate the spiral cable sub-assembly counterclockwise slowly by hand until it stops.

NOTICE:

Make sure to rotate the spiral cable sub-assembly counterclockwise. If rotated clockwise, it may be damaged or centering may no longer be possible.



ii.
B459534

If the spiral cable sub-assembly stops rotating and the connector has moved past the bottom, return the connector to the bottom as shown in the illustration.


iii.
B459535C01
0,0 0,0 false
V100135

Clockwise


Rotate the spiral cable sub-assembly clockwise approximately 2.5 times to move the connector from the bottom to the top.

NOTICE:

If the connector is rotated clockwise from the bottom 5 times or more, the spiral cable sub-assembly may be damaged.



iv.
B496276C01
1.469,1.479 1.813,1.802 0.344,0.323 1.167,3.198 0.813,2.74 true 0.708,2.448 0.323,1.802 true 1.229,3.135 1.542,3.292 0.313,0.156 10 false *a 0.156,1.677 0.469,1.833 0.313,0.156 10 false *c 1.479,1.49 1.677,1.667 0.198,0.177 10 true *b
*a Check Window
*b Matchmark
*c Top of Flat Cable U-turn


Check that the spiral cable sub-assembly is center position.

OK:

The connector is at the top.

The matchmarks are aligned.

The top of the flat cable U-turn can be checked from the check window.


NOTICE:

If the spiral cable sub-assembly cannot be centered, it is possible that the spiral cable sub-assembly is broken. Replace the spiral cable sub-assembly with a new one.




Hide 55480D 6.INSTALL LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY

Hide 45100 7.INSTALL STEERING WHEEL ASSEMBLY

Hide 8.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Hide 9. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART