Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2022.09
RM25T0E _58 Vehicle Interior _029927 METER / GAUGE / DISPLAY _0137559 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Speedometer Malfunction  


DESCRIPTION

w/ VSC


The combination meter assembly receives vehicle speed signals from the brake actuator assembly (skid control ECU) via the CAN communication line. The wheel speed sensors output voltages that vary according to the vehicle speed. The brake actuator assembly (skid control ECU) supplies power to the wheel speed sensors. The brake actuator assembly (skid control ECU) calculates the vehicle speed based on the pulses of the voltage.


w/o VSC


The combination meter assembly receives a vehicle speed signal from the speedometer sensor*1 or brake actuator assembly (skid control ECU)*2.

*1: w/o ABS

*2: w/ ABS



WIRING DIAGRAM

E255800E25
4.656,2.563 6.875,2.813 2.219,0.25 10 false Combination Meter Assembly 1.198,2.552 2.865,2.99 1.667,0.438 10 false Brake Actuator Assembly (Skid Control ECU) 0.802,3.375 3.563,3.656 2.76,0.281 10 false : CAN Communication Line 0.188,0.135 2.948,0.417 2.76,0.281 12 false w/ VSC:

E224935E19
4.74,1.875 6.458,2.083 1.719,0.208 10 false L25 4.729,2.021 6.604,2.323 1.875,0.302 10 false Combination Meter Assembly 5.094,1.063 6.813,1.271 1.719,0.208 10 false SI 4.885,0.948 6.604,1.156 1.719,0.208 10 false 9 2.188,0.958 3.906,1.167 1.719,0.208 10 false 22 1.813,1.063 3.531,1.271 1.719,0.208 10 false SP1 0.979,1.865 2.635,2.167 1.656,0.302 10 false A20 0.979,2.01 2.573,2.344 1.594,0.333 10 false Brake Actuator Assembly (Skid Control ECU) 0.104,0.083 3.156,0.365 3.052,0.281 12 false w/ ABS, w/o VSC:

E295957E02
1.146,2.302 3.896,2.5 2.75,0.198 10 false C96 1.146,2.438 3.896,2.635 2.75,0.198 10 false Speedometer Sensor 4.896,1.854 6.74,2.052 1.844,0.198 10 false L25 4.896,2.031 6.073,2.354 1.177,0.323 10 false Combination Meter Assembly 1.896,1.76 2.417,2.135 0.521,0.375 10 false SE 1.948,1.302 2.469,1.677 0.521,0.375 10 false SI 1.865,0.833 2.385,1.208 0.521,0.375 10 false IG+ 2.198,1.667 2.719,2.042 0.521,0.375 10 false 2 2.198,1.219 2.719,1.594 0.521,0.375 10 false 3 2.188,0.75 2.708,1.125 0.521,0.375 10 false 1 5.083,0.844 5.604,1.219 0.521,0.375 10 false IG+ 5.083,1.292 5.604,1.667 0.521,0.375 10 false SI 4.896,1.208 5.417,1.583 0.521,0.375 10 false 9 4.823,0.75 5.344,1.125 0.521,0.375 10 false 13 0.125,0.104 3.177,0.688 3.052,0.583 12 false w/o ABS:

PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
w/ VSC A
w/ ABS, w/o VSC B
w/o ABS C



A

2.CHECK FOR DTC

B

5.READ VALUE USING GTS (VEHICLE SPEED)

C

9.CHECK COMBINATION METER ASSEMBLY
2.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR

Body Electrical > Combination Meter > Trouble Codes
50001 122
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

3.CHECK FOR DTC (VEHICLE STABILITY CONTROL SYSTEM)

NG

3.CHECK FOR DTC (VEHICLE STABILITY CONTROL SYSTEM)
a.

Check for DTCs.

w/o Pre-collision System:

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/o Pre-collision System)>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

w/ Pre-collision System:

Chassis > Brake > Trouble Codes
50001 435
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

4.PERFORM ACTIVE TEST USING GTS (SPEED METER OPERATION)

NG

4.PERFORM ACTIVE TEST USING GTS (SPEED METER OPERATION)
a.

Using the GTS, perform the Active Test.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Speed Meter Operation Speedometer OFF, 0, 40, 80, 120 or 160 (km/h) There is a deviation in the values displayed on the speedometer display (Control range → Speedometer)
Tire Side: 265/70R16 115R LT
·

40 → 40.8 to 45.3

·

80 → 81.5 to 86.5

·

120 → 122.3 to 127.3

·

160 → 163 to 168


Tire Side: 7.50R16-8PRLT RGF
·

40 → 41.4 to 45.9

·

80 → 82.8 to 87.8

·

120 → 124.1 to 129.1

·

160 → 165.5 to 170.5


Body Electrical > Combination Meter > Active Test
Tester Display
Speed Meter Operation
50004 122 1
OK:

Speedometer indication is normal.



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)

NG

REPLACE COMBINATION METER ASSEMBLY

5.READ VALUE USING GTS (VEHICLE SPEED)
a.

Using the GTS, read the Data List.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Normal Condition Reference Value Diagnostic Note
Vehicle Speed Vehicle speed Min.: 0 mph (0 km/h), Max.: 326.4 km/h (202.8 mph) Almost same as actual vehicle speed measured using a speedometer tester -
Chassis > ABS/VSC/TRC > Data List
Tester Display
Vehicle Speed
50003 105 42
OK:

Vehicle speed displayed on the GTS is almost the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).



Result:
Proceed to
OK
NG



OK

6.CHECK COMBINATION METER ASSEMBLY

NG

6.CHECK COMBINATION METER ASSEMBLY
a.
C227495C04
1.458,0.198 1.885,0.448 0.427,0.25 2.573,1.844 2.385,1.844 2.385,1.844 2.021,1.25 true 0.094,0.083 0.406,0.24 0.313,0.156 10 false *a 1.563,0.24 1.875,0.396 0.313,0.156 10 false A20 2.625,1.74 2.938,1.896 0.313,0.156 10 false SP1
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])


Disconnect the brake actuator assembly (skid control ECU) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A20-22 (SP1) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

7.CHECK COMBINATION METER ASSEMBLY

NG

8.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE ACTUATOR ASSEMBLY [SKID CONTROL ECU])
7.CHECK COMBINATION METER ASSEMBLY
a.
E293690C02
0.208,1.104 0.656,1.344 0.448,0.24 0.646,0.802 0.844,0.802 0.844,0.802 1.396,1.198 true 0.167,0.115 0.479,0.313 0.313,0.198 10 false *a 0.156,2.302 0.469,2.5 0.313,0.198 10 false *b 2.781,3.49 3.094,3.688 0.313,0.198 10 false GND 0.469,0.708 0.781,0.906 0.313,0.198 10 false SI 0.333,1.135 0.646,1.333 0.313,0.198 10 false L25
*a Component with harness connected
(Combination Meter Assembly)
*b Waveform


Remove the combination meter assembly with the connector(s) still connected.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL


b.

Using an oscilloscope, check the signal waveform of the meter.

Measurement Condition
Item Content
Tester Connection L25-9 (SI) - Body ground
Tool Setting 5 V/DIV., 20 msec./DIV.
Condition Driving at approximately 20 km/h (12 mph)

OK:

The waveform displayed is as shown in the illustration.


HINT:

As the vehicle speed increases, the wavelength shortens.



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)

8.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE ACTUATOR ASSEMBLY [SKID CONTROL ECU])
a.

Disconnect the L25 combination meter assembly connector.


b.

Disconnect the A20 brake actuator assembly (skid control ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L25-9 (SI) - A20-22 (SP1) Always Below 1 Ω
L25-9 (SI) or A20-22 (SP1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK COMBINATION METER ASSEMBLY
a.
E293690C02
0.208,1.104 0.656,1.344 0.448,0.24 0.646,0.802 0.844,0.802 0.844,0.802 1.396,1.198 true 0.167,0.115 0.479,0.313 0.313,0.198 10 false *a 0.156,2.302 0.469,2.5 0.313,0.198 10 false *b 2.781,3.49 3.094,3.688 0.313,0.198 10 false GND 0.469,0.708 0.781,0.906 0.313,0.198 10 false SI 0.333,1.135 0.646,1.333 0.313,0.198 10 false L25
*a Component with harness connected
(Combination Meter Assembly)
*b Waveform


Remove the combination meter assembly with the connector(s) still connected.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL


b.

Using an oscilloscope, check the signal waveform of the meter.

Measurement Condition
Item Content
Tester Connection L25-9 (SI) - Body ground
Tool Setting 5 V/DIV., 20 msec./DIV.
Condition Driving at approximately 20 km/h (12 mph)

OK:

The waveform displayed is as shown in the illustration.


HINT:

As the vehicle speed increases, the wavelength shortens.



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

10.CHECK HARNESS AND CONNECTOR (SPEEDOMETER SENSOR - COMBINATION METER ASSEMBLY AND BODY GROUND)
10.CHECK HARNESS AND CONNECTOR (SPEEDOMETER SENSOR - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the C96 speedometer sensor connector.


b.

Disconnect the L25 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C96-1 (IG+) - L25-13 (IG+) Always Below 1 Ω
C96-3 (SI) - L25-9 (SI) Always Below 1 Ω
C96-2 (SE) - Body ground Always Below 1 Ω
C96-1 (IG+) or L25-13 (IG+) - Body ground Always 10 kΩ or higher
C96-3 (SI) or L25-9 (SI) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.CHECK COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK COMBINATION METER ASSEMBLY
a.
E295956C03
0.188,0.885 0.615,1.135 0.427,0.25 0.563,0.677 0.719,0.677 0.719,0.677 1.01,0.958 true 0.104,0.073 0.417,0.229 0.313,0.156 10 false *a 0.281,0.917 0.677,1.125 0.396,0.208 10 false L25 0.313,0.573 0.625,0.729 0.313,0.156 10 false IG+
*a Component with harness connected
(Combination Meter Assembly)


Remove the combination meter assembly with the connector(s) still connected.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
L25-13 (IG+) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPLACE COMBINATION METER ASSEMBLY