Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM (w/ Pre-collision System) › from 2022.09
RM25T0E _54 Brake _029873 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0548732 VEHICLE STABILITY CONTROL SYSTEM(w/ Pre-collision System) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(w/ Pre-collision System)  C050023  Left Front Wheel Speed Sensor Signal Stuck Low  C050623  Right Front Wheel Speed Sensor Signal Stuck Low  


DESCRIPTION

Refer to DTCs C05001F and C05061F.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/ Pre-collision System)>C05001F

DTC No. Detection Item DTC Detection Condition Trouble Area
C050023 Left Front Wheel Speed Sensor Signal Stuck Low Either of the following is detected:
1.

When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 10 km/h (6 mph) or more, output voltage from one of the speed sensors is less than that from the other sensors for 15 seconds or more.

2.

When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 10 km/h (6 mph) or more, output from one of the speed sensors is 0 km/h (0 mph) for 1 second or more.

3.

When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 10 km/h (6 mph) or more, outputs from both front speed sensors are 0 km/h (0 mph) for 30 seconds or more.


·

Front speed sensor LH

·

Front skid control rotor LH (Front axle hub sub-assembly LH)

·

Sensor installation


C050623 Right Front Wheel Speed Sensor Signal Stuck Low Either of the following is detected:
1.

When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 10 km/h (6 mph) or more, output voltage from one of the speed sensors is less than that from the other sensors for 15 seconds or more.

2.

When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 10 km/h (6 mph) or more, output from one of the speed sensors is 0 km/h (0 mph) for 1 second or more.

3.

When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 10 km/h (6 mph) or more, outputs from both front speed sensors are 0 km/h (0 mph) for 30 seconds or more.


·

Front speed sensor RH

·

Front skid control rotor RH (Front axle hub sub-assembly RH)

·

Sensor installation



C050023 DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3
Diagnosis Condition When the +BS terminal voltage is 17.4 V or less ○ ○ ○
Malfunction Status At a vehicle speed of 10 km/h (6 mph) or more, output voltage from one of the speed sensors is less than that from the other sensors ○ - -
At a vehicle speed of 10 km/h (6 mph) or more, output from one of the speed sensors is 0 km/h (0 mph) - ○ -
At a vehicle speed of 10 km/h (6 mph) or more, outputs from both front speed sensors are 0 km/h (0 mph) - - ○
Detection Time 15 seconds or more. 1 second or more. 30 seconds or more.
Number of Trips 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


C050623 DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3
Diagnosis Condition When the +BS terminal voltage is 17.4 V or less ○ ○ ○
Malfunction Status At a vehicle speed of 10 km/h (6 mph) or more, output voltage from one of the speed sensors is less than that from the other sensors ○ - -
At a vehicle speed of 10 km/h (6 mph) or more, output from one of the speed sensors is 0 km/h (0 mph) - ○ -
At a vehicle speed of 10 km/h (6 mph) or more, outputs from both front speed sensors are 0 km/h (0 mph) - - ○
Detection Time 15 seconds or more. 1 second or more. 30 seconds or more.
Number of Trips 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


PROCEDURE

1.CHECK FRONT SPEED SENSOR INSTALLATION
a.

Turn the ignition switch off.


b.
C168336C14
1.994,1.633 2.181,1.795 0.186,0.161 10 *c 0.685,0.198 0.871,0.359 0.186,0.161 10 *a 2.296,0.198 2.482,0.359 0.186,0.161 10 *b
*a Normal
*b Abnormal
*c Clearance


Check the speed sensor installation.

OK:

There is no clearance between the sensor and the steering knuckle.

The installation bolt is tightened properly.



Result:
Proceed to
OK
NG



OK

2.INSPECT FRONT SPEED SENSOR TIP

NG

2.INSPECT FRONT SPEED SENSOR TIP

b.

Check the speed sensor tip.

OK:

No scratches, oil, or foreign matter on the sensor tip.


NOTICE:
·

If no damage to the speed sensor tip is found during this inspection, do not replace the speed sensor.

·

If there is iron powder sticking to the rotor, this will result in a malfunction, so confirm that the rotor is not contaminated with foreign material before replacing the sensor.




Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (FRONT SPEED SENSOR)

NG

CLEAN OR REPLACE FRONT SPEED SENSOR

3.READ VALUE USING GTS (FRONT SPEED SENSOR)
a.

According to the display on the GTS, read the Data List.

Chassis > Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Wheel Speed Front wheel speed sensor RH reading Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
FL Wheel Speed Front wheel speed sensor LH reading Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
Chassis > Brake > Data List
Tester Display
FR Wheel Speed
FL Wheel Speed
50003 435 13,14

b.

Check that there is no difference between the speed value output from the speed sensor displayed on the GTS and the speed value displayed on the speedometer when driving the vehicle.

HINT:

Factors that affect the indicated vehicle speed include tire size, tire inflation and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>OPERATION CHECK


OK:

The speed value output from the speed sensor displayed on the GTS is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).


HINT:

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/ Pre-collision System)>PROBLEM SYMPTOMS TABLE


Result:
Proceed to
OK
NG




OK

NG

4.INSPECT SKID CONTROL SENSOR WIRE
4.INSPECT SKID CONTROL SENSOR WIRE
C494104C01
0.917,0.385 1.333,0.604 0.417,0.219 2.385,0.354 2.802,0.656 0.417,0.302 4.385,0.146 4.802,0.365 0.417,0.219 4.396,0.438 4.813,0.656 0.417,0.219 5.802,0.094 6.219,0.396 0.417,0.302 5.813,0.448 6.229,0.75 0.417,0.302 2.406,1.271 1.719,2.094 true 2.76,1.281 3.313,2.104 true 5.802,1.24 5.219,1.875 true 6.271,1.271 6.635,1.917 true 0.135,0.094 0.448,0.292 0.313,0.198 10 false *1 1.073,0.406 1.229,0.604 0.156,0.198 10 false A 2.51,0.427 2.823,0.625 0.313,0.198 10 false B3 2.906,0.313 3.219,0.51 0.313,0.198 10 false *A 2.906,0.552 3.219,0.75 0.313,0.198 10 false *C 1.385,0.313 1.698,0.51 0.313,0.198 10 false *A 4.531,0.156 4.688,0.354 0.156,0.198 10 false A 4.875,0.146 5.188,0.344 0.313,0.198 10 false *A 4.896,0.5 5.208,0.698 0.313,0.198 10 false *B 4.542,0.458 4.698,0.656 0.156,0.198 10 false B 5.917,0.156 6.229,0.354 0.313,0.198 10 false B4 6.302,0.135 6.615,0.333 0.313,0.198 10 false *A 6.521,0.135 6.833,0.333 0.313,0.198 10 false *D 5.906,0.521 6.365,0.719 0.458,0.198 10 false A21 6.323,0.521 6.635,0.719 0.313,0.198 10 false *B 1.031,1.75 1.344,1.948 0.313,0.198 10 false *a 4.552,1.729 4.865,1.927 0.313,0.198 10 false *a 2.49,2.51 2.802,2.708 0.313,0.198 10 false *b 5.948,2.021 6.26,2.219 0.313,0.198 10 false *b 1.573,2.167 2.031,2.365 0.458,0.198 10 false FR+ 3.229,2.177 3.688,2.375 0.458,0.198 10 false FR- 5,1.979 5.635,2.135 0.635,0.156 10 false FR+ (*A) 5,2.198 5.708,2.427 0.708,0.229 10 false FL+ (*B) 6.458,1.99 7.052,2.219 0.594,0.229 10 false FR- (*A) 6.458,2.219 7.052,2.448 0.594,0.229 10 false FL- (*B)
*A for RH *B for LH
*C except Pick-Up Body Type *D Pick-Up Body Type
*1 Skid Control Sensor Wire - -
*a Speed Sensor Side *b Wire Harness Side


a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.

Disconnect the A or B skid control sensor wire connector (speed sensor side).


d.

Disconnect the B3*1, B4*2 or A21 skid control sensor wire connector (wire harness side).

*1: except Pick-Up Body Type

*2: Pick-Up Body Type



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH (except Pick-Up Body Type)
Tester Connection Condition Specified Condition
B3-2 (FR+) - A-3 Always Below 1 Ω
B3-1 (FR-) - A-1 Always Below 1 Ω
B3-2 (FR+) or A-3 - Body ground Always 10 kΩ or higher
B3-1 (FR-) or A-1 - Body ground Always 10 kΩ or higher

for RH (Pick-Up Body Type)
Tester Connection Condition Specified Condition
B4-3 (FR+) - A-3 Always Below 1 Ω
B4-1 (FR-) - A-1 Always Below 1 Ω
B4-3 (FR+) or A-3 - Body ground Always 10 kΩ or higher
B4-1 (FR-) or A-1 - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
A21-3 (FL+) - B-3 Always Below 1 Ω
A21-1 (FL-) - B-1 Always Below 1 Ω
A21-3 (FL+) or B-3 - Body ground Always 10 kΩ or higher
A21-1 (FL-) or B-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - SKID CONTROL SENSOR WIRE)

NG

REPLACE SKID CONTROL SENSOR WIRE

5.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - SKID CONTROL SENSOR WIRE)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.

Disconnect the A45 skid control ECU (brake actuator assembly) connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH (except Pick-Up Body Type)
Tester Connection Condition Specified Condition
A45-7 (FR+) - B3-2 (FR+) Always Below 1 Ω
A45-6 (FR-) - B3-1 (FR-) Always Below 1 Ω
A45-7 (FR+) or B3-2 (FR+) - Body ground Always 10 kΩ or higher
A45-6 (FR-) or B3-1 (FR-) - Body ground Always 10 kΩ or higher

for RH (Pick-Up Body Type)
Tester Connection Condition Specified Condition
A45-7 (FR+) - B4-3 (FR+) Always Below 1 Ω
A45-6 (FR-) - B4-1 (FR-) Always Below 1 Ω
A45-7 (FR+) or B4-3 (FR+) - Body ground Always 10 kΩ or higher
A45-6 (FR-) or B4-1 (FR-) - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
A45-22 (FL+) - A21-3 (FL+) Always Below 1 Ω
A45-21 (FL-) - A21-1 (FL-) Always Below 1 Ω
A45-22 (FL+) or A21-3 (FL+) - Body ground Always 10 kΩ or higher
A45-21 (FL-) or A21-1 (FL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT FRONT AXLE HUB SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT FRONT AXLE HUB SUB-ASSEMBLY
a.

Remove the component with the front axle hub sub-assembly.

Click hereDrivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB>REMOVAL


b.

Check the front skid control rotor.

OK:

No scratches, oil, or foreign matter on the rotors.


NOTICE:

Check the speed sensor signal after cleaning or replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/ Pre-collision System)>TEST MODE PROCEDURE


HINT:
·

The front skid control rotor is incorporated into the front axle hub sub-assembly.

·

If the skid control rotor needs to be replaced, replace it together with the front axle hub sub-assembly.




c.

Reinstall the front speed sensor and the component with the front axle hub sub-assembly.

for the front speed sensor: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR (w/ VSC)>INSTALLATION

for the front axle hub sub-assembly: Click hereDrivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB>INSTALLATION


Result:
Result Proceed to
OK A
NG (The front skid control rotor is damaged.) B
NG (There is foreign matter on the front skid control rotor.) C



A

B

REPLACE FRONT AXLE HUB SUB-ASSEMBLY

C

CLEAN FRONT SKID CONTROL ROTOR