Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM (w/ Pre-collision System) › from 2022.09
RM25T0E _54 Brake _029873 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0548732 VEHICLE STABILITY CONTROL SYSTEM(w/ Pre-collision System) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(w/ Pre-collision System)  C14FE14  Steering Angle Sensor Supply Voltage Circuit Short to Ground or Open  


DESCRIPTION

The skid control ECU (brake actuator assembly) outputs this DTC when it receives a sensor power source malfunction signal from the steering sensor.

DTC No. Detection Item DTC Detection Condition Trouble Area
C14FE14 Steering Angle Sensor Supply Voltage Circuit Short to Ground or Open Steering sensor power supply malfunction signal is received from steering sensor.
·

Steering sensor (Spiral cable with sensor sub-assembly)

·

Wire harness or connector



WIRING DIAGRAM

C377599E70
0.802,0.635 1.417,0.833 0.615,0.198 10 false CANL 0.781,1.229 1.396,1.427 0.615,0.198 10 false CANH 0.896,1.75 1.51,1.948 0.615,0.198 10 false BAT 0.99,2.438 1.604,2.635 0.615,0.198 10 false IG 0.885,3.313 1.5,3.51 0.615,0.198 10 false ESS 6.031,0.635 6.646,0.833 0.615,0.198 10 false CANL 6.031,1.229 6.646,1.427 0.615,0.198 10 false CANH 3.615,1.729 5.167,2.146 1.552,0.417 10 false from Battery 3.635,2.396 4.792,2.677 1.156,0.281 10 false from IG Circuit 2.25,1.917 3.385,2.167 1.135,0.25 10 false ECU-B 2.24,2.573 3.396,2.823 1.156,0.25 10 false ECU IG 0.292,4.052 0.906,4.25 0.615,0.198 10 false L47 0.292,4.24 3.927,4.458 3.635,0.219 10 false Steering Sensor (Spiral Cable with Sensor Sub-assembly) 5.208,3.875 5.823,4.073 0.615,0.198 10 false A45 5.208,4.073 7.104,4.51 1.896,0.438 10 false Skid Control ECU (Brake Actuator Assembly) 2.979,3.542 4.906,3.792 1.927,0.25 10 false : CAN Communication Line 1.313,3.177 1.5,3.417 0.188,0.24 10 false 2 1.323,2.292 1.51,2.531 0.188,0.24 10 false 5 1.323,1.625 1.51,1.865 0.188,0.24 10 false 6 1.344,1.052 1.531,1.292 0.188,0.24 10 false 4 1.344,0.458 1.531,0.698 0.188,0.24 10 false 3 5.781,0.458 5.969,0.698 0.188,0.24 10 false 43 5.781,1.042 5.969,1.281 0.188,0.24 10 false 27

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the steering sensor, confirm that the replacement part is of the correct specification.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:
·

When U007488, U012587 and/or U012687 is output together with C14FE14, inspect and repair the trouble areas indicated by U007488, U012587 and/or U012687 first.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/ Pre-collision System)>U007488

·

When the speed sensor or the yaw rate sensor (airbag ECU assembly) has trouble, DTCs for the steering sensor may be output even when the steering sensor is normal. When DTCs for the speed sensor or yaw rate sensor (airbag ECU assembly) are output together with DTCs for the steering sensor, inspect and repair the speed sensor and yaw rate sensor (airbag ECU assembly) first, and then inspect and repair the steering sensor.



PROCEDURE

1.CHECK TERMINAL VOLTAGE (BAT TERMINAL)
C364760C04
0.24,1.167 0.615,1.417 0.375,0.25 2.354,1.885 2.354,1.5 false 0.104,0.063 0.417,0.26 0.313,0.198 10 false *a 0.323,1.208 0.708,1.427 0.385,0.219 10 false L47 2.24,1.917 2.594,2.125 0.354,0.208 10 false BAT
*a Front view of wire harness connector
(to Steering Sensor [Spiral Cable with Sensor Sub-assembly])


a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.

Disconnect the L47 steering sensor (spiral cable with sensor sub-assembly) connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L47-6 (BAT) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK TERMINAL VOLTAGE (IG TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BAT CIRCUIT)

2.CHECK TERMINAL VOLTAGE (IG TERMINAL)
C364760C05
0.24,1.167 0.615,1.417 0.375,0.25 2.063,1.885 2.063,1.5 false 0.104,0.063 0.417,0.26 0.313,0.198 10 false *a 0.323,1.208 0.708,1.427 0.385,0.219 10 false L47 2,1.917 2.354,2.125 0.354,0.208 10 false IG
*a Front view of wire harness connector
(to Steering Sensor [Spiral Cable with Sensor Sub-assembly])


a.

Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
L47-5 (IG) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (ESS TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG CIRCUIT)

3.CHECK HARNESS AND CONNECTOR (ESS TERMINAL)
C364760C06
0.24,1.167 0.615,1.417 0.375,0.25 1.354,1.885 1.354,1.5 false 0.104,0.063 0.417,0.26 0.313,0.198 10 false *a 0.323,1.208 0.708,1.427 0.385,0.219 10 false L47 1.208,1.917 1.563,2.125 0.354,0.208 10 false ESS
*a Front view of wire harness connector
(to Steering Sensor)


a.

Turn the ignition switch off.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L47-2 (ESS) - Body ground Always Below 1 Ω


HINT:

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/ Pre-collision System)>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

REPLACE SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ESS CIRCUIT)