Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM (w/ Pre-collision System) › from 2022.09
RM25T0E _54 Brake _029873 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0548732 VEHICLE STABILITY CONTROL SYSTEM(w/ Pre-collision System) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(w/ Pre-collision System)  C137BA3  Brake System Control Module "A" System Voltage System Voltage High  


DESCRIPTION

If a malfunction is detected in the power supply circuit, the skid control ECU (brake actuator assembly) stores this DTC and the fail-safe function prohibits ABS operation.

This DTC is stored when the +BS terminal voltage deviates from the DTC detection condition due to a malfunction in the power supply or charging circuit such as the battery or generator circuit, etc.

The DTC is canceled when the +BS terminal voltage returns to normal.

DTC No. Detection Item DTC Detection Condition Trouble Area
C137BA3 Brake System Control Module "A" System Voltage System Voltage High The +BS terminal voltage is 17.4 V or more for 0.8 seconds or more.
·

Charging system

·

Skid control ECU (Brake actuator assembly)

·

Wire harness or connector

·

Battery



WIRING DIAGRAM

C307645E29
3.708,2.885 4.885,3.135 1.177,0.25 10 false Skid Control ECU 5.313,1.49 6.406,2.021 1.094,0.531 10 false Master Cylinder Pressure Sensor 3.177,0.854 3.635,1.052 0.458,0.198 10 false +BS 2.802,0.865 3.26,1.063 0.458,0.198 10 false 14 1.781,1.167 2.531,1.5 0.75,0.333 10 false ABS SOL 0.417,0.969 1.396,1.333 0.979,0.365 10 false from Battery 3.156,2.146 3.615,2.344 0.458,0.198 10 false GND1 2.833,2.146 3.292,2.344 0.458,0.198 10 false 1 2.896,3.271 3.354,3.469 0.458,0.198 10 false A45 3.375,3.271 5.385,3.542 2.01,0.271 10 false Brake Actuator Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/ Pre-collision System)>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.INSPECT BATTERY
a.

Check the battery voltage.

Standard voltage:

11 to 14 V


Result:
Proceed to
OK
NG




OK

2.CHECK TERMINAL VOLTAGE (+BS TERMINAL)

NG

2.CHECK TERMINAL VOLTAGE (+BS TERMINAL)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.
C494113C03
1.542,0.094 2,0.333 0.458,0.24 2.833,0.208 2.75,0.208 2.75,0.208 2.75,0.865 true 0.229,1.823 0.542,0.896 true 2.906,0.146 3.365,0.375 0.458,0.229 10 false +BS 1.635,0.135 1.938,0.344 0.302,0.208 10 false A45 0.073,0.063 0.385,0.26 0.313,0.198 10 false *a 0.125,1.885 0.74,2.083 0.615,0.198 10 false GND1
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Disconnect the A45 skid control ECU (brake actuator assembly) connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A45-14 (+BS) - Body ground Always 11 to 14 V
A45-14 (+BS) -A45-1 (GND1) Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (+BS CIRCUIT)

3.RECONFIRM DTC
a.

Reconnect the A45 skid control ECU (brake actuator assembly) connector.


b.

Clear the DTCs.

Chassis > Brake > Clear DTCs
50002 435

c.

Turn the ignition switch off.


d.

Start the engine.


e.

Perform a road test.


f.

Check if the same DTC is recorded.

Chassis > Brake > Trouble Codes
50001 435

Result:
Result Proceed to
DTC C137BA3 is not output A
DTC C137BA3 is output B



A

B