Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/ Pre-collision System) › from 2022.09
RM25T0E _57 Power Source / Network _057931 NETWORKING _0556385 CAN COMMUNICATION SYSTEM(w/ Pre-collision System) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/ Pre-collision System)  Steering Angle Sensor Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Steering Angle Sensor Communication Stop Mode Communication stop for "Spiral cable (Steering Angle Sensor)" is indicated on the "Communication Bus Check" screen of the GTS.
(Click here)
·

Power source circuit of spiral with sensor cable sub-assembly (steering angle sensor)

·

Spiral with sensor cable sub-assembly (steering angle sensor) ground circuit

·

Spiral with sensor cable sub-assembly (steering angle sensor) CAN branch wire or connector

·

Spiral with sensor cable sub-assembly (steering angle sensor)



WIRING DIAGRAM

C240994E08
4.646,3.948 5.219,4.271 0.573,0.323 10 false L47 4.615,4.094 7.073,4.448 2.458,0.354 10 false Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor) 5.75,1.094 6.167,1.271 0.417,0.177 10 false CANL 5.75,0.563 6.156,0.75 0.406,0.188 10 false CANH 5.563,0.469 5.677,0.625 0.115,0.156 10 false 4 5.563,0.99 5.719,1.135 0.156,0.146 10 false 3 5.75,3.156 6.177,3.333 0.427,0.177 10 false ESS 5.771,2.635 6.177,2.823 0.406,0.188 10 false IG 5.76,2.125 6.156,2.281 0.396,0.156 10 false BAT 5.563,2.01 5.677,2.167 0.115,0.156 10 false 6 5.552,2.521 5.656,2.677 0.104,0.156 10 false 5 5.552,3.031 5.656,3.188 0.104,0.156 10 false 2 1.604,0.469 1.76,0.635 0.156,0.167 10 false 6 1.573,0.969 1.802,1.115 0.229,0.146 10 false 17 0.5,1.385 0.833,1.531 0.333,0.146 10 false I134 0.51,1.552 3.229,1.854 2.719,0.302 10 false No. 7 Global CAN Junction Connector 1.708,2.052 2.698,2.354 0.99,0.302 10 false from Battery 1.396,2.583 2.771,2.865 1.375,0.281 10 false from IG1 1 Relay 3.823,2.823 4.906,2.99 1.083,0.167 10 false ECU IG 3.823,2.271 4.302,2.448 0.479,0.177 10 false ECU-B

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Pre-collision System)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

When disconnecting and reconnecting the battery.

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Pre-collision System)>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (STEERING ANGLE SENSOR CAN BRANCH WIRE)
a.
C234977C10
0.479,1.052 1.063,1.323 0.583,0.271 1.813,1.302 2.177,1.781 2.177,1.781 2.292,1.781 true 1.635,1.271 1.292,1.74 1.292,1.74 1.188,1.74 true 0.615,1.073 0.99,1.302 0.375,0.229 10 false L47 0.781,1.646 1.208,1.813 0.427,0.167 10 false CANH 2.354,1.677 2.75,1.854 0.396,0.177 10 false CANL 0.188,0.104 0.49,0.271 0.302,0.167 10 false *a
*a Rear view of wire harness connector
(to Spiral with Sensor Cable Sub-assembly [Steering Angle Sensor])


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the spiral with sensor cable sub-assembly (steering angle sensor) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L47-4 (CANH) - L47-3 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY [STEERING ANGLE SENSOR] POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY [STEERING ANGLE SENSOR] CAN BRANCH WIRE OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY [STEERING ANGLE SENSOR] POWER SOURCE CIRCUIT)
a.
C234977C09
2.417,1.031 2.969,1.313 0.552,0.281 1.927,1.323 2.198,1.781 2.198,1.781 2.302,1.781 true 1.406,1.208 1.188,0.938 1.188,0.938 1.042,0.938 true 1.542,1.313 1.208,1.792 1.208,1.792 1.042,1.792 true 2.552,1.073 2.885,1.219 0.333,0.146 10 false L47 0.75,0.833 1.063,0.979 0.313,0.146 10 false BAT 0.833,1.667 1.052,1.833 0.219,0.167 10 false IG 2.354,1.677 2.802,1.938 0.448,0.26 10 false ESS 0.073,0.031 0.375,0.198 0.302,0.167 10 false *a
*a Rear view of wire harness connector
(to Spiral with Sensor Cable Sub-assembly [Steering Angle Sensor])


Connect the cable to the negative (-) battery terminal.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L47-6 (BAT) - Body ground Always 11 to 14 V
L47-5 (IG) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L47-2 (ESS) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY (STEERING ANGLE SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR