Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/ Pre-collision System) › from 2022.09
RM25T0E _57 Power Source / Network _057931 NETWORKING _0556385 CAN COMMUNICATION SYSTEM(w/ Pre-collision System) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/ Pre-collision System)  Center Airbag Sensor Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Center Airbag Sensor Communication Stop Mode Communication stop for "Airbag" is indicated on the "Communication Bus Check" screen of the GTS.
(Click here)
·

Power source circuit of airbag sensor assembly

·

Airbag sensor assembly ground circuit

·

Airbag sensor assembly CAN branch wire or connector

·

Airbag sensor assembly



WIRING DIAGRAM

C494970E01
5.417,3.938 6.781,4.313 1.365,0.375 10 false I51 5.417,4.104 7.031,4.49 1.615,0.385 10 false Airbag Sensor Assembly 5.583,3.313 6.948,3.688 1.365,0.375 10 false E2 5.583,2.708 6.948,3.083 1.365,0.375 10 false E1 5.583,2.125 6.948,2.5 1.365,0.375 10 false IG2 5.583,0.677 6.948,1.052 1.365,0.375 10 false CANH 5.583,1.271 6.948,1.646 1.365,0.375 10 false CANL 5.313,2 6.677,2.375 1.365,0.375 10 false 21 5.302,2.625 6.667,3 1.365,0.375 10 false 25 5.302,3.208 6.667,3.583 1.365,0.375 10 false 26 5.333,1.146 6.698,1.521 1.365,0.375 10 false 22 5.333,0.583 6.698,0.958 1.365,0.375 10 false 13 1.677,0.583 3.042,0.958 1.365,0.375 10 false 3 1.656,1.115 3.021,1.49 1.365,0.375 10 false 14 0.417,1.625 1.781,2 1.365,0.375 10 false I134 0.417,1.792 3.01,2.031 2.594,0.24 10 false No. 7 Global CAN Junction Connector 2.125,2.094 4.813,2.385 2.688,0.292 10 false from Ignition Switch 4.354,2.302 5.354,2.594 1,0.292 10 false IGN

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Pre-collision System)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

When disconnecting and reconnecting the battery.

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Pre-collision System)>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (AIRBAG SENSOR ASSEMBLY CAN BRANCH WIRE)
a.
C210016C23
0.302,1 0.75,1.302 0.448,0.302 1.99,1.083 2.438,0.667 2.438,0.667 2.573,0.667 true 2.094,1.302 2.396,1.635 2.396,1.635 2.542,1.635 true 0.052,0.063 0.24,0.24 0.188,0.177 10 false *a 2.625,0.552 3.063,0.729 0.438,0.177 10 false CANH 0.417,1.052 0.885,1.344 0.469,0.292 10 false I51 2.604,1.521 3.042,1.698 0.438,0.177 10 false CANL
*a Rear view of wire harness connector
(to Airbag Sensor Assembly)


Disconnect the cable from the negative (-) battery terminal and wait at least 90 seconds.


b.

Disconnect the airbag sensor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I51-13 (CANH) - I51-22 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (AIRBAG SENSOR ASSEMBLY POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE AIRBAG SENSOR ASSEMBLY CAN BRANCH WIRE OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (AIRBAG SENSOR ASSEMBLY POWER SOURCE CIRCUIT)
a.
C210016C24
0.323,1.021 0.792,1.323 0.469,0.302 2.188,1.271 2.49,1.104 2.49,1.104 2.625,1.104 true 1.771,1.292 2.083,1.844 2.083,1.844 2.229,1.844 true 1.646,1.313 1.302,1.719 1.302,1.719 1.125,1.719 true 0.052,0.052 0.24,0.229 0.188,0.177 10 false *a 2.677,0.99 3.115,1.167 0.438,0.177 10 false IG2 0.427,1.052 0.927,1.5 0.5,0.448 10 false I51 2.292,1.729 2.729,1.906 0.438,0.177 10 false E1 0.927,1.594 1.365,1.771 0.438,0.177 10 false E2
*a Rear view of wire harness connector
(to Airbag Sensor Assembly)


Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
I51-21 (IG2) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I51-25 (E1) - Body ground Always Below 1 Ω
I51-26 (E2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPLACE HARNESS AND CONNECTOR