Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM (w/ Pre-collision System) › from 2022.09
RM25T0E _54 Brake _029873 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0548732 VEHICLE STABILITY CONTROL SYSTEM(w/ Pre-collision System) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(w/ Pre-collision System)  U007488  Control Module Communication Bus "B" Off Bus Off  U010087  Lost Communication with ECM/PCM "A" Missing Message  U012587  Lost Communication with Multi-axis Acceleration Sensor Module Missing Message  U012687  Lost Communication with Steering Angle Sensor Module Missing Message  


DESCRIPTION

The skid control ECU (brake actuator assembly) receives the signals from the ECM, steering and yaw rate and acceleration sensor (airbag ECU assembly) via the CAN communication system.

DTC No. Detection Item DTC Detection Condition Trouble Area
U007488 Control Module Communication Bus "B" Off Bus Off Either of the following is detected:
1.

A bus OFF state occurs once or more within 0.1 seconds, 10 times in succession. (Sent signals cannot be received.)

2.

When the +BS terminal voltage is between 9.5 and 17.4 V, a delay in receiving data from the yaw rate sensor and steering sensor continues for 1 second or more.

3.

When the +BS terminal voltage is between 9.5 and 17.4 V, the following occurs 10 times in succession within 60 seconds.

-

The condition that a delay in receiving data from the yaw rate sensor and steering sensor occurs more than once within 5 seconds.



CAN communication system
U010087 Lost Communication with ECM/PCM "A" Missing Message When the +BS terminal voltage is between 9.5 and 17.4 V, and the vehicle speed is 15 km/h (9 mph) or more, data cannot be received from the ECM for 2 seconds or more.
·

CAN communication system

·

Skid control ECU (Brake actuator assembly)

·

ECM


U012587 Lost Communication with Multi-axis Acceleration Sensor Module Missing Message Either of the following is detected:
1.

When the +BS terminal voltage is between 9.5 and 17.4 V, and the vehicle speed is 7 km/h or more, data from the acceleration sensor cannot be received for 1 second or more.

2.

When the +BS terminal voltage is between 9.5 and 17.4 V, the following occurs 10 times in succession within 60 seconds.

-

The condition that data from the acceleration sensor cannot be received occurs once or more within 5 seconds.



·

CAN communication system

·

Skid control ECU (Brake actuator assembly)

·

Acceleration sensor (Airbag ECU assembly)


U012687 Lost Communication with Steering Angle Sensor Module Missing Message Either of the following is detected:
1.

When the +BS terminal voltage is between 9.5 and 17.4 V, data from the steering sensor cannot be received for 1 second or more.

2.

When the +BS terminal voltage is between 9.5 and 17.4 V, the following occurs 10 times in succession within 60 seconds.

-

The condition that data from the steering sensor cannot be received occurs once or more within 5 seconds.



·

CAN communication system

·

Skid control ECU (Brake actuator assembly)

·

Steering sensor



U007488 DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3
Diagnosis Condition When the +BS terminal voltage is between 9.5 and 17.4 V - ○ ○
Malfunction Status A bus OFF state occurs once or more (Sent signals cannot be received.) ○ - -
A delay in receiving data from the yaw rate sensor and steering sensor continues - ○ -
The condition that a delay in receiving data from the yaw rate sensor and steering sensor occurs more than once within 5 seconds. - - ○
Detection Time Within 0.1 seconds, 10 times in succession. 1 second or more. Occurs 10 times in succession within 60 seconds.
Number of Trips 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


U012587 DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition When the +BS terminal voltage is between 9.5 and 17.4 V ○ ○
Malfunction Status The vehicle speed is 7 km/h or more, data from the acceleration sensor cannot be received ○ -
The condition that data from the acceleration sensor cannot be received occurs once or more within 5 seconds - ○
Detection Time 1 second or more. Occurs 10 times in succession within 60 seconds.
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


U012687 DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition When the +BS terminal voltage is between 9.5 and 17.4 V ○ ○
Malfunction Status Data from the steering sensor cannot be received ○ -
The condition that data from the steering sensor cannot be received occurs once or more within 5 seconds - ○
Detection Time 1 second or more. Occurs 10 times in succession within 60 seconds.
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
a.

Using the GTS, check for any momentary interruption in the wire harness and connector corresponding to a DTC.

Chassis > Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
EFI Communication Open ECM communication open detection Normal or Error Normal Error: Momentary interruption
Yaw Rate Open Yaw rate sensor open detection Normal or Error Normal Error: Momentary interruption
Deceleration Open Acceleration sensor open detection Error or Normal Normal Error: Momentary interruption
Steering Open Steering sensor open detection Normal or Error Normal Error: Momentary interruption
Chassis > Brake > Data List
Tester Display
EFI Communication Open
Yaw Rate Open
Deceleration Open
Steering Open
50003 435 105,106,107,108
HINT:

Perform the above inspection before removing the sensor and connector.



Result:
Result Proceed to
There is a constant open circuit A
There are no momentary interruptions B
There are momentary interruptions C



A

2.CHECK IF EACH SENSOR AND ECM CONNECTOR IS SECURELY CONNECTED

B

3.RECONFIRM DTC

C

4.REPAIR OR REPLACE HARNESS OR CONNECTOR
2.CHECK IF EACH SENSOR AND ECM CONNECTOR IS SECURELY CONNECTED
a.

Turn the ignition switch off.


b.

Check if each sensor or ECM connector is securely connected.

OK:

Each connector is securely connected.



Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

CONNECT CONNECTOR TO EACH SENSOR OR ECM CORRECTLY

3.RECONFIRM DTC
a.

Turn the ignition switch off.


b.

Record the output DTCs (for VSC system and/or CAN communication system).

for CAN communication system: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Pre-collision System)>DIAGNOSIS SYSTEM

Chassis > Brake > Trouble Codes
50001 435
HINT:

If the CAN communication system DTC and the relevant sensor DTCs are output simultaneously, troubleshoot the relevant sensor DTCs (for VSC system) after the CAN communication system returns to normal.


Result:
Result Proceed to
DTC (relating to CAN communication system) is output A
DTC (relating to VSC system) is output B
DTC is not output C




A

B

REPAIR CIRCUIT INDICATED BY OUTPUT DTC

C

4.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Turn the ignition switch off.


b.

Repair or replace the harness or connector.


c.

Check for any momentary interruption between the skid control ECU (brake actuator assembly) and each sensor or ECM.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/ Pre-collision System)>CHECK FOR INTERMITTENT PROBLEMS


d.

Check that there is no momentary interruption.


Result:
Proceed to
NEXT



NEXT

5.RECONFIRM DTC
5.RECONFIRM DTC
a.

Turn the ignition switch off.


b.

Clear the DTCs.

Chassis > Brake > Clear DTCs
50002 435

c.

Start the engine.


d.

Drive the vehicle at a speed of 15 km/h (9 mph) or more and turn the steering wheel to the right and left.


e.

f.

If VSC system DTCs are output, record them.

Click here

Chassis > Brake > Trouble Codes
50001 435
HINT:

The CAN communication system must be normal when repairing each sensor DTC (for VSC system).



Result:
Result Proceed to
DTC is not output A
DTC is output (relating to VSC system) B
DTC is output (relating to CAN communication system) C



A

END

B

REPAIR CIRCUIT INDICATED BY OUTPUT DTC

C