Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM (w/ Pre-collision System) › from 2022.09
RM25T0E _54 Brake _029873 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0548732 VEHICLE STABILITY CONTROL SYSTEM(w/ Pre-collision System) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(w/ Pre-collision System)  P057113  Brake Switch "A" Circuit Open  


DESCRIPTION

The skid control ECU (brake actuator assembly) detects the brake operating conditions through a signal transmitted by the stop light switch.

The skid control ECU incorporates a circuit to detect an open circuit. This DTC is output when an open circuit is detected in the stop light signal input line.

DTC No. Detection Item DTC Detection Condition Trouble Area
P057113 Brake Switch "A" Circuit Open When the +BS terminal voltage is 9.5 V or higher, the stop light drive output (STPO) is OFF continuously for 0.1 seconds or more and there is an open circuit between A and B in the STP terminal circuit continuously for 0.3 seconds or more.
·

Wire harness or connector

·

Skid control ECU (Brake actuator assembly)



WIRING DIAGRAM

C494254E01
0.792,1.01 2.792,1.333 2,0.323 10 false Stop Light Switch Assembly 1.74,3.052 4.021,3.313 2.281,0.26 10 false Stop Light Control Relay (STP LP) 3.552,4.25 4.958,4.667 1.406,0.417 10 false to Stop Light Circuit 2.271,3.833 3.333,4.052 1.063,0.219 10 false from IG Circuit 5.385,4.656 6.948,5.083 1.563,0.427 10 false Skid Control ECU (Brake Actuator Assembly) 5.073,4.656 5.385,4.896 0.313,0.24 10 false A45 1.146,4.042 1.958,4.24 0.813,0.198 10 false ECU IG 0.625,5.073 1.281,5.313 0.656,0.24 10 false STOP 1.51,4.875 2.396,5.073 0.885,0.198 10 false from Battery 0.49,1.021 0.802,1.26 0.313,0.24 10 false I19 5.406,0.448 5.844,0.656 0.438,0.208 10 false STP2 5.406,1.813 5.896,2.104 0.49,0.292 10 false STP 5.417,2.479 5.906,2.771 0.49,0.292 10 false STPO 0.771,0.438 0.906,0.635 0.135,0.198 10 false 2 5.104,1.792 5.344,1.99 0.24,0.198 10 false 11 5.104,2.49 5.344,2.688 0.24,0.198 10 false 32 2.135,2.427 2.271,2.625 0.135,0.198 10 false 2 3.375,2.438 3.51,2.635 0.135,0.198 10 false 1 3.385,1.813 3.521,2.01 0.135,0.198 10 false 3 2.146,1.823 2.281,2.021 0.135,0.198 10 false 5 2.625,1.385 2.76,1.583 0.135,0.198 10 false 4 2.135,0.438 2.271,0.635 0.135,0.198 10 false 1 4.615,2.073 4.854,2.271 0.24,0.198 10 false A 5.156,2.063 5.396,2.26 0.24,0.198 10 false B 5.094,0.448 5.333,0.646 0.24,0.198 10 false 37 3.75,0.802 4.635,1.073 0.885,0.271 10 false STP NO. 2 3.875,2.135 4.49,2.333 0.615,0.198 10 false STOP 3.927,2.302 4.698,2.5 0.771,0.198 10 false (15A) 0.656,5.24 1.427,5.438 0.771,0.198 10 false (30A)

CAUTION / NOTICE / HINT

NOTICE:

After replacing the skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/ Pre-collision System)>CALIBRATION


PROCEDURE

1.READ VALUE USING GTS (STOP LIGHT RELAY)
a.

Check that the stop light switch display observed on the GTS changes according to brake pedal operation.

Chassis > Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light Relay Stop light control relay (STP LP relay) OFF / ON OFF: Stop light control relay (STP LP relay) OFF
ON: Stop light control relay (STP LP relay) ON
HINT:

The stop light state is determined using the voltage at terminal STP


Chassis > Brake > Data List
Tester Display
Stop Light Relay
50003 435 67
OK:

The GTS displays OFF / ON according to brake pedal operation.



Result:
Proceed to
OK
NG



OK

2.RECONFIRM DTC

NG

3.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
2.RECONFIRM DTC
a.

Clear the DTCs.

Chassis > Brake > Clear DTCs
50002 435

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Depress the brake pedal several times to test the stop light circuit.


e.

Check if the same DTC is output.

Chassis > Brake > Trouble Codes
50001 435
Result:
Result Proceed to
DTC P057113 is not output. A
DTC P057113 is output. B




A

B

3.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
a.
C494113C10
1.542,0.094 2,0.333 0.458,0.24 2.125,0.938 2.135,1.771 true 2.021,1.833 2.479,2.063 0.458,0.229 10 false STP 1.635,0.135 1.938,0.344 0.302,0.208 10 false A45 0.073,0.063 0.385,0.26 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.

Disconnect the A45 skid control ECU (brake actuator assembly) connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A45-11 (STP) - Body ground Stop light switch assembly on (Brake pedal depressed) 8 to 14 V
Stop light switch assembly off (Brake pedal released) Below 1.5 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BRAKE ACTUATOR ASSEMBLY - STOP LIGHT CIRCUIT)