Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/ Pre-collision System) › from 2022.09
RM25T0E _57 Power Source / Network _057931 NETWORKING _0556385 CAN COMMUNICATION SYSTEM(w/ Pre-collision System) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/ Pre-collision System)  ECM Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
ECM Communication Stop Mode Communication stop for "ECM (Engine)" is indicated on the "Communication Bus Check" screen of the GTS.
(Click here)
·

Power source circuit of ECM

·

ECM ground circuit

·

ECM CAN main wire or connector

·

ECM



WIRING DIAGRAM

C373834E02
0.292,1.438 2.729,1.74 2.438,0.302 10 false No. 7 Gloabl CAN Junction Connector 5.625,0.396 6.24,0.594 0.615,0.198 10 false CANH 5.615,1.188 6.229,1.385 0.615,0.198 10 false CANL 5.604,1.948 6.219,2.146 0.615,0.198 10 false BATT 5.594,2.49 6.208,2.688 0.615,0.198 10 false +B 5.604,3.479 6.219,3.677 0.615,0.198 10 false MREL 5.594,4.01 6.208,4.208 0.615,0.198 10 false IGSW 5.604,4.521 6.219,4.719 0.615,0.198 10 false E01 5.604,5.01 6.219,5.208 0.615,0.198 10 false E05 5.594,5.49 6.208,5.688 0.615,0.198 10 false E1 5.604,5.958 6.219,6.156 0.615,0.198 10 false EC 3.802,2.094 4.563,2.323 0.76,0.229 10 false EFI MAIN 4.042,4.146 4.656,4.344 0.615,0.198 10 false IGN 5.229,0.542 5.844,0.74 0.615,0.198 10 false A29 5.24,1.063 5.854,1.26 0.615,0.198 10 false A29 5.229,1.948 5.844,2.146 0.615,0.198 10 false A29 5.24,2.49 5.854,2.688 0.615,0.198 10 false A29 5.24,3.469 5.854,3.667 0.615,0.198 10 false A29 5.24,4 5.854,4.198 0.615,0.198 10 false A29 5.25,5.958 5.865,6.156 0.615,0.198 10 false A29 5.24,4.51 5.854,4.708 0.615,0.198 10 false C39 5.24,4.99 5.854,5.188 0.615,0.198 10 false C39 5.229,5.469 5.844,5.667 0.615,0.198 10 false C39 5.26,0.333 5.875,0.531 0.615,0.198 10 false 41 5.26,0.865 5.875,1.063 0.615,0.198 10 false 49 5.26,1.75 5.875,1.948 0.615,0.198 10 false 20 5.292,2.271 5.906,2.469 0.615,0.198 10 false 2 5.271,3.26 5.885,3.458 0.615,0.198 10 false 44 5.271,3.802 5.885,4 0.615,0.198 10 false 28 5.292,4.323 5.906,4.521 0.615,0.198 10 false 22 5.281,4.792 5.896,4.99 0.615,0.198 10 false 23 5.281,5.281 5.896,5.479 0.615,0.198 10 false 81 5.292,5.76 5.906,5.958 0.615,0.198 10 false 32 0.24,1.26 0.854,1.458 0.615,0.198 10 false I134 1.729,1.927 3.708,2.198 1.979,0.271 10 false from Battery 1.458,2.448 3.438,2.719 1.979,0.271 10 false from MAIN Relay 1.552,3.438 3.531,3.708 1.979,0.271 10 false to MAIN Relay 1.313,4 3.292,4.271 1.979,0.271 10 false from Ignition Switch 5.823,6.417 6.438,6.615 0.615,0.198 10 false ECM 1.542,0.969 2.156,1.167 0.615,0.198 10 false 12 1.552,0.458 2.167,0.656 0.615,0.198 10 false 1

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Pre-collision System)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

When disconnecting and reconnecting the battery.

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Pre-collision System)>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (ECM CAN MAIN WIRE)
a.
C363469C05
1.573,0.292 2.031,0.521 0.458,0.229 2.427,1.354 2.656,1.167 2.656,1.167 2.823,1.167 true 2.427,1.458 2.625,1.938 2.625,1.938 2.792,1.938 true 0.135,0.094 0.448,0.25 0.313,0.156 10 false *a 2.875,1.042 3.385,1.292 0.51,0.25 10 false CANH 2.833,1.823 3.344,2.073 0.51,0.25 10 false CANL 1.677,0.333 2.188,0.583 0.51,0.25 10 false A29
*a Front view of wire harness connector
(to ECM)


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A29-41 (CANH) - A29-49 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (ECM POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE ECM CAN MAIN WIRE OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (ECM POWER SOURCE CIRCUIT)
a.

Connect the cable to the negative (-) battery terminal.


b.

Disconnect the ECM connector.

C234869C22
1.99,0.49 2.458,0.76 0.469,0.271 4.594,0.5 5.063,0.771 0.469,0.271 1.542,0.708 1.76,0.708 1.76,0.708 1.958,1.219 true 5.719,1.188 5.958,0.792 5.958,0.792 6.177,0.792 true 5.813,2.313 5.51,2.313 5.51,2.313 5.208,1.646 true 1.115,1.01 1.333,1.01 1.333,1.01 1.865,1.385 true 1.896,2.5 2.115,2.5 2.115,2.5 2.344,1.719 true 1.229,2.198 1.448,2.198 1.448,2.198 1.938,1.677 true 5.583,1.208 5.854,0.604 5.854,0.604 6.073,0.604 true 3,0.667 2.75,0.667 2.75,0.667 2.604,1.375 true 0.125,0.073 0.417,0.25 0.292,0.177 10 false *a 6.135,0.5 6.677,0.802 0.542,0.302 10 false E01 5.875,2.198 6.74,2.365 0.865,0.167 10 false E1 4.698,0.521 5.031,0.698 0.333,0.177 10 false C39 0.76,0.917 1.188,1.083 0.427,0.167 10 false BATT 1.281,0.604 1.708,0.771 0.427,0.167 10 false +B 1.469,2.396 1.896,2.563 0.427,0.167 10 false MREL 0.958,2.094 1.385,2.26 0.427,0.167 10 false EC 6.229,0.729 6.771,1.031 0.542,0.302 10 false E05 2.104,0.531 2.438,0.708 0.333,0.177 10 false A29 3.073,0.583 3.5,0.75 0.427,0.167 10 false IGSW
*a Front view of wire harness connector
(to ECM)
- -



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A29-20 (BATT) - Body ground Always 11 to 14 V
A29-2 (+B) - Body ground Battery positive (+) voltage applied to terminal A29-44 (MREL) 11 to 14 V
A29-28 (IGSW) - Body ground Ignition switch ON 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A29-32 (EC) - Body ground Always Below 1 Ω
C39-22 (E01) - Body ground Always Below 1 Ω
C39-23 (E05) - Body ground Always Below 1 Ω
C39-81 (E1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR