Refer to DTC P0136.
Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>P0136
Sensor 2 refers to the sensor mounted behind the Three-Way Catalytic Converter (TWC) and located far from the engine assembly.
When any of these DTCs are stored, the ECM enters fail-safe mode. The ECM turns off the heated oxygen sensor heater in fail-safe mode. Fail-safe mode continues until the ignition switch is turned off.
The ECM provides a pulse width modulated control circuit to adjust the current through the heater. The heated oxygen sensor sensor heater circuit uses a relay on the +B side of the circuit.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0037 | Oxygen Sensor Heater Control Circuit Low (Bank 1 Sensor 2) | The heater current is less than the specified value while the heater is operating. (1 trip detection logic) |
·
Open in heated oxygen sensor heater (bank 1 sensor 2) circuit
·
Heated oxygen sensor heater (bank 1 sensor 2)
·
EFI NO. 2 fuse
·
ECM |
Comes on | DTC stored |
| P0038 | Oxygen Sensor Heater Control Circuit High (Bank 1 Sensor 2) | The heater current is higher than the specified value while the heater is operating. (1 trip detection logic) |
·
Short in heated oxygen sensor heater (bank 1 sensor 2) circuit
·
Heated oxygen sensor heater (bank 1 sensor 2)
·
EFI NO. 2 fuse
·
ECM |
Comes on | DTC stored |
| P0057 | Oxygen Sensor Heater Control Circuit Low (Bank 2 Sensor 2) | The heater current is less than the specified value while the heater is operating. (1 trip detection logic) |
·
Open in heated oxygen sensor heater (bank 2 sensor 2) circuit
·
Heated oxygen sensor heater (bank 2 sensor 2)
·
EFI NO. 2 fuse
·
ECM |
Comes on | DTC stored |
| P0058 | Oxygen Sensor Heater Control Circuit High (Bank 2 Sensor 2) | The heater current is higher than the specified value while the heater is operating. (1 trip detection logic) |
·
Short in heated oxygen sensor heater (bank 2 sensor 2) circuit
·
Heated oxygen sensor heater (bank 2 sensor 2)
·
EFI NO. 2 fuse
·
ECM |
Comes on | DTC stored |
| P102D | O2 Sensor Heater Circuit Performance Bank 1 Sensor 2 Stuck ON | The heater current is higher than the specified value while the heater is not operating. (1 trip detection logic) |
ECM Short in heated oxygen sensor heater (bank 1 sensor 2) circuit |
Comes on | DTC stored |
| P105D | O2 Sensor Heater Circuit Performance Bank 2 Sensor 2 Stuck ON | The heater current is higher than the specified value while the heater is not operating. (1 trip detection logic) |
ECM Short in heated oxygen sensor heater (bank 2 sensor 2) circuit |
Comes on | DTC stored |
The sensing portion of the heated oxygen sensor has a zirconia element which is used to detect the oxygen concentration in the exhaust gas. If the zirconia element is at the appropriate temperature, and the difference between the oxygen concentrations surrounding the inside and outside surfaces of the sensor is large, the zirconia element generates voltage signals. In order to increase the oxygen concentration detecting capacity of the zirconia element, the ECM supplements the heat from the exhaust with heat from a heating element inside the sensor.
The ECM monitors the current applied to the heated oxygen sensor heater to check the heater for malfunctions. If the heater current is outside the normal range, the signal transmitted by the heated oxygen sensor becomes inaccurate. When the current in the heated oxygen sensor heater is outside the normal operating range, the ECM interprets this as a malfunction in the sensor and stores a DTC.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the GTS on [A].
Start the engine and idle it for 5 minutes or more [B].
With the vehicle stationary, depress the accelerator pedal and maintain an engine speed of 3000 rpm for 1 minute [C].
Idle the engine for 5 minutes or more [D].
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [E].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0037, P0038, P0057, P0058, P102D or P105D.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL |
·
DTC judgment completed
·
System normal |
| ABNORMAL |
·
DTC judgment completed
·
System abnormal |
| INCOMPLETE |
·
DTC judgment not completed
·
Perform driving pattern after confirming DTC enabling conditions |
| N/A |
·
Unable to perform DTC judgment
·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [E] again.
Refer to DTC P0136.
Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>P0136
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Bank 1 refers to the bank that includes the No. 1 cylinder*.
*: The No. 1 cylinder is the cylinder which is farthest from the transmission.
Bank 2 refers to the bank that does not include the No. 1 cylinder.
Sensor 1 refers to the sensor closest to the engine assembly.
Sensor 2 refers to the sensor farthest away from the engine assembly.
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Inspect the heated oxygen sensor.
Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>HEATED OXYGEN SENSOR>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *A | Bank 1 |
| *B | Bank 2 |
| *a | Front view of wire harness connector (to Heated Oxygen Sensor) |
Disconnect the heated oxygen sensor connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C18-2 (+B) - Body ground | Ignition switch ON | 11 to 14 V |
| C17-2 (+B) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the heated oxygen sensor (bank 1 sensor 2) connector.
Disconnect the heated oxygen sensor (bank 2 sensor 2) connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C18-1 (HT1B) - C39-48 (HT1B) | Always | Below 1 Ω |
| C17-1 (HT2B) - C39-47 (HT2B) | Always | Below 1 Ω |
| C18-1 (HT1B) or C39-48 (HT1B) - Body ground | Always | 10 kΩ or higher |
| C17-1 (HT2B) or C39-47 (HT2B) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG