Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM (w/ Pre-collision System) › from 2022.09
RM25T0E _54 Brake _029873 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0548732 VEHICLE STABILITY CONTROL SYSTEM(w/ Pre-collision System) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(w/ Pre-collision System)  C050C1F  Left Rear Wheel Speed Sensor Circuit Intermittent  C05121F  Right Rear Wheel Speed Sensor Circuit Intermittent  


DESCRIPTION

The speed sensor detects wheel speed and sends the appropriate signals to the skid control ECU (brake actuator assembly). These signals are used for brake control.

Skid control rotors have rows of alternating N and S magnetic poles, and their magnetic fields change when the rotors turn.

Each speed sensor detects that magnetic change and sends a pulse signal to the skid control ECU (brake actuator assembly).

DTC No. Detection Item DTC Detection Condition Trouble Area
C050C1F Left Rear Wheel Speed Sensor Circuit Intermittent Either of the following is detected:
1.

When the +BS terminal voltage is 17.4 V or less, an open in the sensor signal circuit of a malfunctioning area occurs 255 times or more.

2.

When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 20 km/h (12 mph) or more, noise occurs in the sensor signals of a malfunctioning wheel 75 times or more within 5 seconds.

3.

When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 10 km/h (6 mph) or more, noise occurs once per rotor rotation for 15 seconds or more.


·

Rear speed sensor LH

·

Rear skid control rotor LH (Rear axle hub and bearing assembly LH)

·

Sensor installation

·

Wire harness or connector


C05121F Right Rear Wheel Speed Sensor Circuit Intermittent Either of the following is detected:
1.

When the +BS terminal voltage is 17.4 V or less, an open in the sensor signal circuit of a malfunctioning area occurs 255 times or more.

2.

When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 20 km/h (12 mph) or more, noise occurs in the sensor signals of a malfunctioning wheel 75 times or more within 5 seconds.

3.

When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 10 km/h (6 mph) or more, noise occurs once per rotor rotation for 15 seconds or more.


·

Rear speed sensor RH

·

Rear skid control rotor RH (Rear axle hub and bearing assembly RH)

·

Sensor installation

·

Wire harness or connector



C050C1F DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3
Diagnosis Condition When the +BS terminal voltage is 17.4 V or less ○ ○ ○
Malfunction Status An open in the sensor signal circuit of a malfunctioning area occurs 255 times or more ○ - -
At a vehicle speed of 20 km/h (12 mph) or more, noise occurs in the sensor signals of a malfunctioning wheel 75 times or more within 5 seconds - ○ -
At a vehicle speed of 10 km/h (6 mph) or more, noise occurs once per rotor rotation - - ○
Detection Time - - 15 seconds or more.
Number of Trips 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


C05121F DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3
Diagnosis Condition When the +BS terminal voltage is 17.4 V or less ○ ○ ○
Malfunction Status An open in the sensor signal circuit of a malfunctioning area occurs 255 times or more ○ - -
At a vehicle speed of 20 km/h (12 mph) or more, noise occurs in the sensor signals of a malfunctioning wheel 75 times or more within 5 seconds - ○ -
At a vehicle speed of 10 km/h (6 mph) or more, noise occurs once per rotor rotation - - ○
Detection Time - - 15 seconds or more.
Number of Trips 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


PROCEDURE

1.READ VALUE USING GTS (REAR SPEED SENSOR, MOMENTARY INTERRUPTION)
a.

According to the display on the GTS, display the Data List, perform a driving test based on the conditions when the problem occurred (determined from the freeze frame data or customer problem analysis results) and check the Data List when the vehicle is running and stopped.

Chassis > Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Wheel Speed Rear wheel speed sensor RH reading Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
RL Wheel Speed Rear wheel speed sensor LH reading Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
RR Speed Open Rear speed sensor RH open detection Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
After a momentary interruption occurs, if there is no momentary interruption for 1 second, it switches from "Under intermittent" to "Normal".
RL Speed Open Rear speed sensor LH open detection Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
After a momentary interruption occurs, if there is no momentary interruption for 1 second, it switches from "Under intermittent" to "Normal".
Chassis > Brake > Data List
Tester Display
RR Wheel Speed
RL Wheel Speed
RR Speed Open
RL Speed Open
50003 435 15,16,103,104
OK:

Output value does not change and no interruptions occur according to vehicle speed.


HINT:

Perform the above inspection before removing the sensor and connector.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK REAR SPEED SENSOR INSTALLATION
2.CHECK REAR SPEED SENSOR INSTALLATION
a.

Turn the ignition switch off.


b.
C168336C39
1.994,1.633 2.181,1.795 0.186,0.161 10 *c 0.685,0.198 0.871,0.359 0.186,0.161 10 *a 2.296,0.198 2.482,0.359 0.186,0.161 10 *b
*a Normal
*b Abnormal
*c Clearance


Check the speed sensor installation.

OK:

There is no clearance between the sensor and the rear axle housing.

The installation bolt is tightened properly.



Result:
Proceed to
OK
NG



OK

3.CHECK REAR SPEED SENSOR (CHECK FOR FOREIGN MATTER)

NG

3.CHECK REAR SPEED SENSOR (CHECK FOR FOREIGN MATTER)

b.

Check the rear speed sensor.

OK:

The rear speed sensor tip is free of oil and foreign matter.


HINT:

If foreign matter of 1 mm (0.03937 in.) x 1 mm (0.03937 in.) or more is adhered to the rear speed sensor, this DTC may be stored.



Result:
Proceed to
OK
NG



OK

4.CHECK REAR AXLE HUB AND BEARING ASSEMBLY (CHECK FOR FOREIGN MATTER)

NG

7.CLEAN REAR SPEED SENSOR
4.CHECK REAR AXLE HUB AND BEARING ASSEMBLY (CHECK FOR FOREIGN MATTER)
a.

Remove the component with the rear axle hub and bearing assembly.

Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE HUB>REMOVAL


b.

Check the rear skid control rotor.

OK:

The rear skid control rotor is free of oil and foreign matter.


HINT:

If foreign matter of 1 mm (0.03937 in.) x 1 mm (0.03937 in.) or more is adhered to the rear skid control rotor, this DTC may be stored.



Result:
Proceed to
OK
NG



OK

REPLACE REAR SPEED SENSOR AND REAR AXLE HUB AND BEARING ASSEMBLY

NG

5.CLEAN REAR SKID CONTROL ROTOR
5.CLEAN REAR SKID CONTROL ROTOR
a.

Clean the rear skid control rotor.

NOTICE:

Do not use parts cleaner when cleaning the rear skid control rotor.



Result:
Proceed to
NEXT



NEXT

6.READ VALUE USING GTS (REAR SPEED SENSOR, MOMENTARY INTERRUPTION)
6.READ VALUE USING GTS (REAR SPEED SENSOR, MOMENTARY INTERRUPTION)
a.

According to the display on the GTS, display the Data List, perform a driving test based on the conditions when the problem occurred (determined from the freeze frame data or customer problem analysis results) and check the Data List when the vehicle is running and stopped.

Chassis > Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Wheel Speed Rear wheel speed sensor RH reading Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
RL Wheel Speed Rear wheel speed sensor LH reading Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
RR Speed Open Rear speed sensor RH open detection Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
After a momentary interruption occurs, if there is no momentary interruption for 1 second, it switches from "Under intermittent" to "Normal".
RL Speed Open Rear speed sensor LH open detection Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
After a momentary interruption occurs, if there is no momentary interruption for 1 second, it switches from "Under intermittent" to "Normal".
Chassis > Brake > Data List
Tester Display
RR Wheel Speed
RL Wheel Speed
RR Speed Open
RL Speed Open
50003 435 15,16,103,104
OK:

Output value does not change and no interruptions occur according to vehicle speed.


HINT:

Perform the above inspection before removing the sensor and connector.



Result:
Proceed to
OK
NG



OK

END

NG

REPLACE REAR SPEED SENSOR AND REAR AXLE HUB AND BEARING ASSEMBLY

7.CLEAN REAR SPEED SENSOR
a.

Clean the rear speed sensor.

NOTICE:

When cleaning the rear speed sensor, make sure to clean the installation hole before installation.



Result:
Proceed to
NEXT



NEXT

8.READ VALUE USING GTS (REAR SPEED SENSOR, MOMENTARY INTERRUPTION)
8.READ VALUE USING GTS (REAR SPEED SENSOR, MOMENTARY INTERRUPTION)
a.

According to the display on the GTS, display the Data List, perform a driving test based on the conditions when the problem occurred (determined from the freeze frame data or customer problem analysis results) and check the Data List when the vehicle is running and stopped.

Chassis > Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Wheel Speed Rear wheel speed sensor RH reading Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
RL Wheel Speed Rear wheel speed sensor LH reading Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
RR Speed Open Rear speed sensor RH open detection Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
After a momentary interruption occurs, if there is no momentary interruption for 1 second, it switches from "Under intermittent" to "Normal".
RL Speed Open Rear speed sensor LH open detection Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
After a momentary interruption occurs, if there is no momentary interruption for 1 second, it switches from "Under intermittent" to "Normal".
Chassis > Brake > Data List
Tester Display
RR Wheel Speed
RL Wheel Speed
RR Speed Open
RL Speed Open
50003 435 15,16,103,104
OK:

Output value does not change and no interruptions occur according to vehicle speed.


HINT:

Perform the above inspection before removing the sensor and connector.



Result:
Proceed to
OK
NG



OK

END

NG

4.CHECK REAR AXLE HUB AND BEARING ASSEMBLY (CHECK FOR FOREIGN MATTER)