Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/ Pre-collision System) › from 2022.09
RM25T0E _57 Power Source / Network _057931 NETWORKING _0556385 CAN COMMUNICATION SYSTEM(w/ Pre-collision System) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/ Pre-collision System)  Brake Actuator (Skid Control ECU) Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Skid Control ECU Communication Stop Mode Communication stop for "Skid Control (ABS/VSC/TRAC)" is indicated on the "Communication Bus Check" screen of the GTS.
(Click here)
·

Power source circuit of brake actuator assembly (skid control ECU)

·

Brake actuator assembly (skid control ECU) ground circuit

·

Brake actuator assembly (skid control ECU) CAN branch wire or connector

·

Brake actuator assembly (skid control ECU)



WIRING DIAGRAM

C494973E01
0.094,1.385 2.719,1.667 2.625,0.281 10 false No. 7 Global CAN Junction Connector 0.083,1.229 2.125,1.479 2.042,0.25 10 false I134 1.604,0.417 2.135,0.719 0.531,0.302 10 false 5 1.552,0.833 2.083,1.135 0.531,0.302 10 false 16 5.615,0.563 6.167,0.802 0.552,0.24 10 false CANH 5.615,0.979 6.167,1.219 0.552,0.24 10 false CANL 5.604,1.771 6.156,2.01 0.552,0.24 10 false +BS 5.646,2.344 6.198,2.583 0.552,0.24 10 false BM 5.625,2.927 6.177,3.167 0.552,0.24 10 false IG1 5.635,4.01 6.188,4.25 0.552,0.24 10 false GND1 5.625,4.5 6.177,4.74 0.552,0.24 10 false GND2 5.177,5.042 6.781,5.552 1.604,0.51 10 false Brake Actuator Assembly (Skid Control ECU) 5.281,0.417 5.813,0.719 0.531,0.302 10 false 27 5.281,0.833 5.813,1.135 0.531,0.302 10 false 43 5.26,1.677 5.792,1.979 0.531,0.302 10 false 14 5.271,2.24 5.802,2.542 0.531,0.302 10 false 46 5.271,2.813 5.802,3.115 0.531,0.302 10 false 45 5.292,3.854 5.823,4.156 0.531,0.302 10 false 1 5.271,4.344 5.802,4.646 0.531,0.302 10 false 30 3.99,1.583 5.219,1.781 1.229,0.198 10 false ABS SOL 3.938,2.188 5.167,2.385 1.229,0.198 10 false ABS MTR 4.01,2.771 5.24,2.969 1.229,0.198 10 false ECU IG 2.031,1.74 3.26,1.938 1.229,0.198 10 false from Battery 2.042,2.333 3.271,2.531 1.229,0.198 10 false from Battery 1.792,2.938 4.615,3.208 2.823,0.271 10 false from IG1 1 Relay 5.177,4.865 6.771,5.083 1.594,0.219 10 false A45

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Pre-collision System)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

When disconnecting and reconnecting the battery.

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Pre-collision System)>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (SKID CONTROL ECU CAN BRANCH WIRE)
a.
C494974C02
1.375,0.188 1.865,0.406 0.49,0.219 2.052,1.156 2.135,0.281 2.135,0.281 2.344,0.281 true 2.073,1.292 2.177,1.906 2.177,1.906 2.344,1.906 true 0.125,0.094 0.438,0.25 0.313,0.156 10 false *a 1.5,0.208 1.813,0.365 0.313,0.156 10 false A45 2.385,0.188 2.885,0.427 0.5,0.24 10 false CANL 2.396,1.813 2.896,2.052 0.5,0.24 10 false CANH
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the brake actuator assembly (skid control ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A45-27 (CANH) - A45-43 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY [SKID CONTROL ECU] POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE BRAKE ACTUATOR ASSEMBLY [SKID CONTROL ECU] CAN BRANCH WIRE OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY [SKID CONTROL ECU] POWER SOURCE CIRCUIT)
a.
C494974C03
1.438,0.208 1.927,0.427 0.49,0.219 2.406,0.948 2.688,0.302 2.688,0.302 2.865,0.302 true 0.406,0.698 0.573,0.698 0.573,0.698 0.885,0.958 true 2.24,1.302 2.469,1.917 2.469,1.917 2.656,1.917 true 2.458,1.24 2.823,1.74 2.823,1.74 3.01,1.74 true 0.469,1.719 0.615,1.719 0.615,1.719 0.927,1.25 true 0.125,0.094 0.438,0.25 0.313,0.156 10 false *a 1.552,0.229 1.865,0.385 0.313,0.156 10 false A45 2.708,1.833 3.208,2.073 0.5,0.24 10 false IG1 2.896,0.24 3.292,0.5 0.396,0.26 10 false +BS 0.031,0.625 0.427,0.885 0.396,0.26 10 false GND1 3.063,1.646 3.375,1.927 0.313,0.281 10 false BM 0.063,1.646 0.458,1.906 0.396,0.26 10 false GND2
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])


Connect the cable to the negative (-) battery terminal.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A45-14 (+BS) - Body ground Always 11 to 14 V
A45-46 (BM) - Body ground Always 11 to 14 V
A45-45 (IG1) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A45-1 (GND1) - Body ground Always Below 1 Ω
A45-30 (GND2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR