Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM (w/ Pre-collision System) › from 2022.09
RM25T0E _54 Brake _029873 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0548732 VEHICLE STABILITY CONTROL SYSTEM(w/ Pre-collision System) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(w/ Pre-collision System)  C14D71C  Multi-axis Acceleration Sensor Module "A" Supply Voltage Circuit Voltage Out of Range  


DESCRIPTION

The skid control ECU (brake actuator assembly) receives signals from the yaw rate and acceleration sensor (airbag ECU assembly) via the CAN communication system.

The airbag ECU assembly has a built-in acceleration sensor and detects the vehicle condition.

If there is trouble in the bus lines between the acceleration sensor (airbag ECU assembly) and the CAN communication system, the DTC U012587 is output.

These DTCs are also output when calibration has not been completed.

DTC No. Detection Item DTC Detection Condition Trouble Area
C14D71C Multi-axis Acceleration Sensor Module "A" Supply Voltage Circuit Voltage Out of Range When the +BS terminal voltage is from 9.5 to 17.4 V at a vehicle speed of more than 3 km/h (2 mph), the acceleration sensor power source malfunction signal is received for 10 seconds or more.
·

IGN fuse

·

Acceleration sensor (Airbag ECU assembly)

·

Wire harness or connector



WIRING DIAGRAM

C427101E24
5.188,4.135 7.083,4.656 1.896,0.521 10 false Skid Control ECU (Brake Actuator Assembly) 5.198,3.917 5.604,4.125 0.406,0.208 10 false A45 5.781,1.125 6.188,1.333 0.406,0.208 10 false 27 5.781,0.521 6.188,0.729 0.406,0.208 10 false 43 6.052,1.313 6.51,1.521 0.458,0.208 10 false CANH 6.063,0.698 6.521,0.906 0.458,0.208 10 false CANL 0.802,0.708 1.26,0.917 0.458,0.208 10 false CANL 0.76,1.313 1.219,1.521 0.458,0.208 10 false CANH 0.917,1.938 1.375,2.146 0.458,0.208 10 false IG2 1.292,1.802 1.75,2.01 0.458,0.208 10 false 21 2.365,2.094 3.448,2.323 1.083,0.229 10 false IGN 3.979,1.927 5.156,2.156 1.177,0.229 10 false from IG Circuit 0.969,3.125 1.427,3.333 0.458,0.208 10 false E2 1.292,3.052 1.479,3.26 0.188,0.208 10 false 26 0.271,4.052 0.729,4.26 0.458,0.208 10 false I51 0.271,4.219 2.448,4.625 2.177,0.406 10 false Yaw Rate and Acceleration Sensor (Airbag ECU Assembly) 3.458,3.115 5.198,3.417 1.74,0.302 10 false : CAN Communication Line 1.292,0.49 1.698,0.698 0.406,0.208 10 false 22 1.292,1.125 1.698,1.333 0.406,0.208 10 false 13 1.292,2.417 1.75,2.625 0.458,0.208 10 false 25 0.969,2.531 1.427,2.74 0.458,0.208 10 false E1

CAUTION / NOTICE / HINT

NOTICE:
·

If the yaw rate and acceleration sensor (airbag ECU assembly) was replaced or reinstalled, perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/ Pre-collision System)>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK TERMINAL VOLTAGE (IG2 TERMINAL)
NOTICE:
·

After the power switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting and reconnecting the battery.

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


d.
C233304C45
1.521,0.271 1.969,0.552 0.448,0.281 1.125,1.469 0.563,1.469 false 0.24,1.375 0.49,1.552 0.25,0.177 10 false IG2 0.146,0.073 0.333,0.229 0.188,0.156 10 false *a 1.604,0.333 1.896,0.49 0.292,0.156 10 false I51
*a Front view of wire harness connector
(to Yaw Rate and Acceleration Sensor [Airbag ECU Assembly])


Disconnect the I51 yaw rate and acceleration sensor (airbag ECU assembly) connector.


e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Turn the ignition switch to ON.


g.

Operate all the components of the electrical system (defogger, wipers, headlights, heater blower, etc.).


h.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
I51-21 (IG2) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (GND TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG2 CIRCUIT)

2.CHECK HARNESS AND CONNECTOR (GND TERMINAL)
a.

Turn the ignition switch off.


b.
C233304C46
1.521,0.271 2.01,0.563 0.49,0.292 1.813,1.542 2.125,1.802 false 1.667,1.542 1.375,1.802 false 1.229,1.833 1.427,2.01 0.198,0.177 10 false E1 2.052,1.833 2.25,2.01 0.198,0.177 10 false E2 0.146,0.073 0.333,0.229 0.188,0.156 10 false *a 1.646,0.333 1.938,0.49 0.292,0.156 10 false I51
*a Front view of wire harness connector
(to Yaw Rate and Acceleration Sensor [Airbag ECU Assembly])


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I51-25 (E1) - Body ground Always Below 1 Ω
I51-26 (E2) - Body ground Always Below 1 Ω


HINT:

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/ Pre-collision System)>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)

3.RECONFIRM DTC
a.

Reconnect the I51 yaw rate and acceleration sensor (airbag ECU assembly) connector.


b.

Clear the DTCs.

Chassis > Brake > Clear DTCs
50002 435

c.

Turn the ignition switch off.


d.

Start the engine.


e.

Perform a road test.


f.

Check if the same DTC is recorded.

Chassis > Brake > Trouble Codes
50001 435

Result:
Result Proceed to
DTC C14D71C is not output A
DTC C14D71C is output B



A

B