Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM (w/ Pre-collision System) › from 2022.09
RM25T0E _54 Brake _029873 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0548732 VEHICLE STABILITY CONTROL SYSTEM(w/ Pre-collision System) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(w/ Pre-collision System)  C137BA2  Brake System Control Module "A" System Voltage System Voltage Low  


DESCRIPTION

If a malfunction is detected in the power supply circuit, the skid control ECU (brake actuator assembly) stores this DTC and the fail-safe function prohibits ABS operation.

This DTC is stored when the +BS terminal voltage deviates from the DTC detection condition due to a malfunction in the power supply or charging circuit such as the battery or generator circuit, etc.

The DTC is canceled when the +BS terminal voltage returns to normal.

DTC No. Detection Item DTC Detection Condition Trouble Area
C137BA2 Brake System Control Module "A" System Voltage System Voltage Low Any of the following is detected:
·

When the +BS terminal voltage is below 9.5 V, the power source voltage for all speed sensors is continuously low for 60 seconds or more.

·

After the +BS terminal voltage is below 9.5 V continuously for 3 seconds or more, the +BS terminal voltage is below 9.5 V continuously for 7 seconds or more at a vehicle speed exceeding 3 km/h (2 mph).

·

When the +BS terminal voltage is 9.5 V or higher and the vehicle speed exceeds 15 km/h (9 mph), the IG1 terminal voltage is 10 V or less continuously for 60 seconds or more.

·

When the +BS terminal voltage is below 9.5 V and the solenoid relay is ON, the relay contact is OFF continuously for 1.22 seconds or more.

·

When the +BS terminal voltage is below 9.5 V, motor fail-safe relay overcurrent continues for 1.05 seconds or more.


·

Battery

·

Charging system

·

Wire harness or connector

·

Skid control ECU (Brake actuator assembly)



HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


C137BA2 DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4 Pattern 5
Diagnosis Condition When the +BS terminal voltage is below 9.5 V ○ - - ○ ○
After the +BS terminal voltage is below 9.5 V continuously for 3 seconds or more - ○ - - -
When the +BS terminal voltage is 9.5 V or higher and the vehicle speed exceeds 15 km/h (9 mph) - - ○ - -
Malfunction Status When the power source voltage for all speed sensors is continuously low ○ - - - -
When the +BS terminal voltage is below 9.5 V continuously for 7 seconds or more at a vehicle speed exceeding 3 km/h (2 mph) - ○ - - -
When the IG1 terminal voltage is 10 V or less - - ○ - -
When the solenoid relay is ON, the relay contact is OFF continuously - - - ○ -
When the motor fail-safe relay overcurrent continues - - - - ○
Detection Time 60 seconds or more. - 60 seconds or more. 1.22 seconds or more. 1.05 seconds or more.
Number of Trips 1 trip 1 trip 1 trip 1 trip 1 trip

WIRING DIAGRAM

C416042E19
5.99,1.25 6.448,1.448 0.458,0.198 10 false +BS 5.99,2.865 6.448,3.063 0.458,0.198 10 false GND1 5.667,1.125 5.979,1.323 0.313,0.198 10 false 14 5.677,2.719 5.99,2.917 0.313,0.198 10 false 1 4.063,4.031 7,4.323 2.938,0.292 10 false Skid Control ECU (Brake Actuator Assembly) 4.094,3.771 4.51,3.948 0.417,0.177 10 false A45 3.698,1.458 4.375,1.698 0.677,0.24 10 false ABS SOL 2,1.24 2.99,1.5 0.99,0.26 10 false from Battery 3.75,2.24 4.427,2.479 0.677,0.24 10 false ECU IG 1.865,2.042 3.042,2.354 1.177,0.313 10 false from IG Circuit 5.677,1.917 5.99,2.115 0.313,0.198 10 false 45 6.01,2.031 6.469,2.229 0.458,0.198 10 false IG1

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/ Pre-collision System)>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.INSPECT BATTERY
a.

Check the battery voltage.

Standard voltage:

11 to 14 V


Result:
Proceed to
OK
NG




OK

2.CHECK TERMINAL VOLTAGE (+BS TERMINAL)

NG

2.CHECK TERMINAL VOLTAGE (+BS TERMINAL)
C494113C05
1.542,0.094 2,0.333 0.458,0.24 2.844,0.188 2.76,0.188 2.76,0.188 2.76,0.865 true 2.896,0.094 3.292,0.344 0.396,0.25 10 false +BS 1.635,0.135 1.938,0.344 0.302,0.208 10 false A45 0.073,0.063 0.385,0.26 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


a.

Turn the ignition switch off.


b.

Make sure that there is no looseness in the locking part and connecting part of the connectors.


c.

Disconnect the A45 skid control ECU (brake actuator assembly) connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A45-14 (+BS) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK TERMINAL VOLTAGE (IG1 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (+BS CIRCUIT)

3.CHECK TERMINAL VOLTAGE (IG1 TERMINAL)
a.
C494113C06
1.542,0.094 2,0.333 0.458,0.24 2.521,1.281 2.521,1.792 true 2.469,1.854 2.927,2.083 0.458,0.229 10 false IG1 1.635,0.135 1.938,0.344 0.302,0.208 10 false A45 0.073,0.063 0.385,0.26 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Disconnect the A45 skid control ECU (brake actuator assembly) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A45-45 (IG1) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)

4.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)
a.

Turn the ignition switch off.


b.
C494113C07
1.542,0.094 2,0.333 0.458,0.24 0.521,0.885 0.25,1.823 true 1.635,0.135 1.938,0.344 0.302,0.208 10 false A45 0.073,0.063 0.385,0.26 0.313,0.198 10 false *a 0.104,1.875 0.719,2.073 0.615,0.198 10 false GND1
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A45-1 (GND1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)

5.RECONFIRM DTC
a.

Reconnect the A45 skid control ECU (brake actuator assembly) connector.


b.

Clear the DTCs.

Chassis > Brake > Clear DTCs
50002 435

c.

Turn the ignition switch off.


d.

Start the engine.


e.

Drive the vehicle at a speed of 20 km/h (12 mph) or more for 30 seconds or more.


f.

Check if the same DTC is recorded.

Chassis > Brake > Trouble Codes
50001 435
HINT:

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/ Pre-collision System)>PROBLEM SYMPTOMS TABLE



Result:
Result Proceed to
DTC C137BA2 is not output A
DTC C137BA2 is output B



A

B