Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SIDE AIRBAG SENSOR › from 2022.09
RM25T0E _58 Vehicle Interior _029929 SUPPLEMENTAL RESTRAINT SYSTEMS _0285169 SIDE AIRBAG SENSOR A

SUPPLEMENTAL RESTRAINT SYSTEMS  SIDE AIRBAG SENSOR  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 89865 1.INSTALL DOOR SIDE AIRBAG SENSOR LH

a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Attach the guide and hold the door side airbag sensor LH in place.


d.

Install the bolt.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)

NOTICE:
·

If the door side airbag sensor LH has been dropped, replace it with a new one.

·

When installing the door side airbag sensor LH, be careful that the SRS wiring does not interfere with or is not pinched between other parts.

·

Tighten the bolt while holding the door side airbag sensor LH because the door side airbag sensor LH guide is easily damaged.




e.

Connect the airbag connector.

NOTICE:

When connecting any airbag connector, take care not to damage the airbag wire harness.


i.

Before connecting the airbag connector, check that the position of the housing lock is correct as shown in the illustration.

B340848C02
4.583,0.594 4.896,0.75 0.313,0.156 10 *a 4.677,1.875 4.99,2.031 0.313,0.156 10 *b 1.385,0.615 1.698,0.771 0.313,0.156 10 *a 1.448,1.865 1.76,2.021 0.313,0.156 10 *b
*a Incorrect *b Correct



ii.

While holding the CPA, be sure to engage the connectors until they are locked and check that the CPA is in its original position (when locking, make sure that a click sound can be heard).

HINT:

When engaged, the white housing lock will slide. Be sure not to hold the white housing lock and upper part of the CPA, as it may result in an insecure fit.


B340850C07
2.271,1.198 2.5,1.76 2.5,1.76 2.729,1.76 false 2.438,1.01 2.844,0.521 2.844,0.521 3.115,0.521 true 1.521,1.125 1.792,1.125 1.792,1.125 2.083,0.917 true 3.167,0.417 3.479,0.573 0.313,0.156 10 false *a 2.781,1.656 3.094,1.813 0.313,0.156 10 false *b 5.823,2.073 6.135,2.229 0.313,0.156 10 false *d 1.365,1.021 1.823,1.219 0.458,0.198 10 false *c
*a Housing Lock *b CPA
*c CPA Upper Part *d Connection is Completed




f.

Check that there is no looseness in the installation parts of the door side airbag sensor LH.


Hide 62316C 3.CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH

Hide 5.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Hide 6. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART